• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.355-359
• /
• 2003

In this paper, we investigated the wear lift, wear rate, and its transition on the Hertz pressure. In the experiment, we used TiAlCrN coating deposited by the sputtering technique and ball diameter of 10mm, 7.94mm and 4.76mm for the various Hertz pressure. Ball-on-disk sliding tests wire performed under the unlubricated condition. As the diameter of a ball decreased, the failure load of TiAlCrN coating decreased. However, a good correlation was observed between the wear life and Hertz pressure, and all ball specimens showed the infinite wear life at about 450MPa. In measurement of wear rate, as the diameter of the ball inclosed, the wear transition appeared in bigger load. However, a good correlation was observed between the wear rate and Hertz pressure. The transition appeared in the range from 550MPa to 600MPa at all ball speimens.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.2 no.2
• /
• pp.131-139
• /
• 1999

An easy and efficient method is proposed for a computation of reliability of preprocessing filters in the fire control system when the sensor data are frequently unreliable depending on the operation environment. It computes state transition probability matrix after modeling filter states as a Markov process, and computing false alarm and detection probability of each filter state under the given sensor failure probability. It shows that two important indices such as distributed state probability and error variance can be derived easily for a reliability assessment of the given sensor fusion system.

• Bulletin of the Korean Chemical Society
• /
• v.19 no.10
• /
• pp.1068-1072
• /
• 1998

We present results of molecular dynamic (MD) simulations for the segmental motion of liquid n-butane as the base case for a consistent study for conformational transition from one rotational isomeric state to another in long chains of liquid n-alkanes. The behavior of the hazard plots for n-butane obtained from our MD simulations are compared with that for n-butane of Brownian dynamics study. The MD results for the conformational transition of n-butane by a Poisson process form the total first passage times are different from those from the separate t-g and g-t first passage times. This poor agreement is probably due to the failure of the detailed balance between the fractions of trans and gauche. The enhancement of the transitions t-g and g-t at short time regions are also discussed.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.10 no.3
• /
• pp.29-36
• /
• 2000

It is very import role to increase communication quality that fast detection of random sequence synchronization fail in synchronous stream cipher system using initial synchronization mode. Generally it sends additional information to detect random sequency synchronization fail. But we can't transmit additional informations to decide synchronization fail in a system using RMVD to correct channel error. In this paper we propose a method to detect synchronization fail in the receiver even though a system using RMVD has no margin to send additional information, For detecting random sequency synchronization fail we decipher receiver data analyze probability of transition rate for pre-determined period and decide synchronization fail using calculated transition rate probability. This proposed method is fast very reliable and robust in noisy channel and is easily implemented with hardware.

• The Journal of Korean Academy of Prosthodontics
• /
• v.28 no.1
• /
• pp.165-191
• /
• 1990

Although a number of studies have been performed to assure that residual stress caused by a mismatch of alloy porcelain thermal expansion can contribute to clinical failure of a ceramometal restoration, the interactive influence of cooling rate on the magnitude of thermal expansion difference and on bond strength between them have not been extensively analyzed. The objective of this study was to determine the influence of cooling rate and the number of firing cycles on the expansion mismatch and the flexural failure resistance of metal porcelain strip. Tested alloys included one Pd-Ag alloy, one Ni-Cr-Be alloy with two kinds of porcelain, Vita and Ceramco. Metal specimens were cast into rods with a height of 13mm and a diameter of 5mm. Subsequently, the castings were subjected to scheduled firing cycles without porcelain. And the porcelain specimens after being fired were trimmed into a bar with a final dimension of $5{\times}5{\times}25mm$. Thermal expansions of the alloys and porcelains were measured by using a push rod or a differential dialometer respecitvely. Porcelain glass transition temperatures and expansion values were derived alloy-porcelain pairs were assessed by comparing expansion values of the components at a porcelain glass transition temperature. Calculations were made using combinations of a Ni-Cr alloy or Pd-Ag alloy with each of two porcelain products. Metal-porcelain strip specimens were subjected to four point loading in an Instron testing machine until crack occured at the metal-cramic interface at the time of sharp decrease of load on recorder. On the basis of this study, the following conclusions may be stated: 1. Regardless of the kinds of ceramometal combinations, both of calculated and experimental data revealed that the double fired specimens exhibited a significantly lower flexural strength. 2. By the rise of the amount of mismatch, bond strength were decreased. 3. Thermal expansion value of Pd-Ag alloys were higher than that of Ni-Cr alloys. 4. Expansion curves of metal were proportional to the increase of temperature and were not affected by the experimental conditions, however porcelains did not show the same magnitude of metal, and a shift of the glass transition temperature to higher temperatures was observed when cooled rapidly 5. Alloy-porcelain thermal compatibility appeared more dependent on the porcelain than the alloy.

• The Journal of Korean Academy of Prosthodontics
• /
• v.29 no.1
• /
• pp.111-137
• /
• 1991

Although a number of studies have been performed to assure that residual stress caused by a mismatch of alloy porcelain thermal expansion can contribute to clinical failure of a ceramometal restoratoin, the interactive influence of cooling rate on the magnitude of thermal expansion difference and on bond strength between them have not been extensively analyzed. The objective of this study was to determine the influence of cooling rate and the number of firing cycles on the expansion mismatch and the flexural failure resistance of metal porcelain strip. Tested alloys included one Pd-Ag alloy, one Ni-Cr-Be alloy with two kinds of porcelain, Vita and Ceramco. Metal specimens were cast into rods with a height of 13mm and a diameter of 5mm. Subsequently, the castings were subjected to scheduled firing cycles without porcelain. And the porcelain specimens after being fired were trimmed into a bar with a final dimension of 5 x 5 x 25mm. Thermal expansions of the alloys and porcelains were measured by using a push rod or a differential dialometer respectively. Porcelain glass transition temperatures and expansion values were derived alloy- porcelain pairs were assessed by comparing expansion values of the components at a porcelain glass transition temperature. Calculations were made using combinations of a Ni-Cr alloy or Pd-Ag alloy with each of two porcelain products. Metal- porcelain strip specimens were subjected to four point loading in an Instron testing machine until crack occured at the metal-cramic interface at the time of sharp decrease of load on recorder. On the basis of this study, the following conclusions may be stated : 1. Regardless of the kinds of ceramometal combinations, both of calculated and experimental data revealed that the double fired specimens exhibited a significantly lower flexural strength. 2. By the rise of the amount of mismatch, bond strength were decreased. 3. Thermal expansion value of Pd-Ag alloys were higher than of Ni-Cr alloys. 4. Expansion curves of metal were proportional to the increase of temperature and were not affected by the experimental conditions, however porcelains did not show the same magnitude of metal, and a shift of the glass transition temperature to higher temperatures was observed when cooled rapidly. 5. Alloy- porcelain thermal compatibility appeared more dependent on the porcelain than the alloy.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.465-466
• /
• 2002

In any mechanical system consisting of gears, shafts and/or bearings, the majority of metallic particles deposited into and carried by the lubrication system originate from the deterioration of oil-wetted working surfaces, even in proper lubrication system, due to failure mechanism (s) such as wear, fatigue and fretting corrosion. Determination of the point at which transition from normal to abnormal or to actual damage occurs has become a focus of attention in research activities for years, because it has been recognized that reliable, economic operation can be achieved through appropriate preventative measures. Known collectively from 'all size wear debris analysis' as early failure detection, the methods of testing for damage differ considerably, range from a micron or a submicron size debris analysis to Magnetic Chip Detector (MCD) ferrous debris analysis. This paper will be focused on the utilization of the low-cost analysis techniques for evaluation of industrial machinery condition.

• International Journal of Reliability and Applications
• /
• v.3 no.3
• /
• pp.147-154
• /
• 2002

In this paper, we consider the warm standby redundant system(WSRS) which is consisted of an active unit, a standby unit and a switchover device. In addition, the switchover processing is controlled by a control module. The effect of failure of the control module is taken into account to develop our reliability model for the redundant structure. For the performance evaluation of a redundant system with the function of switchover processing which is assumed to cause the increase of the failure rate of the system, some reliability indices, such as availability, average availability, reliability and steady state availability, are considered.

• Journal of the Korean Society for Precision Engineering
• /
• v.7 no.2
• /
• pp.113-123
• /
• 1990

To study deleterious effects of contaminants contained in lubricating systems, the effects of fine alumina particle concentration and size on the critical failure load, friction and wear characteristic were examined on boundary lubrication condition using the four ball machine. The following conclusions are deduced: The abrasive is found to cause a transition from mild wear to severe wear at less severe conditions than with clean oil. In mild wear region the friction and wear increase with particle size and concentration, but in severe wear region do not exhibit any definite trend. In relation to film thinckness there is a threshold of particle size beyond which the failure load no longer decreases with particle size.

• Computers and Concrete
• /
• v.16 no.4
• /
• pp.587-604
• /
• 2015

The hybrid-type penalty method (HPM) is suitable for representing failure phenomena occurring during the transition from continua to discontinua in materials such as concrete. Initiation and propagation of dominant cracks and branching of cracks can easily be modeled as a discrete crack. The HPM represents a discrete crack by eliminating the penalty that represents the separation of the elements at the intersection boundary. This treatment is easy because no change in the degrees of freedom for the discrete crack is necessary. In addition, it is important to evaluate the correct deformation of the continua before the crack formation is initiated. To achieve this, we implemented a constitutive model of concrete for the HPM. In this paper, we explain the implemented constitutive model and describe the simulation of an anchor bolt pullout test using the HPM demonstrating its capability for evaluating progressive failure.