• Journal of the Korea Institute of Military Science and Technology
• /
• v.4 no.2
• /
• pp.122-129
• /
• 2001

A characterization procedure for analyzing symmetric coupled MIS(Metal-Insulator-Semiconductor) transmission line is used the same procedure as a general single layer symmetric coupled line with perfect dielectric substrate from the extraction of the characteristic impedance and propagation constant for even- and odd-mode. In this paper, an analysis for a new substrate shielding symmetric coupled MIS structure consisting of grounded crossbar at the interface between Si and SiO2 layer using the Finite- Difference Time-Domain(FDTD) method is presented. In order to reduce the substrate effects on the transmission line characteristics, a shielding structure consisting of grounded crossbar lines over time-domain signal has been examined. Symmetric coupled MIS transmission line parameters for even- and odd-mode are investigated as the functions of frequency, and the extracted distributed frequency- dependent transmission line parameters and corresponding equivalent circuit parameters as well as quality factor for the new MIS crossbar embedded structure are also presented. It is shown that the quality factor of the symmetric coupled transmission line can be improved without significant change in the characteristic impedance and effective dielectric constant.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.6
• /
• pp.253-259
• /
• 2003

In this paper, the scattered field from a Pierson-Moskowitz sea surface assumed as the PEC by the Finite-Difference Time-Domain(FDTD) method was computed. A one-dimensional surface used to analysis scattering was generated by using the Pierson-Moskowitz model. Back scattering coefficients are calculated with different values of the wind speed(U) which determine configuration of the Pierson-Moskowitz sea surface. The number of surface realization for the computed field, the point number, and the width of surface realization are set to be 50, 8192, and 128k, respectively. In order to verify the computed values these results are compared with those of small perturbation methods, which show good agreement between them.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.2
• /
• pp.217-224
• /
• 2002

One of the dominant aspects governing the accuracy of the FDTD method is the size of the spatial increment used in the model. The effect of having reduced cell size is to increase the computational time and memory requirements. To overcome these problems, sub-gridding technique can be used. This implies that the application of a sub-grid cell would provide improved accuracy without increasing the run time and computer resources considerably. In this paper, we describe the three dimensional sub-gridding technique that is applied to model only the fine structure region of interest. The detailed solution procedure is described and some test geometries were solved by both uniform grid and sub-grid models to validate the suggested approach. While keeping the accuracy, the computational time becomes 6 times faster and the memory requirement is reduced by a factor of 2.5 comparing to the conventional FDTD approach.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.9
• /
• pp.1975-1984
• /
• 1997

In this paper, we analyzed the frequency characteristics and the crosstalk of the adjacent parallel lines and the crossed lines in high-speed packaging interconnections by using the three-dimensional finite difference time domain (3D FDTD) method. To analyze the actual crosstalk phenomena in the transmission of the high-speed digital sgnal, the step pulse with fast rise time was used for the source excitation signal instead of using the Gaussian pulse that is generally used in FDTD. To veify the theoretical resutls, the experimental interconnection lines that were fabricated on the Duroid substrate($\varepsilon_{r}$=2.33, h=0.787 [mm]) were tested by TDR(time domain reflectometry). The results show good agreement between the analyzed results and the tested outcomes.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.12
• /
• pp.32-37
• /
• 2000

We proposed to a new method of the aperture coupled microstrip antenna with T-shaped feeding slot. We analyzed method of enhancing the bandwidth of the antenna using FDTD. And the antenna parameters are optimized to get maximum bandwidth. We also calculated the progress process of waves and the distribution of electric field in the time domain. We also calculated return loss, VSWR, input impedance, radiation pattern in the frequency domain by Fourier transforming the time domain results, respectively. It was found that the bandwidth of this antenna changes length and width of the patch, length and width of the slot, length of T-shaped feedline, position of the offset. Measured % bandwidth was 49.2 % in the center frequency 2.5 GHz. These results were in relatively food accordance with calculated values.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.6 no.1
• /
• pp.17-27
• /
• 1995

In this paper, Finite Difference Time Domain (FDTD) method is used to analyze characteristics of the electromagnetically coupled broadband microstrip antenna, and to optimize the antenna parameters. By using short tuning stub in feedline, electromagnetically coupled microstrip antenna shows broadband (approximatcly equal 13%) characteristics, and the characteristics are varied as a function of length, width, and position of the tuning stub. Operating frequency, return loss, VSWR and input impedance are calculated by Fourier transforming the time domain results. Measurement data from fabricated electromagnetically coupled microstrip antenna are compared with FDTD results and are shown to be in good agreement. After optimization of the parameters, maximum bandwidth of about 15% is achieved.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.5
• /
• pp.399-406
• /
• 2019

The variation of ground-penetrating radar(GPR) signal characteristics from dielectric-filled nonmetallic pipes buried in inhomogeneous ground are compared through a numerical simulation. The relative permittivity distribution of the ground is generated by using the continuous random media(CRM) technique. As a function of the relative permittivity of the material filling the nonmetallic pipe buried in the ground media, GPR signals are simulated by using the finite-difference time-domain(FDTD) method. We show that, unlike the case for homogeneous ground, the distortion characteristics of the reflected waves caused by the front convex surface and the rear concave surface of the pipe buried in inhomogeneous ground are different depending on the permittivity contrast between the inside and outside of the pipe.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.5 no.4
• /
• pp.30-39
• /
• 1994

The resonant frequency, reflection cofficient and input impedance of a microstrip transverse dipole coupled electromagnetically are calculated using Finite Difference Time Domain(FDTD) method, and the evolution of gaussian pulse and spatial distribution of electromagnetic field components in the computation domain is represented graphically. Also, we confirmed the computation results show good agreement with the results of Method of Moment(MOM) and experiment[8] reported in the literature.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.1
• /
• pp.42-48
• /
• 2017

Characteristics of ground-penetrating radar(GPR) signals for detecting buried pipes are investigated numerically. Transmitting and receiving parts of a GPR system, a subsurface soil and a plastic pipe filled with a dielectric material are modeled by using the finite-difference time-domain(FDTD) method. FDTD simulations for observing aspects of GPR signals are performed as a function of the diameter of the pipe and the permittivity of the filling material in the pipe. GPR signals scattered by a dielectric filled pipe appear as a superposition of two waves, such as the specular wave from the front convex surface of the pipe and the axial wave from the rear concave surface of the pipe. We show that the amplitude, the polarity, the delay time of two waves depend on the size of the pipe and the permittivity of the filling material in the pipe.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.4
• /
• pp.473-482
• /
• 1998

In this paper, characteristics of the wide band microstrip antennas with parasistic element are analyzed by the Finite Difference Time Domain(FDTD) method, and antenna parameters are optimized to get maximum bandwidth, retern loss, input impedance, and radiation pattern are calculated by Founier transforming the time domain results. The characteristics of the antenna are varied and the bandwidth of the antenna is broaded as a length and a width of the driven element, a gap of the driven element and the parasitic element, a width and a length of parasitic element. So the different patchs are resonating at different frequencies and this multipule resonance increase the bandwidth. The Results of the calculation and measurement, the size of the antenna with parasitic element is about a twice larger than a microstrip antenna, but bandwidth is four times better than a microstrip antenna. And these results were in relatively good accordance with the measured values.