• Geomechanics and Engineering
• /
• v.21 no.2
• /
• pp.215-226
• /
• 2020

The magnitude and distribution of tunnel deformation were widely discussed topics in tunnel engineering. In this paper, a three-dimensional (3D) finite element program was used for the analysis of various horseshoe-shaped opening expressway tunnels under different geologies. Two rock material models - Mohr-Coulomb and Hoek-Brown were executed in the process of analyses; and the results show that the magnitude and distribution of tunnel deformation were close by these two models. The tunnel deformation behaviors were relevant to many factors such as cross-sections and geological conditions; but the geology was the major factor to the normalized longitudinal deformation profile (LDP). If the time-dependent factors were neglected, the maximum displacements were located at the distance of 3 to 4 tunnel diameters behind the excavation face. The ratios of displacement at the excavation face to the maximum displacement were around 1/3 to 1/2. In general, the weaker the rock mass, the larger the ratio. The displacements in front of the excavation face were decreased with the increasement of distance. At the distance of 1.0 to 1.5 tunnel diameter, the displacements were reduced to one-tenth of the maximum displacement.

• Korean Journal of Metals and Materials
• /
• v.48 no.5
• /
• pp.456-461
• /
• 2010

We investigated the In-based ohmic contacts on Nitrogen-face (N-face) n-type GaN, as well as Ga-face n-type GaN, for InGaN-based vertical Light Emitting Diodes (LEDs). For this purpose, we fabricated Circular Transfer Length Method (CTLM) patterns on the N-face n-GaN that were prepared by using a laser-lift off method, as well as on the Ga-face n-GaN that were prepared by using a dry etching method. Then, In/transparent conducting oxide (TCO) and In/TiW schemes were deposited on the CTLM in order for low resistance ohmic contacts to form. The In/TCO scheme on the Ga-face n-GaN showed high specific contact resistance, while the minimum specific contact resistance was only 3${\times}$10$^{-2}$ $\Omega$-cm$^{2}$ after annealing at 300${^{\circ}C}$, which can be attributed to the high sheet resistance of the TCO layer. In contrast, the In/TiW scheme on the Ga-face n-GaN produced low specific contact resistance of 2.1${\times}$10$^{5}$ $\Omega$-cm$^{2}$ after annealing at 500${^{\circ}C}$ for 1 min. In addition, the In/TiW scheme on the N-face n-GaN also resulted in a low specific contact resistance of 2.2${\times}$10$^{-4}$ $\Omega$-cm$^{2}$ after annealing at 300${^{\circ}C}$. These results suggest that both the Ga-face n-GaN and N-face n-GaN.

• Human Ecology Research
• /
• v.51 no.4
• /
• pp.413-424
• /
• 2013

The purpose of this study is to examine the influence of social face sensitivity on vanity and consumption behavior. Questionnaires were administered to 461 college students living in Deagu Metropolitan City and Kyungbook province. Frequency, factor analysis, reliability analysis, regression analysis, and t-test were used for data analysis. Social face sensitivity was categorized into consciousness of being embarrassed, social formality, other consciousness and prestigiousness. Vanity factors were found as physical price, achievement concern, achievement price, and physical concern. Consumption behavior were categorized into 5 factors such as ostentatious consumption, impulsive buying, external information search, brand trust, utilization of internet information and material-oriented. Consciousness of being embarrassed, social formality, and other consciousness, the sub-variables of social face sensitivity had significant effects on achievement concerns and physical concerns. Other consciousness of social face sensitivity had significant effects on all factors of consumption behaviors. There was significant differences in the prestige of social face sensitivity and physical concerns of vanity and ostentatious consumption, impulsive buying, and also in external information search and utilization of internet information of consumer behavior. This indicates that women showed high physical concerns for vanity and ostentatious consumption, impulsive buying, external information search and utilization of internet information of consumption behavior while men care more about prestigiousness of social face sensitivity.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.14-14
• /
• 2006

Homoepitaxial growth of GaN on n-type GaN substrates was carried out by hydride vapor phase epitaxy (HVPE) method. This enables us to reduce or to eliminate the bowing of the GaN substrate caused by thermal mismatch. As a result, the two opposite crystal surfaces have been found to possess low dislocation density. The surface polarity of the homoepitaxially grown GaN was confirmed by both etching of the surface and conversion beam electron diffraction(CBED). The surface morphology and the photoluminescencemeasurement indicated that the surface properties of N-polar face of the homoepitaxlally grown GaN are quite different from the initial N-polar face of the heteroepitaxially grown GaN substrate Also, both surfaces of the GaN substrate were characterized by room temperature Double crystal X-ray diffraction (DCXRD) and photoluminescence measurement.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.3
• /
• pp.245-248
• /
• 2020

The wettability of silicon carbide (SiC) crystal, which has 6H-SiC and 4H-SiC regions prepared using the physical vapor transport (PVT) method, is quantitatively analyzed using dispensed deionized (DI) water droplets. Regardless of the polytypes in SiC, the average of five contact angle measurements showed a difference of about 6° between the Si-face and C-face. The contact angle on the Si-face (C-face) is measured after the removal of the native oxide using BOE (6:1), and revealed a significant decrease of the contact angle from 74.9° (68.4°) to 47.7° (49.3°) and from 75.8° (70.2°) to 51.6° (49.5°) for the 4H-SiC and 6H-SiC regions, respectively. The contact angle of the Si-face recovered over time during room temperature oxidation in air; in contrast, that of the C-face did not recover to the initial value. This study shows that the contact angle is very sensitive to SiC surface polarity, specific surface conditions, and process time. Contact angle measurements are expected to be a rapid way of determining the surface polarity and wettability of SiC crystals.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.790-793
• /
• 2001

The characteristics of smart skin for wireless LAN system under compression load are investigated. The smart skin structure is composed of 3 layers of face material and 2 layers of core material. Theoretical formula for determining buckling load is derived by Rayleigh-Ritz method and compared with experimental result. The maximum length of specimen that buckling does not occur is determined by assuming that the compression load is sustained by only face material. In the experiment, if buckling occurs obviously then it follows the theoretical result well. In the process of buckling, the load supporting capability and the antenna property such as radiation pattern and reflection coefficient were examined.

• Smart Structures and Systems
• /
• v.26 no.2
• /
• pp.185-193
• /
• 2020

Nonlinear vibration of sandwich plate with functionally graded material (FGM) core and carbon nano tubes reinforced (CNTs) nano-composite layers by considering temperature-dependent material properties are studied in this paper. Base on Classical plate theory (CPT), the governing partial differential equations of motion for sandwich plate are derived using Hamilton principle. The Galerkin procedure and multiple scales perturbation method are used to find relation between nonlinear frequency and amplitude of vibration response. The dynamic responses of the sandwich plate are also investigated in both time and frequency domains. Then, the effects of nonlinearity, excitation, power law index of FG core, volume fraction of carbon nanotube, the function of material variations of FG core, temperature changes, scale transformation parameter and damping factor on the frequency responses are investigated.

• Computers and Concrete
• /
• v.24 no.6
• /
• pp.499-511
• /
• 2019

In this paper, wave propagation of double-bonded Cooper-Naghdi micro sandwich cylindrical shells with porous core and carbon nanotube reinforced composite (CNTRC) face sheets are investigated subjected to multi-physical loadings with temperature dependent material properties. The governing equations of motion are derived by Hamilton's principle. Then, the influences of various parameters such as wave number, CNT volume fraction, temperature change, Skempton coefficient, material length scale parameter, porosity coefficient on the phase velocity of double-bonded micro sandwich shell are taken into account. It is seen that by increasing of Skempton coefficient, the phase velocity decreases for higher wave number and the results become approximately the constant. Also, by increasing of the material length scale parameter, the cut of frequency increases, because the stiffness of micro structure increases. The obtained results for this article can be used to detect, locate and quantify crack.

• Structural Engineering and Mechanics
• /
• v.85 no.6
• /
• pp.709-716
• /
• 2023

In this paper, the shape factors of cellular meta-material plates (MMPs) having diverse cell arrays have been determined as the first attempt to finally examine their stability and vibrational frequencies. The MMPs are actually constructed from cylindrical or cubic cellular cores and two face sheets. Sandwich-like MMPs with circular and square holes in the face sheets have been selected in such a way that the effective material properties depend on the cellular architectures. For verifying the frequency results, finite element (FE) simulations are done in Abaqus software. Several graphical results have been represented to explore the effects of cellular architectures on vibrational frequencies and dynamic responses of the MMPs. Also, the deflection-frequency and stability curves in the case of forced vibrations have been plotted for diverse cell arrays.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.527-532
• /
• 2000

The armor composite material targets such as aramid FRMLs with different type and ply number of face material and different type of back-up material, were studied to determine ballistic impact resistance and dynamic failure behavior during ballistic impact. Ballistic impact resistance is determined by $\textrm{V}_{50}$ ballistic limit, a statical velocity with 50% probability for complete penetration, test method. Also dynamic failure behaviors are respectfully observed that result from $\textrm{V}_{50}$ tests. $\textrm{V}_{50}$ tests with $0^{\circ}$ obliquity at room temperature were conducted with projectiles that were able to achieve near or complete penetration during high velocity impact tests. As a result, ballistic impact resistance of anodized Al 5052-H34 alloy(2 ply) is better than that of anodized Al 5052-H34 alloy(1 ply), but Titanium alloy showed the similar ballistic impact resistance. In the face material, ballistic impact resistance of titanium alloy is better than that of anodized Al 5052-H34 alloy. In the back-up material, ballistic impact resistance of T750 type aramid fiber is better than that of CT709 type aramid fiber.