• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.517-519
• /
• 2007

We report our study on the implementation of Q tensor approach into three-dimensional finite element method (FEM) numerical solver. The comparative simulation results demonstrated the possibility of a different director configuration in between Q tensor method and vector method. The comparative study confirmed that Q Tensor implementation is more appropriate for OCB analysis than the vector method.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.163-165
• /
• 1996

In the PIC simulation of plasma, the fields are commonly calculated on uniform spatial grids using FDM. But, FDM has a difficulty in modeling a complex shaped model. FEM has a good flexibiblity in treating a complex shape, so that we calculated the field by using FEM not FDM. In this paper, the plasma between plane-to-plane electrodes was simulated using FEM and FDM. Comparing the results of those two methods told us that FEM is also valid as a calculating method in PIC plasma simulation. In order to verify the use of FEM, the discharge of rod-to-plane was simulated. There was not a little distortion of the electric field between the electrodes due to the distribution of space charges.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.6
• /
• pp.67-72
• /
• 2012

Novel Front End Module(FEM) with improved pedestrian protection is very important to reduce the severity of pedestrian injury. The FEM needs to have enough space from hood to absorb the energy from any pedestrian collision. In this study, the cooling performance of the FEM to cool the engine was investigated under 25% height reduction. The results indicated that the cooling performance analysis was about 86% level compared to that of the conventional FEM. Also, good qualitative agreement between CFD predictions and experimental measurements was found. This FEM needs the cooling performance enhancement for changed air flow path at the frontal part of vehicle. Therefore, we showed an improved performance using air guide setup and shape modification under the high load condition.

• International Journal of Aeronautical and Space Sciences
• /
• v.18 no.1
• /
• pp.63-69
• /
• 2017

In this paper, composite laminate pull-through resistance was analyzed using the FEM method and compared with test results. 2D and 3D simplified FEM models, a nonlinear analysis, and a progressive failure analysis utilizing three composite laminate failure theories Maximum Stress, Maximum Strain, and Tsai-Wu were used to predict the FEM results with the test results. The load and boundary conditions of the test were applied to the FEM to simulate the test. A composite laminate pull-through test (ASTM D7332 Proc. B) was designed with a special fixture to collect more precise data. The test results were compared with the FEM analysis results.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.396-400
• /
• 2003

This paper has studied thermal characteristics of machine tool to develope high speed spindle and optimum design condidering the thermal deformation. Comparing the test data of temperature measurement and structural analysis data using FEM, we verifiedthe test validity and predicted thermal deformation, influence of spindle generation of heat, and established cooling system to prevent the thermal deformation. 1) The temperature rise of spindle system depends on increasing number of rotation and shows sudden doubling increment of number of rotation over 7,000rpm. 2) Oil jacket cooling can be effective cooling method below 8,000rpm but, over 8,000rpm, it shows the decrement of cooling effect. 3) Comparing FEM analysis results and revolution test results, we can confirmn approximate temperature change consequently, it is possible to simulate temperature rise and thermal distribution on the inside of spindle system. 4) We can confirm that simulated approach by FEM analysis can be effective method in thermal-appropriate design..

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.13-14
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.93-94
• /
• 2009

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.2006-2010
• /
• 2005

This study is concerned with the relation between steelbelt and belt edge separation. Belt edge separation causes tire burst and threatens passenger's safety. For that reason, it is important to predict durability caused by belt edge separation first in tire structure design step. In this study, to predict belt edge separation, we suggest the prediction method of belt edge separation and evaluate the effect of steelbelt width on the belt edge separation using FEM. We study on analysis parameter also to do exact estimation about the shear behaviour of belt edge area.

• Journal of the Korean Society of Industry Convergence
• /
• v.10 no.1
• /
• pp.5-14
• /
• 2007

It is necessary for development of drawing product with press to have suitable material selection & all process design and the problem during press process has been cleared from judgement of experience & trial and error. Recently we can estimate press process result from computer aided design & FEM. But we can get more reliable result when we can put more precise process variants during FEM. In case of using a drawbead that is used for the material inflow, it is considered for us to put material property, other analysis condition & friction figure when material is passing through the drawbead for better FEM. From our study, we have drawn an analogy bead connection depth, friction figure & drawing and restraining load according to kinds of lubrication from experiment & FEM for the drawbead. We applied above result to the drawing experiment & FEM and confirmed the validity. We could notice the relation between friction figure & drawing load and the friction figure variation according to kinds of lubrication. It is expected to draw more precise analogy that can be used for real process due to more precise process variants application to FEM.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1985.10a
• /
• pp.27-30
• /
• 1985