• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.2
• /
• pp.182-188
• /
• 2018

In order to increase the robustness of the uplink for UAS(Unmanned Aerial System), we propose a jamming signal rejection algorithm. In the UAS datalink system, DSSS (direct sequence spread spectrum) is used to reduce the radio noise or jamming signal. In general, jamming signals below the spreading gain are recoverable but the signals beyond the spreading gain can not be recovered. In this paper, these jamming signals beyond spreading gain are detected using the threshold detector in the spectrum area then, generate the estimated signals from the sine wave generator. Finally, we obtain the desired signal to remove jamming signals from the received signals. The proposed scheme can eliminate jamming signals while minimizing the hardware complexity and the original signal loss.

• Journal of the Institute of Convergence Signal Processing
• /
• v.13 no.4
• /
• pp.166-172
• /
• 2012

The standard wave height measurement system is usually based on spectrum analysis for measuring wave height. The spectrum analysis is complicated because of the FFT, and the FFT is not for real time processing since it requires the saved data segments. In this paper, we carried out the performance evaluation of real-time and simpler wave height measurement system using the kalman filter and inertial sensors. The kalman filter theory is complicated, but its algorithm is simpler than the FFT and the kalman filter is used to estimate wave height by integrating acceleration data. But the accumulated error is occurred when the acceleration data is integrated. We developed the algorithm using the wind wave characteristic to decrease the accumulated error. In this paper, the performance evaluation of the wave height measurement system is carried out for various wind wave conditions. Through the experiments, we verified that it shows high measurement performance with the 3.5% margin of error in wind wave condition.

• Asian Journal of Atmospheric Environment
• /
• v.5 no.2
• /
• pp.105-112
• /
• 2011

In order to investigate the effects of local and synoptic meteorological conditions on urban scale particulate air pollutants observed over the Busan coastal area, power spectrum analysis was applied to observed particulate matter with an aerodynamic diameter $\leq10\;{\mu}m$ ($PM_{10}$) for the period from 1 October, 1993 to 31 December, 2004. Fast Fourier Transform (FFT) analysis was used to obtain the hourly mean observed $PM_{10}$ concentrations to identify different periodicity scales of $PM_{10}$ concentrations. The results showed that, aside from the typical and well-known periodicities such as diurnal and annual variations caused by anthropogenic influences, three other significant power spectral density peaks were identified: 7-day, 21-day and 2.25-year periodicities. Cospectrum analysis indicated that the seven-day variations were closely related to the synoptic meteorological conditions such as weak wind speed, which are relevant to the stagnant high pressure system slowly passing through the Korean Peninsula. The intra-seasonal 21-day variation was negatively correlated with wind speed but was consistently positively correlated with relative humidity, which is related to aerosol formation that can be achieved as a result of the hygroscopic characteristics of aerosols. However, the quasibiennial 2.25-year variation was correlated with the frequency of Asian dust occurrence, the periodicities of which have been recorded inter-annually over the Korean Peninsula.

• Korean Journal of Optics and Photonics
• /
• v.13 no.6
• /
• pp.501-505
• /
• 2002

We have numerically analysed the effects of the light sourer spectral power distortion in an optical CDMA system using PN codes and FBGI for ultra-fast multi-access optical networks. The interference between two CDMA channels decreases with an increase in the code length and the .simultaneous access number is equal to the code length in the region of 0 to 15% spectral power distortion. As a result, the spectral power distortion with optical spectrum is very important in designing the optical CDMA systems.

• Journal of the Optical Society of Korea
• /
• v.8 no.4
• /
• pp.174-181
• /
• 2004

Various kinds of systems, that can do target recognition and position detection simultaneously by using infrared sensing detectors, have been developed. In this paper, the detection system TRSS (Thermal target Recognition by Spiral Scanning) adopts linear array shaped uncooled IR detector and uses spiral type fast scanning method for relative position detection of target objects, which radiate an IR region wavelength spectrum. It can detect thermal energy radiating from a 9 m-size target object as far as 200 m distance. And the maximum field of a detector is fully filled with the same size of target object at the minimum approaching distance 50 m. We investigate two types of lens systems. One is a singlet lens and the other is a doublet lens system. Every system includes one aspheric surface and free positioned aperture stop. Many designs of F/1.5 system with ${\pm}5.2^{\circ}$ field at the Efl=20, 30 mm conditions for single element and double elements lens system respectively are compared in their resolution performance [MTF] according to the aspheric surface and stop position changing on their optimization process. Optimum design is established including mechanical boundary conditions and manufacturing considerations.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.1
• /
• pp.43-53
• /
• 1990

The manufacturing errors such as pitch error and run-out error in planetary gear system bring about the irregular displacement of the center of each gear, which cause the torqe variation, vibration and noise. In this study, the relation between manufacturing errors and error motions of the center of gear was analyzed, and it can be applied to identyfy the errors of gears by investigating the measured locus of the center of each gear. Also, another identification method of power spectrum estimation using FFT algorithm was introduced, which analyze the frequency of the measured error motions. The results show that the error of each gear had a corresponding unique frequency, therefore, this method proved to be more effective.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.10
• /
• pp.2187-2193
• /
• 2010

A specific radar system can be implemented more easily using the frequency modulated continuous wave comparing with the pulse Doppler radar. It also has the advantage of LPI (low probability of interception) because of the low power and wide bandwidth characteristics. These radars are usually used to cover the short range area and to obtain the high resolution measurements of the target range and velocity information. The transmitted waveform is used in the mixer to demodulate the received echo signal and the resulting beat signal can be obtained. This beat signal is analyzed using the FFT method for the purpose of clutter removal, detection of a target, extraction of velocity and range information, etc. However, for the case of short signal acquisition time, this FFT method can cause the serious leakage effect which disables the detection of weaker echo signals masked by strong side lobes of the clutter. Therefore, in this paper, the weighting window method is analyzed to suppress the strong side lobes while maintaining the proper main lobe width. Also, the results of FFT beat spectrum analysis are shown under various environments.

• Journal of Power Electronics
• /
• v.9 no.2
• /
• pp.224-231
• /
• 2009

The induction motor rotor fault diagnosis system using current signals, which are measured using an axis-transformation method, is presented in this paper. In inverter-fed motor drives, unlike line-driven motor drives, the stator currents are rich in harmonics; therefore fault diagnosis using stator current is not trivial. The current signals for rotor fault diagnosis need precise and high resolution information, which means the diagnosis system demands additional hardware such as a low pass filter, high resolution ADC, and encoder, etc. The proposed axis-transformation method with encoder and without encoder is expected to contribute to a low cost fault diagnosis system in inverter-fed motor drives without the need for any additional hardware. In order to confirm the validity of the developed algorithms, various experiments for rotor faults are tested and the line current spectrum of each faulty situation using Park transformation is compared with the results obtained from fast Fourier transforms.

• Smart Structures and Systems
• /
• v.13 no.6
• /
• pp.1041-1063
• /
• 2014

This work introduces a two-module robotic pipe inspection system with ultrasonic NDE device to evaluate the integrity of pipe structures. The proposed robotic platform has high mobility. The two module mobile robot platform overcomes pipe obstacle structures such as elbow, or T-branch joints by cooperative maneuvers. Also, it can climb up the straight pipeline at a fast speed due to the wheel driven mechanism. For inspection of pipe structure, SH-waves generated by EMAT are applied with additional signal processing methods. A wavelet transform is implemented to extract a meaningful and specific signal from the superposed SH-wave signals. Intensity ratio which is normalized the defect signals intensity by the maximum intensity of directly transmitted signals in the wavelet transforms spectrum is applied to evaluate defects quantitatively. It is experimentally verified that the robotic ultrasonic inspection system with EMAT is capable of non-destructive inspection and evaluation of defects in pipe structure successfully by applying signal processing method based on wavelet transform.

• Nuclear Engineering and Technology
• /
• v.48 no.1
• /
• pp.189-199
• /
• 2016

Fast neutrons with a broad energy spectrum, with which it is possible to evaluate nuclear data for various research fields such as medical applications and the development of fusion reactors, can be generated by irradiating proton beams on target materials such as beryllium. To generate short-pulse proton beam, we adopted a deflector and slit system. In a simple deflector with slit system, most of the proton beam is blocked by the slit, especially when the beam pulse width is short. Therefore, the available beam current is very low, which results in low neutron flux. In this study, we proposed beam modulation using a buncher cavity to increase the available beam current. The ideal field pattern for the buncher cavity is sawtooth. To make the field pattern similar to a sawtooth waveform, a multiharmonic buncher was adopted. The design process for the multiharmonic buncher includes a beam dynamics calculation and three-dimensional electromagnetic simulation. In addition to the system design for pulsed proton generation, a test bench with a microwave ion source is under preparation to test the performance of the system. The design study results concerning the pulsed proton beam generation and the test bench preparation with some preliminary test results are presented in this paper.