• Transactions of The Korea Fluid Power Systems Society
• /
• v.8 no.3
• /
• pp.1-7
• /
• 2011

As the technologies of electronic device have advanced these days, most of mechanical systems are designed with electronic control unit to take advantage of control parameter adaption to operating conditions and firmware flexibilities as well. On-board diagnosis, which detects the system malfunction and identifies potential source of error with its own diagnostic criteria, and fail-safe that can switch the mode of operation in view of recognized error characteristics enables easy maintenance and troubleshooting as well as system protection. This paper dealt with the development of diagnosis and fail-safe function for proportional flow control valve. All type of errors related to valve control system components are investigated and assigned to a specific hexadecimal codes. Cumulative error detection algorithm is applied in order for the sensitivity and reliability to be appropriate. Embedded simulator which runs simultaneously with system program provides the virtual error simulation environment for expeditious development of error detection algorithm. The diagnosis function was verified both with solenoid valve and embedded simulator test and it will enhance the valve control system monitoring function.

• 한국방재학회:학술대회논문집
• /
• 2008.02a
• /
• pp.485-488
• /
• 2008

The structure supporting road sign is a road information facility for ensuring the safe transportation and smooth traffic. But, lots of road information facilities were damaged by the typhoon "Maemi" in 2003. Such damaged facilities should be rehabilitated and could increase economic loss by causing traffic accident. Therefore, in this study, behavior that reduce wind load and improve wind resistance of the structure supporting road sign are studied about wind load beyond design specification by abnormal climate as below. The first is wind load reducing technique such that shear key resist wind load that is not greater than design wind speed but in case that it is over the design wind limit, column member is rotated on the inner steel pipe axis by the brittle failure of shear key. The second is the technique such that fail-safe the overturning of road sign panel by equipment installation in the vertical member. The third is the technique of installing stiffening plate inside the vertical member to relieve stress concentration.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.7
• /
• pp.3502-3507
• /
• 2013

If a sky-bridge is rigidly connected to adjacent buildings, the irregularity of the connected structures is increased resulting in providing a worse seismic behavior. Therefore, a friction pendulum system (FPS) or lead rubber bearing (LRB) is frequently used for the connection system between a sky-bridge and building structures. These connection systems should be carefully designed to prevent a skyfall of a sky-bridge subjected to severe seismic loads. In this paper, the inevitable structural design procedures for a sky-bridge connection system using a friction pendulum system without uplift resistance capacity have been investigated. To this end, Nuri Dream Square building structure is used as a example structure. The structural design process of a friction pendulum system for fail safe of a sky-bridge has been proposed in this paper by evaluating structural responses of the sky-bridge and building structures subjected to earthquake loads.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.6
• /
• pp.20-26
• /
• 2001

In this paper, we design tunnel inner section displacement measurement system which is composed of potentiometer-type displacement sensors, microcontroller-based intelligent sensing head and host computer for the management system and acquisition data. Multiple node communication bus connects the intelligent sensing heads with the host computer. For safe and re1iab1e network operation we use daisy-chain configuration, termination resistor, fail-safe biasing circuit. For tole enhancement of system utilization, we use modbus protocol. The acquisition data are transmitted to host computer and managed by database. Several data request conditions and sorting conditions are provided by management software. The utilization of designed system is confirmed by experiment.

• 한국기계연구소 소보
• /
• v.4 no.1
• /
• pp.19-26
• /
• 1981

Fatigue, the birth and growth of cracks in metal parts subjected to repeated loading, has been a problem plaguing engineers since the Industrial Revolution and the advent of rotating or reciprocating machinery. Designing against metal fatigue was studied briefly in several aspects. Examples of fatigue failures were shown. Fatigue was classified by loading: uniaxial Fatigue, multiaxial fatigue, cumulative fatigue da¬mage. Fatigue design criteria were discussed: Infinite-Life Design, Safe-Life Design, Fail-Safe Design, and Damage Tolerant Design. Mitigation of notch effects by design, improvement of fatigue strength of metal parts by residual stress and surface finishing were discussed. Relative fatigue beha¬vior was studied under various environmantal conditions. Especially the effects of corrosion, temperature, fretting, and irradiation were covered.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.6
• /
• pp.584-593
• /
• 2012

This paper introduces an AVP (Automated Valet Parking) system which applies an autonomous driving concept into the current PAS (Parking Assistant System). The present commercial PAS technology is limited into vehicle. It means vehicle only senses and controls by and for itself to assist the parking. Therefore, the present PAS is restricted to simple parking events. But AVP includes wider parking events and planning because it uses infra-sensor network as well as vehicle sensor. For the realization of AVP, the commercial steering system of a compact vehicle was modified into steer-by-wire structure and various sensors like LRF (Long Range Finder) and camera were installed in a parking area. And local & global server decides where and when the vehicle can go and park in the testing area after recognized the status of environment and vehicle from those sensors. GPS solution was used to validate the AVP performance. More various parking situations, vehicles and obstacles will be considered in the next research stages based on these results. And we expect this AVP solution with more intelligent vehicles can be applied in a big parking lot like a market, an amusement park, etc.

• Journal of Aerospace System Engineering
• /
• v.13 no.4
• /
• pp.50-59
• /
• 2019

The design of the main control valve, which is the main component of the flap control system, was based on actual manufacturing experience on the basis of trial and error method. In this paper, a model-based part design method is proosed. The flap control system consists of a main control valve, fail-safe valve, solenoid valve, LVDT and force motor. The main control valve consists mainly of a spool and slot. The important design parameters of the main control valve are the slot width, overlap and clearance. AMESim is linked to the model and it analyzes the flow path of the main control valve. Applying the proposed design procedure, it was confirmed that the required performance was satisfied within the allowable machining error range.

• Computational Structural Engineering
• /
• v.7 no.3
• /
• pp.83-93
• /
• 1994

To design and study the dynamic performance of safety structures, crash tests are needed. Method to get the angular accelerations at the time of impact by integating the Euler equations are introduced. Numerically stable 9-array system contains several 7 and 8-array sub-systems in it. Numerical stability of those latent sub-systems are studied using test files. All of the 8-array subsystems were found to be numerically stable. Six of the 7-array sub-systems were stable and other six of the 7-array sub-systems were unstable. Using this findings fail-safe measurement system can be developed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.1
• /
• pp.112-121
• /
• 2016

AFLS (Adaptive front lighting system) is being applied to improve safety in driving automotive at night. Safe embedded system design for controlling head-lamps is required to improve noise robust ECU hardware and software simultaneously by considering safety requirement of hardware-dependent software under severe environmental noise. In this paper, we propose an adaptive headlight controller with a newly-designed symmetric angle sensor compensator, especially based on the proposed steering-swivel angle lookup table to determine whether the current controlling target is safe. The proposed system includes an additional backup hardware to compare the system status and provides safe swivel-angle management using a controlling algorithm based on the pre-defined lookup table (LUT), which is a symmetric mapping relationship between the requested steering angle and expected swivel angle target. The implemented system model shows that the proposed architecture effectively detects abnormal situations and restores safe status of controlling the light-angle in AFLS operations under severe noisy environment.

• Journal of the Korean Society for Railway
• /
• v.10 no.6
• /
• pp.709-716
• /
• 2007

An active steering bogie has been theoretically proved to improve both stability and steering performance remarkably. However, It has not been commercialized yet even though many researchers have been trying to develop it because some technical difficulties still exist such as information acquisition fer active control, increasing mechanical components, high energy consumption, fail-safe problem and so on. To solve those problems, an advanced active steering mechanism is proposed in this paper. With this mechanism, required control force is small enough to use direct drives. Therefore, the number of additional mechanical components can be minimized since mechanical transducers like gears are not necessary. Fail-safe function can be also inserted easily. In this paper, concept design of the proposed active steering bogie is introduced and the possibility is verified through computer simulation using linear dynamic model.