• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.3
• /
• pp.77-84
• /
• 2021

In this study, flexural tests of prestressed high strength spun concrete (PHC) piles reinforced with infilled concrete and longitudinal rebars were conducted, where the longitudinal rebar ratio and the presence of sludge formed on the inner surface of PHC pile were set as key test variables. A total of six PHC pile specimens were manufactured, and their flexural behaviors including failure mode, crack pattern, longitudinal strain distribution in a section and end slip between external PHC pile and infilled concrete were measured and discussed in detail. The test results revealed that the flexural stiffness and strength increased as the longitudinal rebar ratio became larger, and that the sludge formed on the inner surface of PHC pile did not show any detrimental effect on the flexural performance. In addition to the experimental approach, this study presents a nonlinear flexural analysis model considering compatibility conditions and strain and stress distributions of the PHC piles and infilled concrete. The rationality of the nonlinear flexural analysis model was verified by comparing it with test results, and it appeared that the proposed model well evaluated the flexural behavior of PHC piles reinforced with infilled concrete and longitudinal rebars with a good accuracy.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.8
• /
• pp.159-169
• /
• 2007

The behavior of fiber-reinforced cemented sands (FRCS) was studied to improve a brittle failure mode observed in cemented sands. Nak-dong River sand was mixed with ordinary Portland cement and a Polyvinyl alcohol (PVA) fiber. A PVA fiber is widely used in concrete and cement reinforcement. It has a good adhesive property to cement and a specific gravity of 1.3. A PVA fiber has a diameter of 0.1 mm that is thicker than general PVA fiber for reinforced cement. Clean Nak-dong River sand, cement and fiber at optimum water content were compacted in 5 layers giving 55 blows per layer. They were cured for 7 days. Cemented sands with a cement/sand ratio of 4% were fiber-reinforced at different locations and tested for unconfined compression tests. The effect of fiber reinforcement form and distribution on strength was investigated. A specimen with evenly distributed fiber showed two times more strength than not-evenly reinforced specimen. The strength of fiber-reinforced cemented sands increases as fiber reinforcement ratio increases. A fully reinforced specimen was 1.5 times stronger than a specimen reinforced at only middle part. FRCS behavior was controlled not only by a dosage of fiber but also by fiber distribution methods or fiber types.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.2A
• /
• pp.301-310
• /
• 2006

Carbon fiber reinforced polymer (CRFP) materials are well suited to the rehabilitation of civil engineering structures due to their corrosion resistance, high strength to weight ratio and high stiffness to weight ratio. Their application in the field of the rehabilitation of concrete structures is increased due to the vast number of bridges and buildings in need of strengthening. However, RC members, strengthened with externally bonded CFRP plates, happened to collapse before reaching the expected design failure load. Therefore, it is necessary to develop the new strengthening method to overcome the problems of previous bonded strengthening method. This problems can be solved by prestressing the CFRP plate before bonding to the concrete. In this study, a total of 21 specimens of 3.3 m length were tested by the four point bending method after strengthening them with externally bonded CFRP plates. The CFRP plates were bonded without prestress and with various prestress levels ranging from 0.4% to 0.8% of CFRP plate strain. All specimen with end anchorage failed by a plate fracture regardless of the prestress levels while the specimen without end anchorage failed by the separation of the plate from the beam due to premature debonding. The cracking loads was proportionally related to the prestress levels, but the maximum loads of specimens strengthened with prestressed CFRP plates were insignificantly affected by the prestress levels.

• Asia Marketing Journal
• /
• v.15 no.4
• /
• pp.51-60
• /
• 2014

Previous research on loyalty program has verified the factors that influence redemption behavior and the understanding of the mechanism of redemption behavior with academic and practical implications. However, these research has not proven boundary conditions in which the phenomena can be strengthened or weakened- that is, the moderating effect remains unclear. The inclusion of moderating variables can provide a more extensive understanding of the mechanism of this behavior from academic and managerial perspectives alike. Therefore, this current research proposes regulatory focus as a moderating variable, which has received scarce attention in the study of loyalty program behavior, especially individual characteristic variables that, in turn, affect the consumers' purchasing behavior in various ways. Previous research on consumer decision making investigates the differential role of regulatory focus as a series of stages. Regulatory focus theory posits that people depend on the two types of regulatory focus when pursuing goals: promotion focus vs. prevention focus. The former induces tendencies to recognize a goal as a hope and ideal, as something that satisfies the need for accomplishment, and to be sensitive to the presence of a positive outcome of the match and to match the pursuit of goals. On the other hand, the latter tends to regard a goal as the responsibility or obligation to achieve the goal, has a tendency to avoid failure to meet a target, and is sensitive to the presence of the negative consequences that do not reach the target. The following propositions are suggested: 1) The effect of higher accumulation effort level on delaying point redemption speed will be relatively more pronounced for customers with prevention focus. 2) The effect of higher accumulation effort level on large redemption unit size will be relatively more pronounced for customers with prevention focus. 3) The effect of higher accumulation effort level on hedonic redemption ratio will be relatively more pronounced for customers with promotion focus. Therefore, this research provides a moderating variable that has the potential to be used as a reference for market segmentation and affects the relationship between point accumulation effort and three sides of point redemption behavior. On this basis, the direction for the future research on this issue is recommended. Future research could verify these propositions conducting a survey of customers' propensity of regulatory focus in conjunction with the history of the loyalty program of data. This would provide a more realistic effect on the usage behavior of loyalty program consumers by providing useful implications for both marketing practitioners and researchers.

• Journal of Cardiovascular Imaging
• /
• v.30 no.3
• /
• pp.185-196
• /
• 2022

BACKGROUND: Two-dimensional (2D) strain provides more predictive power than ejection fraction (EF) in patients with ST-elevation myocardial infarction (STEMI). 3D strain and EF are also expected to have better clinical usefulness and overcome several inherent limitations of 2D strain. We aimed to clarify the prognostic significance of 3D strain analysis in patients with STEMI. METHODS: Patients who underwent successful revascularization for STEMI were retrospectively recruited. In addition to conventional parameters, 3D EF, global longitudinal strain (GLS), global area strain (GAS), as well as 2D GLS were obtained. We constructed a composite outcome consisting of all-cause death or re-hospitalization for acute heart failure or ventricular arrhythmia. RESULTS: Of 632 STEMI patients, 545 patients (86.2%) had a reliable 3D strain analysis. During median follow-up of 49.5 months, 55 (10.1%) patients experienced the adverse outcome. Left ventricle EF, 2D GLS, 3D EF, 3D GLS, and 3D GAS were significantly associated with poor outcomes. (all, p < 0.001) The maximum likelihood-ratio test was performed to evaluate the additional prognostic value of 2D GLS or 3D GLS over the prognostic model consisting of clinical characteristics and EF, and the likelihood ratio was 15.9 for 2D GLS (p < 0.001) and 1.49 for 3D GLS (p = 0.22). CONCLUSIONS: The predictive power of 3D strain was slightly lower than the 2D strain. Although we can obtain 3D strains, volume, and EF simultaneously in same cycle, the clinical implications of 3D strains in STEMI need to be investigated further.

• Journal of Yeungnam Medical Science
• /
• v.11 no.1
• /
• pp.72-81
• /
• 1994

Total 55 patients with nonsmall cell lung cancer treated with radiation therapy at Department of Therapeutic Radiology, Yeungnam University Hospital, between May-1 1986 and April-30 1993 were retrospectively analyzed by clinical characteristics, failure patterns, follow up duration and survival ratio according to prognostic factors. Obtained results were as follows : 1. Male to female ratio was 17.3 2. Sixth and seventh decades were predominant age group. 3. The patients were 8 in stage I-II, 34 in stage IIIA, 13 in stage IIIb, respectively. 4. Forty five patients out of 55 were squamous cell carcinoma. 5. Primary tumor were originated from upper lobe bronchi predominantly. 6. The size of the primary tumor, lymph node involvement and the degree of differentiation were important in evaluation of prognosis. 7. In conclusion, for patients with poor prognostic factors systemic chemotherapy and multidisciplinary approach were recommended for better treatment outcome and improvement of survival.

• Journal of the East Asian Society of Dietary Life
• /
• v.18 no.1
• /
• pp.72-79
• /
• 2008

This study investigated the changes in textural characteristics that occurred by adding maltose syrup, dextrin, and sucrose to whole egg gels, by assessing coagulation after cooling. It also examined the optimal NaCl and sucrose concentrations for whole egg gels sensory evaluations, and then studied how the addition of sucrose effected gel formation and textural characteristics under optimal NaCl concentration. The additions of maltose syrup, dextrin, and sucrose, presented some color changes. The greater the addition of maltose syrup or dextrin, the lower the L, a, and b values of the whole egg gel and whole egg liquid, and ultimately the color turned dark bluish green. With increasing additions of sucrose, maltose syrup, and dextrin, the viscosity of the whole egg liquid increased slightly. In terms of the mechanical texture characteristic of the gel, the texture was most elastic with the 0.8% addition of sucrose, and hardness decreased by increasing the ratio of added sucrose. Increasing amounts of maltose syrup resulted in less hardness and SF. And for dextrin, the SF increased up to 2.5 and then decreased, and hardness decreased with increasing amounts of dextrin. Based on sensory evaluations, the 0.8% addition of NaCl was significantly preferred(p<0.05), in terms of salty taste. The overall preference scores indicated that the whole egg gel made with 0.3% sucrose and the optimal NaCl concentration(0.8%) was most preferred, and each sample was significant(p<0.05). Under the optimal 0.8% NaCl concentration increasing the sucrose concentration resulted in a darker egg gel color, in terms the L value. SF, NF, and hardness, which are mechanical texture parameters, were when 0.8% sucrose and the optimal NaCl concentration of 0.8% were added to whole egg liquid, in preparing the whole egg gel.

• Journal of Korean Society of Forest Science
• /
• v.89 no.2
• /
• pp.275-284
• /
• 2000

This study was carried out to analyze the mechanical properties of soil and the slope stability on the fill slope of forest road constructed in the regions which consist of igneous and metamorphic rock area. The results were summarized as follows. 1) Soil type by Unified Soil Classification System(USCS) was classified as SW in soil slope, GP in weathered rock slope, GP in soft rock slope for both types of parent rock, but gravelly soil slopes in igneous and metamorphic rock area were classified as SP and GW, respectively. 2) Dry unit weight was $1.34g/cm^2{\sim}1.59g/cm^2$, specific gravity 0.57~0.61, and void ratio 0.66~0.93 in the case of igneous rock area, a dry unit weight was $1.35g/cm^2{\sim}1.51g/cm^2$, specific gravity 2.67~2.77, and void ratio 0.78~1.01 in the case of metamorphic rock area. 3) The strength parameters such as internal friction angle(${\phi}$) and cohesion(c) were selected and tested for slope stability analysis. ${\phi}$ and c of soil in igneous rock area were within the range of $29.51^{\circ}{\sim}41.82^{\circ}$ and $0.03kg/cm^2{\sim}0.38kg/cm^2$, respectively, and $21.43^{\circ}{\sim}41.43^{\circ}$ and $0.05kg/cm^2{\sim}0.44kg/cm^2$ in metamorphic rock area, respectively. 4) Result of the slope stability analysis of forest road showed that, in the weathered rock slope of igneous rock and the weathered rock and soil slope of metamorphic rock area, the possibility of slope failure was high as safety factor was below 1.0.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.3
• /
• pp.47-56
• /
• 2020

In this study, three levels of W/B(Water to Binder) ratio (0.37, 0.42, 0.47) and substitution ratio of GGBFS (Ground Granulated Blast Furnace Slag) rate (0 %, 30 %, 50 %) were considered to perform RCPT (Rapid Chloride Diffusion Test) at the 1,095 aged day. Accelerated chloride diffusion coefficient and passed charge of each concrete mixture were assessed according to Tang's method and ASTM C 1202, and improving behaviors of durability performance with increasing aged days are analyzed based on the test results of previous aged days from the preceding study. As the age of concrete increases, the passed charge and diffusion coefficient have been significantly reduced, and especially the concrete specimens containing GGBFS showed a significantly more reduction than OPC(Ordinary Portland Cement) concrete specimen by latent hydraulic activity. In the case of OPC concrete's results of passed charge, at the 1,095 days, two of them were still in the "Moderate" class. So, if only OPC is used as the binder of concrete, the resistance performance for chloride attack is weak. In this study, the time-parameters (m) were derived based on the results of the accelerated chloride diffusion coefficient, and the deterministic and probabilistic analysis for service life were performed by assuming the design variable as a probability function. For probabilistic service life analysis, durability failure probabilities were calculated using Monte Carlo Simulation (MCS) to evaluate service life. The service life of probabilistic method were lower than that of deterministic method, since the target value of PDF (Probability of Durability Failure) was set very low at 10 %. If the target value of PDF suitable for the purpose of using structure can be set and proper variability can be considered for each design variable, it is believed that more economical durability design can be made.

• Journal of Nutrition and Health
• /
• v.43 no.3
• /
• pp.224-232
• /
• 2010

The prevalence of heart failure (HF) is increasing globally and growing evidence has shown that dietary factors play an important role in preventing and improving prognosis of HF. However, little data on nutrient intake in Korean HF patients which are available to develop dietary guidelines for HF. The aims of this study were to estimate nutrient intake in 78 HF patients and evaluate whether the estimated nutrient intake is appropriate compared to dietary reference intake for Koreans. Data are presented as the ratio of actual intake and estimated average requirement (EAR) for each nutrient. The result showed that the average nutrient intakes including total energy and protein met EAR in total patients. However, the deficiencies in mineral and vitamin intakes were found. Moreover, the proportion of subjects with lower intake than EAR was substantial. The results showed that the proportion of male HF patients with inferior intakes to EAR in calcium, potassium (compared to adequate intake: AI), folate and vitamin $B_{12}$ were 38%, 79%, 38%, and 65%, respectively. Also, the proportion of female HF patients with inferior intakes to EAR in calcium, potassium (compared to AI), folate and vitamin $B_{12}$ were 35%, 88%, 38% and 40%, respectively. In particular, the elderly with HF ($\geq$ 70 yrs, n = 28) showed more serious deficiencies in calcium, potassium (compared to AI), folate and vitamin $B_{12}$. In summary, the intakes of potassium, calcium, folate, and vitamin B12 were not sufficient to meet EAR in HF patients. Furthermore, the proportions of subjects with lower intake than EAR in these nutrients were substantial, raising the possibility that these micronutrients may be involved in the pathogenesis of HF. Practical dietary guideline for HF patients is needed to improve prognosis of HF.