• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.10
• /
• pp.5950-5954
• /
• 2014

FEM analysis of cleaning machine was performed. A cleaning machine was designed and measured to develop a cleaning machine with highly improved performance and a real configuration. 3D modeling was conducted using the 3-D design program CATIA V5. In addition, FEM analysis was conducted on the modeled cleaning machine using the ANSYS finite element analysis program and the pressure changes in internal fluid flow were visualized. This result was applied to the new product development of cleaning machines.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.8
• /
• pp.97-102
• /
• 2004

In this paper, a finite element based method far determining factor of safety of slopes which has certain advantages over conventional limit equilibrium methods is described. Particularly, the slope failure behaviour considering different seepage conditions is produced by finite element method using strength reduction technique. It is shown that both the failure mechanism and the safety factor that are analyzed by the FEM using strength reduction technique are an effective means of slope stability analysis. And the stability of a slope with rising water table and rapid drawdown are analyzed and the results are compared with the simplified Bishop Method of the Limit Equilibrium Methods.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.652-658
• /
• 2016

In this paper, the theoretical research and simulation using the Finite Element Method (FEM) to design and form a micro-pattern for an ultrasonic horn is described. The present method is based on an initial design estimate obtained by FEM analysis. The natural and resonant frequencies required for the ultrasonic tool horn used for forming the fine pattern were predicted by finite element analysis. FEM analysis using ANSYS S/W was used to predict the resonant frequency for the optimum technical design of the ultrasonic horn vibration mode shape. When electrical power is supplied to the ultrasonic transducer, it is converted into mechanical movement energy, leading to vibration. The RFID TAG becomes the pattern formed on the insulating sheet by using the longitudinal vibration energy of the ultrasonic tool horn. The FEM analysis result is then incorporated into the optimal design and manufacturing of the ultrasonic tool horn.

• Journal of the Korea Institute of Building Construction
• /
• v.16 no.1
• /
• pp.35-43
• /
• 2016

Concrete is a representative heterogeneous material and mechanical properties of concrete are influenced by various factors. Due to the fact that pores in concrete affect determining compressive strength of concrete, studies which deal with distribution and magnitudes of pores are very important. That way, studies using picture imaging have been emerged. Studies on mechanical performance evaluation of structural lightweight foamed concrete and FEM analysis based on picture image are inadequate because lightweight foamed concrete has been researched for only non-structural. Therefore, in this study, cement paste with foaming agent to evaluate mechanical performance is made, FEM analysis with picture image is conducted and young's modulus of experiment and analysis are compared. In this study, dosage of foaming agent is determined 7 level to check pore distribution and water-binder ratio is determined 20% to progress research about structural light weight foamed concrete. Weight of unit volume is minimum at 0.8% of foaming agent dosage. However, weight of unit volume is increased over 0.8% of foaming agent dosage because of interconnection with independent pores. For FEM analysis, cement paste is photographed to use image analyzer(HF-MA C01). Consequently, the fact that Young's Modulus of experiment and FEM analysis are same is drawn by using OOF(Object Oriented Finite elements).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.11
• /
• pp.6458-6463
• /
• 2014

This study performed FEM analysis of a 38 person elevator brake. Recently, an emergency brake was newly developed to improve elevator safety. A 3D design was developed using Solid Works and FEM analysis using analysis code ANSYS. The total deformation, stress and strain were obtained.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2001.04a
• /
• pp.95-101
• /
• 2001

Steel bridges, which have been damaged by load and corrosion, need repair or strengthening. In general, before the repair welding procedure, cutting procedure carry out. Therefore, the investigating of the behavior of stress generated by cutting is so important for safety of structure. Residual stress produced by gas cutting was analyzed using 2D and 3D thermal elasto-plastic FEM. According to the results, the magnitude of temperature was analyzed by 2D-FEM is smaller than that was analyzed using the 3D-FEM program at the start and end edge of flange. And the magnitude and distribution of residual stress of perpendicular to the cutting line was analyzed by the 2D-FEM program was similar to that was analyzed by the 3B-FEM program. Therefore, it is possible to predict of cutting stress by 2D and 3D FEM.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.2D
• /
• pp.237-245
• /
• 2011

Asphalt Plug Joint(APJ) is a new type of expansion joint that it's application are increased in USA as well as several European countries. APJ's' advantages are cheap construction and maintenance costs, and simple construction and securing of excellent flatness. However, APJ's usability is hindered because it showed a problem of premature failure. Research for solving this problem has been progressed, and FEM analysis among existing researches was peformed. However, the behavior of APJ was insufficiently analyzed and the reliability of the analysis was much low, since the material showing complicated behavior was oversimplified, Therefore, a material model was proposed and its effectiveness was confirmed by comparing it with actual behavior in order to improve the reliability of FEM analysis in this paper. ABAQUS program was used for FEM analysis, and an elasto-plastic model and a viscous-plastic model as the material model of APJ were suggested on the base of experiment results of APJ material performed by Bramel et al. The elasto-plastic model was defined by time-independent analysis since it didn't consider time and strain rate, and the viscous-plastic model was defined by time-dependent analysis since it considered. Influence of various elements affecting the behavior of APJ was investigated, and it was confirmed that the time-dependent analysis showed better result closed to actual behavior than the time-independent analysis.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.8
• /
• pp.71-77
• /
• 2018

In order to estimate behavior of soil mass which is located straight up of reinforced concrete culvert, Ritz method and FEM were applied and arching effects between the soil mass and adjacent soil were considered for the analyses. Analysis results obtained from the Ritz method and finite element method were compared with analytical solution. In the case of estimating nodal forces considered in FEM, caution is needed that shear stress depending on depth from ground surface should be reflected regardless of local coordinate system. Comparing the displacements computed from Ritz method with those of the analytic solution, it is seen that as the power of assumed displacement function increases, differences between the computed displacements and those of analytic solution decreases. It seems that displacements of FEM becomes closer to those of analytical solution as the number of elements are increased. It is seen that stresses computed from the Ritz method don't get closer to those of the analytic solution as the power of assumed displacement function. Stresses from FEM become closer to those of analytic solution as the number of elements are increased. Comparing the analysis results from the Ritz method and FEM with those of analytic solution, it can be seen that FEM is more reliable than Ritz method.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.9
• /
• pp.68-74
• /
• 1998

The ESPI(Electronic Speckle Pattern Interferometry) is a real time, full-field, non-destructive optical measurement technique that allows static and dynamic deformation analysis and surface shape measurements of engineering structures. e .g. turbine blades. vehicle engine components, body panels, etc. This technique is very similar to holographic interferometry, but uses a solid static camera and an image processing board for recording and digital processing of speckle patterns. In this paper it is presented that FEM results for the free vibration of symmetrically laminated composite as [30/-30/90]s. The natural frequencies of laminated composite rectangular plates having the particular boundary condition are experimentally obtained. In order to demonstrate the validity of the experiment, FEM analysis using ANSYS was performed and natural frequencies experimentally obtained is compared with calculation by FEM analysis. The results obtained from both experiment and FEM analysis show a good agreement.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.17 no.4
• /
• pp.365-374
• /
• 2004

Steel bridges, which have been damaged by load and corrosion, need repair or strengthening. That is a cause of decreasing the durability of structure. In order to solve these problems, welding repair and strengthening methods can be considered. In general, cutting and welding procedure is carried out during the repair welding. Therefore, the investigation of the behavior of residual stress and deformation generated by cutting and welding is very important for safety of structure. Residual stress and deformation produced by gas cutting and arc welding were analyzed using 2D and 3D thermal elasto-plastic FEM. According to the results, the magnitude of temperature was analyzed by 2D-FEM is smaller than that was analyzed using the 3D-FEM at the start and end edge of flange. And the magnitude and distribution of residual stress of perpendicular direction of the cutting line and welding line was analyzed by the 2D-FEM was similar to that was analyzed by 3D-FEM. Therefore, it is possible to predict cutting and welding residual stress by 2D and 3D FEM.