• 한국분말재료학회지
• /
• 제11권2호
• /
• pp.137-142
• /
• 2004

In this study, chemical solution mixing and hydrogen reduction method was used to fabricate nanostructured $Fe_xCo_{1-x}$ alloy powders. Fe-Co chloride mixture, FeCl$_2$ and COCI$_2$ with 99.9％ purity, were reduced in hydrogen atmosphere. Nanostructured Fe-Co alloy powders with a grain size of 50 nm were successfully fabricated. Magnetic properties of fabricated $Fe_xCo_{1-x}$(x=0, 10, 30, 50, 70, 100) alloy powders with the same grain size were measured because size factor can affect magnetic properties. Coercivity of Fe-Co alloy powders were increased with increasing Co contents. Maximum value of coercivity in various Co contented Fe-Co alloy powders with similar grain size was 125 Oe at Fe$_{100}$. Saturation magnetization value at Fe$_{70}$Co$_{30}$ composition showed maximum value of 219 emu/g and saturation magnetization value decreased with increasing Co contents and minimum value of 155 emu/g was observed at Co$_{100}$.

• 한국분말재료학회지
• /
• 제10권5호
• /
• pp.333-336
• /
• 2003

The purpose of this study is the fabrication of nano-sized Fe-Co alloy powders with soft magnetic properties by the slurry mixing and hydrogen reduction (SMHR) process. $FeCl_2$0 and $CoCl_2$ powders with 99.9% purities were used for synthesizing nanostructured Fe-Co alloy powder. Nano-sized Fe-Co alloy powders were successfully fabricated using SMHR, which was performed at 50$0^{\circ}C$ for 1 h in H$_2$ atmosphere. The fabricated Fe-Co alloy powders showed $\alpha$' phase (ordered body centered cubic) with the average particle size of 45 nm. The SMHR powder exhibited low coercivity force of 32.5 Oe and saturation magnetization of 214 emu/g.

• Applied Microscopy
• /
• 제45권1호
• /
• pp.32-36
• /
• 2015

The microstructural features of FeCoCrNi, FeCoCrNiAl and FeCoCrNiSix (x=0, 5, 10, 15, 20) alloys have been investigated in the present study. The microstructure of FeCoCrNi alloy changes dramatically with equiatomic addition of Al. The fcc irregular shaped grain structure in the as-cast FeCoCrNi alloy changes into the bcc interconnected structure with phase separation of Al-Ni rich and Cr-Fe rich phases in the as-cast FeCoCrNiAl alloy. The microstructure of FeCoCrNi alloy changes with the addition of Si. With increasing the amount of Si, the fcc structure of the grains is maintained, but new phase containing higher amount of Si forms at the grain boundary. As the amount of Si increases, the fraction the Si-rich grain boundary phase increases.

• 한국자기학회지
• /
• 제18권6호
• /
• pp.227-231
• /
• 2008

Zr 함량에 따르는 CoFeZr의 합금박막의 구조 및 자기적 특성, 그리고 비정질 CoFeZr을 사용한 스핀밸브의 자기저항 및 열적 안정성에 관하여 연구하였다. Zr 조성이 증가함에 따라 CoFeZr 합금 박막의 포화자기장 및 보자력은 감소하며 완전히 비정질이 형성되었을때 보자력은 최소 값을 보였다. Zr의 함량이 약 18 at% 이상일 때 완전한 비정질이 형성되었다. 비정질 CoFeZr을 스핀밸브에 적용하였을 때 기존의 CoFe을 사용한 스핀밸브보다 자기저항비와 교환결합력은 약간 감소하는 경향을 확인 하였다. 이는 비정질 자성체의 상대적으로 높은 저항값에 기인하였다. 그러나 ${\Delta}{\rho}$, 즉 스핀의존산란은 향상되었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.950-952
• /
• 2000

Considering the effective distribution coefficient of Ni in Fe-Ni-Co invar alloy containing a little amount of carbon, we investigated on the thermal expansion coefficient(${\alpha}$). Fe-Ni-Co invar alloy had a large thermal expansion coefficient in as-casted compared with solution treated. The thermal expansion coefficient of Fe-Ni-Co alloy increased with the carbon content in both state of as-casted and solution treated. The effective distribution coefficient(Ke$\^$Ni/) of Ni was smaller than unity in alloy of not containing carbon, but is way larger than unity in alloy of containing carbon. It was considered that the homogeneity of Ni in primary austenite affected thermal expansion coefficient.

• 한국표면공학회지
• /
• 제29권3호
• /
• pp.195-202
• /
• 1996

The composition, the microstructure and the magnetic properties(HC and Hk) of Fe-Co-Ni alloy electrodeposits were investigated according to the electrolysis conditions using sulfate bath paddle agitated. The current efficiency of the alloys electrodeposition was considerably low in the range of 16∼50%. The Fe content(wt.%) of the alloy increased from 20% to 57% with current density, while Ni content of them decreased in the range of 70∼24% respectively, and Co content was nearly constant. As a result, Fe/Ni ratio of the alloy increased from 0.3 to 2.0 showing the anomalous codeposition. The structure of the alloy changed from fcc to the mixed one of fcc+bcc with the increase of Fe/Ni ratio. The preferred orientation of the alloy with fcc and bcc structure were (220) and (110) respectively. The alloy with Fe/Ni ratio(0.3∼l.2) had the lowest coercivity of 0.4∼0.8 Oe.

• 한국자기학회지
• /
• 제27권4호
• /
• pp.129-134
• /
• 2017

합금 제조에 흔히 이용되는 기존의 용해, 응고, 열처리 등의 가공 공정으로 덩치 형태의 체심정방정 구조의 Fe-Co계 합금상을 합성하고, 그 결정학적, 자기적 특성을 조사하였다. $(Fe_{100-x}Co_x)_{1-y}C_y$ 합금에서 체심정방정 구조의 단일상(martensite)이 얻어지는 Co 및 C의 함량은 크게 제한되어, Co의 함량 x = 2.5, C의 함량 y = 0.062로 제한된 조성에서 체심정방정 구조의 단일상 합금이 얻어졌다. 합성된 조성 $(Fe_{97.5}Co_{2.5})_{0.938}C_{0.062}$인 체심정방정 구조의 단일상 합금의 정방성(tetragonality, c/a)은 1.05였으며, 이 합금의 결정자기 이방성 상수, $K_1$ 값은 순수 철(${\alpha}-Fe$)의 $K_1$ 값에 비하면 3.1배 정도 높은 $1.5{\times}10^5J/m^3$였다.

• 한국분말재료학회지
• /
• 제26권2호
• /
• pp.112-118
• /
• 2019

Infiltration is a popular technique used to produce valve seat rings and guides to create dense parts. In order to develop valve seat material with a good thermal conductivity and thermal expansion coefficient, Cu-infiltrated properties of sintered Fe-Co-M(M=Mo,Cr) alloy systems are studied. It is shown that the copper network that forms inside the steel alloy skeleton during infiltration enhances the thermal conductivity and thermal expansion coefficient of the steel alloy composite. The hard phase of the CoMoCr and the network precipitated FeCrC phase are distributed homogeneously as the infiltrated Cu phase increases. The increase in hardness of the alloy composite due to the increase of the Co, Ni, Cr, and Cu contents in Fe matrix by the infiltrated Cu amount increases. Using infiltration, the thermal conductivity and thermal expansion coefficient were increased to 29.5 W/mK and $15.9um/m^{\circ}C$, respectively, for tempered alloy composite.

• 한국자기학회지
• /
• 제7권6호
• /
• pp.308-313
• /
• 1997

조성과 강자성 상하지층이 CoFe-Ag 나노입상 합금박막의 거대자기저항과 포화자기장에 미치는 효과에 대하여 연구하였다. 3000 .angs. 두께의 ( $Co_{92}$Fe$_{8}$)$_{31}$Ag$_{69}$ 합금박막에서 최대 자기저항 25.7%를 얻었고, 그 때 포화자장은 2.1 kOe 이었다. 100 .angs. 두께의 박막은 자기저항비가 1.2%이고 포화자장은 5.2 kOe 이었다. 200 .angs. 두께의 합금 박막에 100 .angs. Fe를 상하지층으로 증착하였을 때 자기저항은 9.5 %dptj 11 %로 증가하였고 포화자기장은 2.8 kOe에서 1.8 kOe로 개선되었다. 300 .angs. 이하의 합금박막에 강자성 상하지층의 피복은 교환결합에 의하여 합금박막의 포화자기장을 감소시키는 효과가 있었다. 강자성 상하지층에 의한 자기저항의 증가는 표면에서의 전도전자의 스핀 전도산란의 감소와 계면저항에 의한 전류새흐름의 감소로 기인되는 것으로 보인다. 자기저항의 증가 효과는 합금박막의 두께가 약 300 .angs. 이하에서 나타났다. 교환결합 강자성체인 NiFe 그리고 Fe 중에서 Fe가 교환결합에 의한 포화자기장 감소에 좀더 효과적이었다.

• 한국표면공학회지
• /
• 제28권6호
• /
• pp.352-360
• /
• 1995

The effect of electrolysis conditions on the composition, the magnetic properties and the preferred orientation of Ni-Fe-Co alloy deposits was investigated using the sulfate-chloride bath paddle agitated. Cathode current efficiency increases with the current density, showing the different tendency of the variation from that of the Ni-Fe electrodeposits. The Co content of the deposits decreases with increasing current density, while the content of Ni and Fe is shown to be minimum or maximum at 3A/$dm^2$ respectively. The Ni/Fe ratio of the alloy deposits is lower than that of Ni-Fe deposits. The coercive force($H_c$) of the deposits increases with the Co content in deposit, showing the relatively low value in the range of 1.8~5.0Wt.% Co. The anisotropy field ($H_k$) of the deposits is higher than that of Ni-Fe alloy deposits, The preferred orientation of the deposits is generally (200), but the orientation factor(R) changes with both the increase of current density and the magnetic field applied during deposition.