• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.11C
• /
• pp.85-93
• /
• 2001

In this paper, a path restoration method independent of failure location in all-optical networks is proposed and its wavelength requirements are calculated. In the proposed method, since a single backup wavelength is used for any link failure, a node can consist of only fixed wavelength transmitters, resulting in the levels node cost. Hence, restoration process can be triggered just after the failure detection, if combined with edge-disjoint path restoration method. This feature and the parallel cross-connection message transfer technique proposed in this paper make the restoration process faster. Also, it is shown the wavelength requirements in the proposed method are similar to the ones in the method using tunable backup wavelength, resulting in little increment for transmission cost.

• Journal of the Korea Safety Management & Science
• /
• v.16 no.3
• /
• pp.209-218
• /
• 2014

An accident related with elevators can cause death or serious injury of operators or passengers. This kind of a fatal accident is due to a failure of elevator. The reduction of failures of elevators is important to reduce the occurrence of elevator accident. Thus, this paper presents the results of analysis for the failure of elevators using the failure data of elevator. The results of analysis can be used to make a maintenance process of elevators.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1993.04a
• /
• pp.113-118
• /
• 1993

A method for approximating the failure surfaces for columns in compression and biaxial bending was proposed by using the moments along the line of a diagonal of the section. This method showed the better approximations for the failure surfaces of columns than the method of ACI. To calculate the moments along the line of a diagonal of the section, an approximate method which is not influenced by the number of steel s and the location of inner steels was proposed This method gave satisfactory approximations for practical sections of columns.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04b
• /
• pp.677-682
• /
• 1998

Concrete is an inhomogeneous material consisting of larger aggregates and sand embedded in a cement paste matrix. In this study, an acoustic emission technique has been used to clarify the microscope failure mechanisms of concrete under three point bending test. AE source location has also been done to monitor the activities of internal damage and the progress of microscopic failure path during the loading. The relationship between AE characteristic and microscopic and microscopic failure mechanism is discussed.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.05a
• /
• pp.569-570
• /
• 2022

Failure situations occur frequently in the industry, and the existing 2D-based manual for this purpose is not intuitive to understand and it is difficult to immediately interact with maintenance experts. In this paper, we propose a technology that enables workers to perform maintenance in real time with the help of experts without restrictions in time and place based on augmented reality when a failure situation occurs at a remote location. A local virtual human-based expert diagnoses a failure situation based on an adapted panoramic image of a remote failure situation while wearing an HMD headset, and gives instructions to a remote operator. In addition, in an augmented reality (AR) environment in a remote location, for the interaction between the operator and the expert, the HMD's microphone is used to create the expert's hand as well as verbal communication. You can use to point or draw a picture. If this technology is used, it is possible to overcome the limitations of the existing 2D-based manual, and to provide assistance in performing maintenance smoothly remotely even if an expert does not directly visit a remote location.

• Journal of the Korean Wood Science and Technology
• /
• v.18 no.3
• /
• pp.42-52
• /
• 1990

In this study, thick 24mm glulams were composed of thick. 3, 4, 6, 8mm Larch laminas to study that the theoretical analysis and the experimental analysis regarding the location of neutral axis of the glulams were compared, and to study on the effect of location of neutral axis on mechanical properties of glulam. The variation of location of neutral axis after proportional limit(or elastical limit) was studied to offer basic data to make the better composition method of glulam. The result obtained can be summarized as follows: 1. The theoretical neutral axis was 0.547 in solid wood, and also 0.547 in glulams because glulams were composed of only Larch laminas. 2. In solid wood, the deviation of the theoretical and the experimental neutral axis location was 0.1%, But in glulams, the deviation from-12.2% to + 7.8% showed nonuniform pattern but no large deviation. Because laminas was only of Larch and so the mechanical properties of laminas were monotonous. 3. The neutral axis exerted no influance on the elasticity of glulam, which meaned that the maximum shear strength in the neutral axis showed no influance on elasticity limit. 4. The only minutely lower elasticities of glulam than that of solid wood were shown. This was because of influance of glue lines of glulam on the elasticlties. 5. The failure type of glulam was wholly simple tension failure and the horizontal shear failure near neutral axis was not taken place, which was that glue line was complete in bonding and the strength of the lamina was not various but uniform. 6. The ratio of tension strain($^{\varepsilon}t$) I compression strain($^{\varepsilon}c$) initially showed uniform level After the elasticity limit. the ratio was increased with the flow of time and so the tension strain was more increased than compression strain. So this proved tension lamination technique, which is that the mechanical properties of glulam could be improved, if the lamina of more superior strength would he added on the bottom side of the glulam.

• Steel and Composite Structures
• /
• v.50 no.1
• /
• pp.1-13
• /
• 2024

The objective of this research is to study experimentally and numerically the behavior of steel beam columns with openings. Although the presence of openings in the beam columns is inevitable, finding ways to maintain strength is crucial. The studied parameters are opening shape, the ratio between opening height to specimen height, the percentage of opening location from support to beam column length, and web slenderness. Experimental tests are conducted including twelve specimens to study the effect of these parameters and record failure load, load deflection curve, and stress strain curve. Two failure modes are observed: local and flexural buckling. Interaction curves plotted from finite element model analysis are also used to expand the parametric study. Changing the location of the opening can decrease failure load by up to 7% and 60% in both normal and moment ratios respectively. Increasing the opening dimension can lead to a drop in the axial ratio by up to 29% and in the moment ratio by up to 74%. The weakest beam column behavior is noticed in specimens with rectangular openings which results from uneven and concentrated stresses around the opening. The main results of this research illustrate that the best location for opening is at 40% - 50% from beam column support. Also, it is advisable to use circular openings instead of rectangular openings in specimens having slender webs because moment ratios are raised by 85% accompanied by a rise in normal ratios by 9%.

• Journal of the Korea Concrete Institute
• /
• v.13 no.2
• /
• pp.107-113
• /
• 2001

This study was conducted preliminarily to develop the crack source location technique for plain concrete beam using acoustic emission(AE). Before the main experiment, the test of virtual An source location was achieved in plain concrete block. The sensor layout was mutually compared between triangular layout and rectangular layout. As the results of test, AE source location by triangular layout was evaluated more effective than that by rectangular layout. The specimen to apply he source location technique was man in total nine specimens (each three in 40 %, 50%, 60% of W/C ratio) which the experiment variable was the compressive strength level(W/C ratio). The bending loading method is selected by cyclic loadings to evaluate the degree of concrete damage. It is seen that Kaiser effect and Felicity effect exists through analysis of AE parameters in coming failure experiment. As a result of analyzing the felicity ratio(FR) values, it is shown that this values can be used for evaluating the degree of concerto damage. AE activity is started highly at the 70% of failure load without the compressive strength level. Thus considered by a index in constructing the system of the failure warning at application of the field structure. And the results compared the real cracking location with the source location has perceived by AE monitoring before it is appeared the primary crack by visual observation.

• Geomechanics and Engineering
• /
• v.13 no.2
• /
• pp.301-318
• /
• 2017

Based on the existing research results, a three-dimensional failure mechanism of tunnel face was constructed. The dynamic seismic effect was taken into account on the basis of quasi-static method, and the nonlinear Mohr-Coulomb failure criterion was introduced into the limit analysis by using the tangent technique. The collapse pressure along with the failure scope of tunnel face was obtained through nonlinear limit analysis. Results show that nonlinear coefficient and initial cohesion have a significant impact on the collapse pressure and failure zone. However, horizontal seismic coefficient and vertical seismic proportional coefficient merely affect the collapse pressure and the location of failure surface. And their influences on the volume and height of failure mechanism are not obvious. By virtue of reliability theory, the influences of horizontal and vertical seismic forces on supporting pressure were discussed. Meanwhile, safety factors and supporting pressures with respect to 3 different safety levels are also obtained, which may provide references to seismic design of tunnels.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05a
• /
• pp.322-325
• /
• 2006

This study was conducted to develop the crack location technique for CFRP reinforced concrete beam using AE method. To experimentally prove the crack source location made of four reinforced concrete beams strengthened in shear with CFRP. The results compared the real cracking location with the source location has perceived by AE monitoring, before it is appeared the primary crack by visual observation. So, This study used by a basic data in constructing the system of the failure warning at application.