• Journal of computational fluids engineering
• /
• v.6 no.1
• /
• pp.1-13
• /
• 2001

The natural convection heat transfer and solidification in a stratified pool are studied. The flow and heat transfer characteristics in a heat generating pool are compared between single-layered and double-layered pools. And local Nusselt number distributions on outer walls are obtained to consider thermal loads on a vessel wall. The cooling and solidification of Al₂O₃/Fe melt in a hemispherical vessel are simulated to study the mechanism of heat transfer and temperature distribution. A unstructured mesh is chosen for this study because of the non-orthogonality originated from the boundaries of double-layered pool. Interface between the layers is modeled to be fixed. With this assumption mass flux across the interface is neglected, but shear force and heat flux are considered by boundary conditions. The colocated cell-centered finite volume method is used with the Rhie-Chow interpolation to compute cell face velocity. To prevent non-physical solutions near walls in case body force is large the wall pressure is extrapolated by the way to include body force. The numerical solutions calculated by current method show that averaged downward heat flux of the double-layered pool increases compared to single-layered pool and maximum temperature occurs right below the interface of the layers.

• Wind and Structures
• /
• v.5 no.2_3_4
• /
• pp.165-176
• /
• 2002

Results of measurements of surface pressure and of velocity field made on a full-scale 6 m cube in natural wind are reported. Comparisons are made with results from boundary-layer wind-tunnel studies reported in the literature. Two flow angles are reported; flow normal to a face of the cube (the $0^{\circ}$ case) and flow at $45^{\circ}$. In most comparisons, the spread of wind-tunnel results of pressure measurements spans the full-scale measurements. The exception to this is for the $0^{\circ}$ case where the roof and side-wall pressures at full-scale are more negative, and as a result of this the leeward wall pressures are also lower. The cause of this difference is postulated to be a Reynolds Number scale effect that affects flow reattachment. Measurements of velocity in the vicinity of the cube have been used to define the mean reattachment point on the roof centre line for the $0^{\circ}$ case, and the ground level reattachment point behind the cube for both $0^{\circ}$ and $45^{\circ}$ flow. Comparisons are reported with another full-scale experiment and also with wind-tunnel experiments that indicate a possible dependency on turbulence levels in the approach flow.

• Journal of the Korean association of regional geographers
• /
• v.10 no.1
• /
• pp.177-191
• /
• 2004

Monitoring has been done for the shingle beach in Hagdong Beach in Geojesi, City during the seven month period. The shingle beach has been found to go through the cyclic change according to the tidal schedule. The typhoon Rusa in year 2002 affected whole beach face. Sea wall, constructed to protect the village along the beach, aggravates the situation, since it cut off the supply of shingle from the marine terrace, upon which village was built. Concrete walls along the streams also diminish the supply of shingles from the mountains. To protect the shingle beach and encourage the sustainable eco-tourism long-term monitoring on sediment budget is necessary.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.113-120
• /
• 2005

Soil nailing system can be mentioned to a method of supporting as the shear strength of in-situ soils is increased by passive inclusions. In the general soil nailing system, facing walls are used in two kind of a lattice concrete block or a cast in placed concrete wall. A case of lattice concrete blocks is used in slow slopes greater than 1:0.7. Also, a case of a cast in placed concrete wall is used in steep slopes less than 1:0.5. The cast in placed concrete walls are constructed to 30cm thick together with a shotcrete facing. In this study, the assembling soil nailing method as a new soil nailing system is proposed. This method is constructed assembly using precast concrete panels. Therefore ability of the construction and quality of the facings can be modified than a usual soil nailing system. Also, this method can be obtained the effects that a global slope stability increase, as precast concrete panels is put on cutting face after excavating a slope.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.28 no.2
• /
• pp.491-503
• /
• 1998

A cystic compound odontoma in the maxillary sinus occurred in a 13-year-old boy. who had missing right upper third molar without having the history of extraction of the wisdom tooth. He complained nasal stuffiness. headache. and pain on the affected face. resembling any sign and symptoms of the maxillary sinus problems. The cystic compound. sized 2 x 1.5 cm in diameter was pedunculated and attached on the posterior wall of the right maxillary sinus and above the antral floor. The location of the compound odontoma in the maxillary sinus was confirmed after panoramic. waters. spiral tomographic. CT examinations and surgical exploration. Its location was on the medial. posterior. superior to the normal position of the maxillary third molar or the maxillary dental arch. The cystic odontoma in the maxillary sinus made the patient have the signs and symptoms of maxillary sinusitis. The cystic compound odontoma might be originated from the dental lamina of the missing upper right third molar. The 'V principle' of the upper jaw growth and the pneumatization process of the maxillary sinus could explain why the compound odontoma had peduncular shape and the location of odontoma was on the medial. superior to the normal position of the maxillary dental arch.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.2
• /
• pp.50-55
• /
• 2011

A preburner for the high performance, staged combustion cycle liquid rocket engine is being developed. For the structural design processes, strength experiments and finite element analyses on specimens simulating the brazing joints of the preburner, were performed and compared. Total two kinds of the specimen were manufactured for the tests. One simulated the joints between the oxygen injectors and the head junctioned by the conventional vacuum brazing. The another was made to test the brazing surfaces by vacuum compression between the combustion chamber cooling channel and the outer wall. During the burst experiments, it was observed that the fractures were occurred not at the brazed joining but in the middle of the face plate and the cooling wall. In addition, the analysis showed that the predicted fracture locations and the strains were well matched with the experiment results.

• Conservation Science in Museum
• /
• v.12
• /
• pp.53-58
• /
• 2011

This study investigated ingredient of the pigment of wall painting piece of women parade of Gaemachong Goguryo that the National Museum of Korea kept. XRF, a non-destructive analyzer, was used to investigate ingredient of the pigment. At the analysis, not only cinnabar/ vermillion(HgS) but also hematiae(Fe₂O₃) was used to produce red, and carbon was done to produce black, and lead white was done to produce white. The face was painted by mixture of not only cinnabar/ vermillion but also hematiae: No coloring was done depending upon situation.

• Coupled systems mechanics
• /
• v.9 no.3
• /
• pp.289-309
• /
• 2020

The paper studies the fluid flow profile contained between the orthotropic plate and rigid wall under the action of the moving load on the plate and main attention is focused on the fluid velocity profile in the load moving direction. It is assumed that the plate material is orthotropic one and the fluid is viscous and barotropic compressible. The plane-strain state in the plate and the plane flow of the fluid is considered. The motion of the plate is described by utilizing the exact equations of elastodynamics for anisotropic bodies, however, the flow of the fluid by utilizing the linearized Navier-Stokes equations. For the solution of the corresponding boundary value problem, the moving coordinate system associated with the moving load is introduced, after which the exponential Fourier transformation is employed with respect to the coordinate which indicates the distance of the material points from the moving load. The exact analytical expressions for the Fourier transforms of the sought values are obtained, the originals of which are determined numerically. Presented numerical results and their analyses are focused on the question of how the moving load acting on the face plane of the plate which is not in the contact with the fluid can cause the fluid flow and what type profile has this flow along the thickness direction of the strip filled by the fluid and, finally, how this profile changes ahead and behind with the distance of the moving load.

• Proceedings of the Korean Institute of Interior Design Conference
• /
• 2005.05a
• /
• pp.271-272
• /
• 2005

As regards of designing, I chose a simple wall design of repeating pattern of vertical windows, rather than making the building as a glamourous obzet. This kind of approach was intended to pursue strong image of construction company, interchanging and communicating with its confused surrounding. Therefore, I boldly removed parts that I considered needless from the facade, and used simple and easy words clearly implying the organization. Lobby is the face of the building, but since the space is deep and narrow and the reality of lease should be considered, there was limit to give original image to the lobby. Instead, high ceiling is the biggest feature of this space. Doorae Engineering-Construction Corp. is young and energetic company. I wanted to highlight the young and energetic image of the company by crossing tore oblique piece of boards. This doesn't just has a simple function as ceiling, but also work as a major subject in the space. In addition of this powerful space of oblique lines, indirect lighting is used to emphasize the character of territory, continuity and deepness of the space. Character of territory that divides main and supplementary function and main and supplementary moving line is expressed by flow of dimension, and continuity and deepness of space is emphasized by indirect lighting flowing linearly through the crack between the ceiling and the wall.

• Journal of International Society for Simulation Surgery
• /
• v.1 no.1
• /
• pp.7-12
• /
• 2014

Purpose Surgical correction of various occular problems which do not have visual problem in plastic surgical area is to normalize the appearance of the face by restoring the normal position of orbit and eyeball. With development of surgical technique, the orbit can be restored exactly in trauma patient and can be moved totally in hypertelorism, as an example of congenital disease. All these surgeries are based on the hypothesis that the position of oclular glove moves in the plane in a quantitatively predictable reationship to osseous orbit movement. However, no studies have critically evaluated between the change of periorbital soft tissue and the outcome of the surgical correction, because there is no method of objective, quantitave evaluation of the periorbital soft tissue. Method Author suggest the methodology for quantitative assessment of ocular and periocular fat changes using the manipulation of digital images of computed tomographic scan. Results The method was allowed to evaluate inter-dacryon distance, inter-centroid distance, movement of the medial orbital wall, movement of the lateral orbital wall, alteration of thickness of the lateral periorbital fat as indicator of movement of the orbital wall and orbit in the patient with congenital periorbital anomaly and postoperative periorbital surgery. The goal of surgical correction of various occular problems which do not have visual problem in plastic surgical area is to normalize the appearance of the face by restoring the normal position of orbit and eyeball. With development of surgical technique, the orbit can be restored exactly in trauma patient and can be moved totally in hypertelorism, as an example of congenital disease. All these sugeries are based on the hypothesis that the position of oclular glove moves in the plane in a quantitatively predictable relationship to osseous orbit movement. However, no studies have critically evaluated between the change of periorbital soft tissue and the outcome of the surgical correction, because there is no method of objective, quantitave evaluation of the periorbital soft tissue. In this report, author suggest the methodology for quantitative assessment of ocular and periocular fat changes using the manipulation of digital images of computed tomographic scan. Conclusion The method suggested is objective and accurate method in measurement of the orbital contents. It takes time and is not easy to do, however, this kind of measurement for fine structures will be more easily available in near future.