• 한국정밀공학회지
• /
• 제27권8호
• /
• pp.42-47
• /
• 2010

In this paper, the characteristics of contact surface damage due to fretting in a press-fitted shaft below the fretting fatigue limit are proposed by experimental methods. A series of fatigue tests and interrupted fatigue tests of small scale press-fitted specimen were carried out by using rotating bending fatigue test machine. Macroscopic and microscopic characteristics were examined using scanning electron microscope (SEM), optical microscope or profilometer. It is found that fretting fatigue cracks were initiated even under the fretting fatigue limit on the press-fitted shafts by fretting damage. The fatigue cracks of press-fitted shafts were initiated from the edge of contact surface and propagated inward in a semi-elliptical shape. Furthermore, the fretting wear rates at the contact edge are increased rapidly at the initial stage of total fatigue life. After steep increasing, the increase of wear rate is nearly constant under the load condition below the fretting fatigue limit. It is thus suggested that the fretting wear must be considered on the fatigue life evaluation because the fatigue crack nucleation and propagation process is strongly related to the evolution of surface profile by fretting wear in the press-fitted structures.

• 한국철도학회논문집
• /
• 제10권5호
• /
• pp.546-553
• /
• 2007

본 연구는 압입축에 프레팅이 발생할 경우 프레팅 마모에 의한 접촉형상의 변화가 접촉응력의 분포, 균열발생 위치에 미치는 영향을 분석하고자 하였다. 압입축의 프레팅 피로실험시 측정한 접촉면의 프로파일을 이용하여 유한요소 해석을 수행하고 피로 사이클별 마모형상 변화에 따른 접촉면의 응력 변화를 분석하였다. 접촉면의 응력 해석결과를 이용하여 프레팅 피로손상 파라미터와 다축 피로이론를 적용하여 마모에 따른 균열발생위치의 변화를 해석하고 실험과 비교, 분석하였다. 프레팅 마모에 의해 접촉 끝단의 응력집중은 초기에 급격하게 감소하며, 마모가 진행될수록 응력집중의 위치는 접촉끝단에서 안쪽으로 이동한다. 따라서 프레팅 마모에 의한 접촉응력의 변화가 균열발생 위치의 변차와 다중균열발생의 주요원인임을 명확히 하였다.

• Tribology and Lubricants
• /
• 제10권2호
• /
• pp.51-55
• /
• 1994

Rolling friction test was carried out to investigate the effect of the wear amount on rolling contact fatigue process in lubrication oil. The methods of this process were conducted at two Hertzian contact pressure and three slide ratio in each case by employing normalized and annealed carbon steel. During process of the rolling contact fatigue, the number of rotation until surface damage was occurred, the wear amount of rolling contact surface, and residual stress and half-value breadth using X-ray reflection on rolling contact surface were investigated. The result of this study shows that rolling contact fatigue process was directly influenced by wear trend and was confirmed by change of residual stress and half-value breadth on rolling contact surface.

• Tribology and Lubricants
• /
• 제16권6호
• /
• pp.477-483
• /
• 2000

Rolling contact fatigue (RCF) tests were performed for two kinds of commercial silicon nitride balls using 4-Ball rolling contact fatigue life tester under EHL condition (Λ=8.9) and boundary lubrication condition (Λ=0.2). All the test balls were finished up to the dimensional accuracy of Grade 5 defined in KS B 2001 (Steel Balls for Ball Bearings) with a size of 8.731 mm. RCF tests were then conducted under the initial theoretical maximum contact stress 6.63 GPa and the spindle speed 10,000 rpm. All the test balls were not failed until 3.75 $\times$ 107 contact cycles and wear tracks of test balls were not conspicuous under EHL condition (Λ= 8.9). In the operations of low lambda regime (Λ= 0.2), all the test balls were surface damaged and high rolling wear resistance was achievable in fully densified using MgO 1 wt% and HIPed balls. Rolling wear of silicon nitride balls under boundary lubrication condition depend mainly on grain size and intergranular phase content of silicon nitride balls.

• Tribology and Lubricants
• /
• 제10권3호
• /
• pp.71-77
• /
• 1994

Rolling friction test was carried out to investigate the effect of the wear amount on rolling contact fatigue process in lubrication oil. The methods of this process were conducted at two Hertzian contact pressure and three slide ratio in each case by employing normalized and annealed carbon steel. During process of the rolling contact fatigue, the number of rotation until surface damage was occurred, the wear amount of rolling contact surface, and residual stress and half-value breadth using X-ray reflection on rolling contact surface were investigated. The result of this study shows that rolling contact fatigue process was directly influenced by wear trend and was confirmed by change of residual stress and half-value breadth on rolling contact surface.

• Journal of Ceramic Processing Research
• /
• 제20권5호
• /
• pp.499-504
• /
• 2019

The effect of coating thickness on the contact fatigue and wear of thermal barrier coatings (TBCs) are investigated in this study. The same bondcoat material thickness (250 ㎛) are used for each sample, which allows the effect of the coating thickness of the topcoat to be investigated. TBCs with different coating thicknesses (200, 400, and 600 ㎛) are prepared by changing processing parameters such as the feeding rate of the feedstock, spraying speed, and spraying distance during APS(air plasma spray) coating. The damage size on the surface are strongly affected by the coating thickness effect. Although the damage size from contact fatigue using a spherical indenter diminish at a TBC of 200 ㎛, a high wear resistance such as a low friction coefficient and little mass change are found at a TBC of 600 ㎛. These results indicate that the coating thickness strongly affects the mechanical behavior in TBCs during gas turbine operation.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2002년도 춘계학술발표회 초록집
• /
• pp.38-38
• /
• 2002

Kinetic indentation technique was studied and a method to evaluate wear and fatigue behaviors of irradiated small specimen was suggested. The method is based on both the proportion of elastic and plastic deformation and values obtained by micro-hardness test. The parameters obtained from the diagram of load-indentation depth-time are required to evaluates wear and fatigue properties. Considering the irradiated test specimen, it is one of possible and useful methods to estimate the irradiated wear and fatigue behaviors of the small size specimen. This article briefly describes the status of irradiated material study in domestic research reactor.

• 한국소음진동공학회논문집
• /
• 제24권8호
• /
• pp.643-650
• /
• 2014

Gear transmission system is widely applied in engineering. As the problem of contact fatigue, wear, lubrication failure etc, the condition of gear teeth contacts will be worse. The vibration and sound signals in the gear system will be affected by the some failures like scuffing, abrasive wear and spalling due to the deterioration of gear teeth surface. By studying the estimation of specific film thickness, measurement of reduction in tooth thickness, visual examination of wear mechanisms on the gear teeth and their effects on the statistical parameters of vibration and sound signals, the research obtained the satisfactory results on accessing the surface fatigue wear in a spur gear system. The paper utilizes the relationship between statistical parameters obtained from sound signals and Stribeck curve to confirm the hypothesis of dependency of surface fatigue wear, specific film thickness.

• Tribology and Lubricants
• /
• 제25권4호
• /
• pp.256-260
• /
• 2009

Fretting is a kind of wear which effects on reliability and durability. When machine parts are joined joint in parts such as a bolt or a rivet or a pin, fretting phenomenon is occurred by micro relative movement. When fretting occurs in joint parts, there is wear which is the cause of fatigue crack. Recently, although the ways of assessment of fatigue and damage tolerance are established, there is no way to evaluate fatigue crack initiation life by fretting phenomenon. Consequently, the prediction of life and prevention plan caused by fretting are needed to improve reliability. The objective of this paper is to predict fretting wear by using a experimental method and contact analysis considering wear process. For prediction of fretting wear volume, systematic and controlled experiments with a disc-plate contact under gross slip fretting conditions were carried out. A modified Archard equation is used to calculate wear depths from the contact pressure and stroke using wear coefficients obtained from the disc-plate fretting tests.

• 대한치과보철학회지
• /
• 제37권3호
• /
• pp.313-327
• /
• 1999

The aim of this study was to compare wear resistance of resin denture teeth opposing various restorative materials. The wear resistance of conventional acrylic resin teeth(Trubyte Biotone) and three high-strength resin teeth(Bioform IPN, Endura, SR-Orthosit-PE) opposing different restorative materials(gold alloys, dental porcelain, composite resin) was compared. Wear tests were conducted with a sliding-induced wear testing apparatus which applied 100,000 strokes to the specimen in a mesio-distal direction under conditions of 100 stroke/min and constant loading of 1Kgf/tooth. Wear resistance of the resin denture teeth was evaluated by the following criteria : 1) wear depth, 2) weight loss, and 3) SEM observation. Results were as follows. 1. When opposed to gold alloys and composite resin, high-strength resin teeth showed superior wear resistance compared to acrylic resin teeth. But, in cases opposing dental porcelain, differences between the wear of the high-strength and acrylic resin teeth were not statistically significant (p<0.05). 2. When comparing wear resistance among high-strength resin teeth, opposing gold alloys, Endura was slightly more resistant and while in cases opposing dental porcelain, SR-Orthosit-PE was showed to be slightly resistant(p<0.05). 3. The wear of high-strength resin teeth was greater by 5 to 7 times when opposing porcelain and 2 to 3 times when opposing composite resin compared to gold alloys(p<0.05). 4. SEM observations of the wear surface showed that wear of resin teeth opposing gold alloys is a fatigue type of wear and wear of resin teeth opposing dental porcelain is fatigue and abrasion type of wear. Trubyte Biotone showed more severe fatigue type of wear than high-strength resin teeth. In conclusion, the use of dental porcelain should seriously be considered as restorative material in cases opposing resin denture teeth and improvement seems to be needed on resin teeth in the areas of wear resistance.