• Journal of the Earthquake Engineering Society of Korea
• /
• v.17 no.6
• /
• pp.293-303
• /
• 2013

This paper deals with steel braced frame as increasing the lateral strength and ductility in order to seismic retrofit of existing buildings and discusses the designing criteria and calculation method of retrofitted buildings. The addition of steel braced frame can be effective for increasing the lateral strength and ductility of existing buildings. However, There is a problem in utilizing this method. It is the approach to provide an adequate connection between the existing RC frame and the installed steel braced frame, because global strength by failure mode(three type) depends on detail of connection and strength of existing RC frame. So, the designer must be confirmed if it satisfies the required performance or not. Failure mode of type I is the most appropriate for increasing the lateral strength and ductility. Seismic performance evaluation and strength calculation of seismic retrofit are performed by guideline by KISTEC(Korea Infrastructure Safety & Technology)'s "seismic performance evaluation and rehabilitation of existing buildings" and Japan Building Disaster Prevention Association. Buildings are modeled and non-linear pushover analysis are performed using MIDAS program.

• Journal of Drive and Control
• /
• v.19 no.3
• /
• pp.32-38
• /
• 2022

The in-wheel drive gearbox for military special vehicles converts the high-speed & low-torque output generated by the electric servomotor, into low-speed & high-torque mechanical power. As the vehicle is remotely maneuvered in mountainous terrain, wet fields, rough terrain, etc., the gearbox must generate a maximum input speed exceeding 5,000 rpm, a maximum torque of 245 Nm, and MTBF of 9,600 km. The purpose of this study was to analyze the failure mode of the gearbox, to ensure the durability of the in-wheel drive gearbox. Also, the field load test data of the vehicle was analyzed, the acceleration durability test standards were established, the acceleration durability test was conducted, and the durability test results were analyzed as well.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.10
• /
• pp.1198-1205
• /
• 1999

This study is focused on the reliability evaluation for distribution system based on deterministic evaluation technique. Average failure rates, average outage time, and average annual outage time of electrical parts and load points are calculated through network reduction method and failure mode & effective analysis method. And reliability indices of distribution system are calculated. Finally, by employing analytic hierarchy process method, unique index which evaluates and improves the distribution system is calculated. As a result, finding weak points and expansion schedule of the system is possible. The usefulness of this method is verified by applying it to the Inchon International Airport.

• Journal of Korean Society for Quality Management
• /
• v.40 no.3
• /
• pp.306-315
• /
• 2012

Purpose: To ensure good quality munitions, we require quantitative risk management and optimal risk management of system characteristics. Methods: Failure mode and effects analysis (FMEA) is a widely used technique to assess or to improve reliability of products at early stage of design and development. Traditionally, the prioritization of failures for corrective actions is performed by developing a risk priority number (RPN). Results: This paper reestablishes an effective methodology for prioritization of failure modes in FMEA procedure. Revised evaluation criteria of RPN are devised. Conclusion: To verify the proposed methodology, it is applied to RPN evaluation for K21 infantry combat vehicle.

• Journal of Korean Society for Quality Management
• /
• v.35 no.1
• /
• pp.1-9
• /
• 2007

Failure mode and effects analysis (FMEA) is a widely used technique to assess or to improve reliability of products at early stage of design and development. Traditionally, the prioritization of failures for corrective actions is performed by developing a risk priority number (RPN). In practice, due to insufficient evaluation criteria specific to related product and processes, RPN is not properly evaluated. This paper reestablishes an effective methodology for prioritization of failure modes in FMEA procedure. Revised evaluation criteria of RPN are devised and a refined FMEA sheet is Introduced. To verify the proposed methodology, it is applied to RPN evaluation for motors in household appliances.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.6 s.177
• /
• pp.1565-1574
• /
• 2000

Surface edge crack subjected to contact stresses is analysed. A punch with corner radii is considered to press the semi-infinite plane. Partial slip problem is solved when a shear force is applied to the punch. Dislocation density function method is used to solve the present mixed mode crack problem. The crack length of positive K1 is examined, which is affected by the ratio of the flat portion to the total width of the punch. Surface traction during one cycle of the shear force is evaluated to simulate the fretting condition. The compliance change of the contact surface is also investigated during the shear cycle. It is found that the crack grows during only a part of the cycle, which may be termed as effective period of crack growing. A design method for restraining the fretting failure is discussed, from which recommendable geometry of the punch is suggested.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.38-46
• /
• 2011

Recently railway operators are doing a lot of researches and studies in order to apply reliability technologies to their maintenance tasks. The maintenance in the aviation and the munitions industry has been developed enough to be benchmarked with the high quality reliability technologies; however, railway industry is still situated in a rudimentary stage with insufficient & limited data. 5678 Seoul Metropolitan Rapid Transit Corporation, which has 17 year experience of the EMU maintenance and system development, has made a constant effort for appling RCM (Reliability Centered Maintenance) to the maintenance for a few years. In this connection, the case study is to be introduced. This paper is based on 'RCM Gateway to World Class Maintenance' by Anthony M. Smith". The reliability technology are applied to the specific EMU and its system by 7 stages; accordingly, applying SMRT's maintenance experience, a unique standard for FMEA(failure mode effect analysis) & LTA(logical tree analysis) is established. Moreover, for reasonable and effective preventive maintenance tasks, the case considering an analysis of failure effects is selected in the final step 7. SMRT will develop reliability technologies through the application of the results to all the EMU systems.

• Geomechanics and Engineering
• /
• v.17 no.6
• /
• pp.515-525
• /
• 2019

The calculation of active earth pressure behind retaining wall is a typical three-dimensional (3D) problem with spatial effects. With the help of limit analysis, this paper firstly deduces the internal energy dissipation power equations and various external forces power equations of the 3D retaining wall under the nonlinear strength condition, such as to establish the work-energy balance equation. The pseudo-static method is used to consider the effect of earthquake on active earth pressure in horizontal state. The failure mode is a 3D curvilinear cone failure mechanism. For the different width of the retaining wall, the plane strain block is inserted in the symmetric plane. By optimizing all parameters, the maximum value of active earth pressure is calculated. In order to verify the validity of the new expressions obtained by the paper, the solutions are compared with previously published solutions. Agreement shows that the new expressions are effective. The results of different parameters are given in the forms of figures to analysis the influence caused by nonlinear strength parameters.

• Journal of Korea Multimedia Society
• /
• v.21 no.9
• /
• pp.1099-1109
• /
• 2018

Most of the automotive electronic systems are equipped with control software. ISO 26262 standard has been published to prevent unreasonable risk due to E/E system malfunction. And many automotive companies apply ISO 26262 for safe series product. In ISO 26262 standard, the product quality improves through deductive and inductive safety analysis in all processes including system and software development phase. However, there are few studies on software safety analysis than systems. In the paper, we study the software FMEA(Failure Mode Effect Analysis) technique for product quality of vehicular embedded software. And we propose an effective guideline of software FMEA as EPB industrial practice.

• Composites Research
• /
• v.21 no.1
• /
• pp.22-29
• /
• 2008

This paper presents the evaluation of crashworthiness and rollover characteristics of low-floor bus vehicles made of aluminum honeycomb sandwich composites with glass-fabric epoxy laminate facesheets. Crashworthiness and rollover analysis of low-floor bus was carried out using explicit finite element analysis code LS-DYNA3D with the lapse of time. Material testing was conducted to determine the input parameters for the composite laminate facesheet model, and the effective equivalent damage model for the orthotropic honeycomb core material. The crash conditions of low-floor bus were frontal accident with speed of 60km/h. Rollover analysis were conducted according to the safety rules of European standard (ECE-R66). The results showed that the survival space for driver and passengers was secured against frontal crashworthiness and rollover of low-floor bus. Also, The modified Chang-Chang failure criterion is recommended to predict the failure mode of composite structures for crashworthiness and rollover analysis.