• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.399-402
• /
• 1999

In this paper, a new method for calculating capacitance in arbitrarily shape structure is Presented. This new approach based on divergence theorem of Gauss\`s law is acheive by Surface-Contacted Element(SCE) for Gaussian surface. To evaluate accurate capacitance value in nonuniform electric field. in two dimensional analysis the interpolation using the elements which contact one nod (PE: Point-Element) or two nod (FE: Face-Element) is employed. Because the elements contacted with surface are very small compared with total elements in analytic model, SCE method has shorter computing time to calculate capacitance. This proposed method is verified by comparing the simulated results with value obtained by analytic method.

• Geomechanics and Engineering
• /
• 제29권3호
• /
• pp.301-310
• /
• 2022

Accurate prediction of mixed ground conditions ahead of a tunnel face is of vital importance for safe excavation using tunnel boring machines (TBMs). Previous studies have primarily focused on electrical resistivity surveys from the ground surface for geotechnical investigation. In this study, an FE (finite element) numerical model was developed to simulate electrical resistivity surveys for the prediction of risky mixed ground conditions in front of a tunnel face. The proposed FE model is validated by comparing with the apparent electrical resistivity values obtained from the analytical solution corresponding to a vertical fault on the ground surface (i.e., a simplified model). A series of parametric studies was performed with the FE model to analyze the effect of geological and sensor geometric conditions on the electrical resistivity survey. The parametric study revealed that the interface slope between two different ground formations affects the electrical resistivity measurements during TBM excavation. In addition, a large difference in electrical resistivity between two different ground formations represented the dramatic effect of the mixed ground conditions on the electrical resistivity values. The parametric studies of the electrode array showed that the proper selection of the electrode spacing and the location of the electrode array on the tunnel face of TBM is very important. Thus, it is concluded that the developed FE numerical model can successfully predict the presence of a mixed ground zone, which enables optimal management of potential risks.

• Tribology and Lubricants
• /
• 제18권1호
• /
• pp.34-41
• /
• 2002

This paper presents the contact thermal behaviors of mechanical seals depending on the contacting face geometry. Using the finite element analysis, the temperature distribution, thermal distortion and leakage have been analyzed as functions of sealing gap and rotating speed of the seal ring shaft. The FE results indicate that the inclined contacting face may be more effective and stable based on the results of thermal characteristic analysis if the seal ring has been designed with a same thermal capacity between conventional rectangular sealing faces and inclined seating surface of seal rings.

• Advances in nano research
• /
• 제13권2호
• /
• pp.113-120
• /
• 2022

In this paper, a finite element (FE) simulation has been developed in order to examine the nonlinear stability of reinforced sandwich beams with graphene oxide powders (GOPs). In this regard, the nonlinear stability curves have been obtained asuming that the beam is under compressive loads leading to its buckling. The beam is considered to be a three-layered sandwich beam with metal core and GOP reinforced face sheets and it is rested on elastic substrate. Moreover, a higher-order refined beam theory has been considered to formulate the sandwich beam by employing the geometrically perfect and imperfect beam configurations. In the solving procedure, the utalized finite element simulation contains a novel beam element in which shear deformation has been included. The calculated stability curves of GOP-reinforced sandwich beams are shown to be dependent on different parameters such as GOP amount, face sheet thickness, geometrical imperfection and also center deflection.

• Steel and Composite Structures
• /
• 제18권4호
• /
• pp.1001-1021
• /
• 2015

Ultra-lightweight cement composite (ULCC) with a compressive strength of 60 MPa and density of $1,450kg/m^3$ has been developed and used in the steel-concrete-steel (SCS) sandwich structures. This paper investigates the structural performances of SCS sandwich composite beams with ULCC as filled material. Overlapped headed shear studs were used to provide shear and tensile bond between the face plate and the lightweight core. Three-dimensional nonlinear finite element (FE) model was developed for the ultimate strength analysis of such SCS sandwich composite beams. The accuracy of the FE analysis was established by comparing the predicted results with the quasi-static tests on the SCS sandwich beams. The FE model was also applied to the nonlinear analysis on curved SCS sandwich beam and shells and the SCS sandwich beams with J-hook connectors and different concrete core including ULCC, lightweight concrete (LWC) and normal weight concrete (NWC). Validations were also carried out to check the accuracy of the FE analysis on the SCS sandwich beams with J-hook connectors and curved SCS sandwich structure. Finally, recommended FE analysis procedures were given.

• Journal of Mechanical Science and Technology
• /
• 제14권3호
• /
• pp.314-319
• /
• 2000

Back-face strain compliance (BFS compliance) for the four-point bend specimen has been calibrated for various crack length ratios. Finite element technique was employed to simulate four-point loading and calculate back-face strain of the bend specimen. The numerically determined strain variation along the back face indicates that the sensitivity to gage placement increases with crack length and back-face strain at the gage length less than O.2W, where W is the width of the bend specimen, can be measured within 5% deviation of the maximum BFS. Non-dimensional back-face strain compliance, -E'BCW, was calibrated with FE analysis and experiment. The experimentally determined compliance indicates good agreement with the numerical compliance and can be expressed as a function of crack length ratio.

• 소성∙가공
• /
• 제17권6호
• /
• pp.429-435
• /
• 2008

In this paper, the serrated forming process is analyzed with finite element method. The seal should secure the overlapping portions of ligature, which has teeth for ligature to prevent from slipping each other after clamping. In the simulation, rigid-plastic finite element model has been applied to the serration forming process. Serration or teeth forming characteristics has been analyzed numerically in terms of teeth geometry based on different forming conditions. Analyses are focused to find the influence of different die movements and geometries on the tooth geometry, which is crucial for securing overlapping portions of ligature. Two major process variables are selected, which are the face angle and entry angle of punch, respectively. Extensive investigation has been performed to reveal the influences of different entry and face angles on the geometry of teeth formation in the simulation. Three different face angles of punch have been selected to apply to each simulation of serrated sheet forming process with every case of punch entry angles. Furthermore, tooth geometries predicted from simulation have been applied to the indention process for comparing proper tooth geometries to secure the sealing.

• 항공우주기술
• /
• 제9권1호
• /
• pp.9-16
• /
• 2010

본 연구에서는 이전에 구조시험[3]을 실시하였던 압축하중을 받는 샌드위치 패널 시편에 대한 구조 해석을 수행하였다. 구조 해석을 위해 세 가지 방식의 유한요소 모델링을 고려하였으며, 각각의 유한요소 모델을 이용해 선형좌굴해석과 비선형해석을 수행하였다. 이를 통해, 복합재 샌드위치 패널의 압축 좌굴 하중의 정확한 예측을 위해서는 면재는 쉘요소로 심재는 솔리드 요소로 모델링하는 것이 적절함을 확인하였다. 이것은 전체 샌드위치를 쉘요소로 하는 경우, 심재의 국부적인 crushing 효과와 심재의 전단 강성의 영향을 고려할 수 없기 때문이다. 만일 샌드위치 패널이 좌굴 하중 보다 면재의 재료 파손이 더 취약한 경우, 면재의 재료 파손 하중 및 파손 위치의 정확한 예측을 위해서는 샌드위치를 두께 방향으로 한 개의 쉘 요소로 모델링 하는 것이 적절하였다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.204-211
• /
• 2001

For the treatment of high compressibility number in the Reynolds equation, a new class of exponential high-order shape functions has been recently introduced in the literatures. In this paper a FE lubrication analysis method of high speed gas mechanical face seals is developed, implementing these shape functions. Their validity and usefulness are presented using 1-D gas bearing models. And a validation of developed 2-D analysis code is shown with a gas flat and spiral groove face seal models.

• Structural Engineering and Mechanics
• /
• 제85권6호
• /
• pp.709-716
• /
• 2023

In this paper, the shape factors of cellular meta-material plates (MMPs) having diverse cell arrays have been determined as the first attempt to finally examine their stability and vibrational frequencies. The MMPs are actually constructed from cylindrical or cubic cellular cores and two face sheets. Sandwich-like MMPs with circular and square holes in the face sheets have been selected in such a way that the effective material properties depend on the cellular architectures. For verifying the frequency results, finite element (FE) simulations are done in Abaqus software. Several graphical results have been represented to explore the effects of cellular architectures on vibrational frequencies and dynamic responses of the MMPs. Also, the deflection-frequency and stability curves in the case of forced vibrations have been plotted for diverse cell arrays.