• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 춘계 학술발표대회 개요집
• /
• pp.215-216
• /
• 2004

최근 해양구조물의 수직 칼럼부 용접 공법은 FCAW에 의한 다층 용접으로, 작업 시수와 작업자의 피로 가중 등, 생산 효율면에서 단점이 많았다. 이를 개선하기 위해 최초로 EGW에 의한 단층 용접을 적용하고자 EGW 적용시의 용접강도 및 피로 안전성을 평가하기 위한, 피로 시험을 수행하였다. (중략)

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1996년도 특별강연 및 춘계학술발표 개요집
• /
• pp.176-178
• /
• 1996

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 추계학술발표대회 개요집
• /
• pp.158-161
• /
• 2005

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2007년 추계학술발표대회 개요집
• /
• pp.118-120
• /
• 2007

• Journal of Welding and Joining
• /
• 제18권1호
• /
• pp.83-90
• /
• 2000

It was attempted to improve seam-tracking performance by applying a new arc-sensing algorithm for FCAW(flux-cored arc welding) process in fillet joints. For this study the authors have introduced three different weight factors: $\circled1$ arc currents at the weaving end are more weighted, $\circled2$ arc currents are evenly weighted along the weaving, and $\circled3$ arc currents at the weaving center are more weighted. To evaluate the 3 factors the values of signal-to-noise(S/N) ratio has been measured. The values were obtained for various welding conditions with different gaps in horizontal and vertical fillet joints. The test results showed that the S/N ratio of the 1st case was highest which resulted in the best of seam tracking performance. In addition, the comparison between the seam tracking performance in horizontal fillet joints and that in vertical ones has been done, and the result showed that tracking performance in vertical joints was relatively better than that in horizontal joints.

• Journal of Welding and Joining
• /
• 제13권1호
• /
• pp.127-137
• /
• 1995

The possibility of new GMAW process using economic shielding gases including CO$_{2}$ gas was investigated on the effect of shielding gas on weldabilty. In the optimum welding condition using 600A power source, FCAW process showed low depositions rate, 114 g/min at 300A, but new GMAW using other mixed shielding gases exhibited high deposition rate, 208-224 g/min at 450A. TIME gas, Ar+CO$_{2}$ gas and Ar+CO$_{2}$+O$_{2}$ gas as a shielding gas were able to be used to the very high welding current(450A), moreover TIME gas and Ar+CO$_{2}$ gas showed the highest arc stability among shielding gases studied in this experiments. The weld penetration was performed by axial spray transfer mode of weld droplet. On the basis of workability, weldability and economic point of view, Ar mixture (80%Ar+20%CO$_{2}$) gas was recommended as a shielding gas for the development and application of new GMAW process. This shielding gas showed the low spatter, good weld quality, stable arc and low cost at the region of high welding current.

• 한국생산제조학회지
• /
• 제22권3호
• /
• pp.372-379
• /
• 2013

In this study, we investigated the traits of the clad metals used in hot-rolled clad steel plates. We examined the sensitization and mechanical properties of STS 316 steel plate and carbon steel (A516) under the specific circumstances of post heat treatment and whether a weld was multilayered and thick or repeated because of repairs. The test conditions were as follows. The clad steel plates were butt-welded using FCAW/SAW, and the heat treatment was conducted at $625^{\circ}C$, for 80, 160, 320, 640, or 1280 min. The change in the corrosion resistance was evaluated in these specimens. In the case of the carbon steel (A516), as the heat treatment time increased, the annealing effect caused the tensile strength to decrease. The micro- hardness gradually increased and then decreased after 640 min. The elongation and contraction of the area increased gradually. An oxalic acid etch test and EPR test on STS316, a clad metal, showed a STEP structure and no sensitization. From the test results for the multi-layered and repair welds, it could be concluded that there is no effect on the corrosion resistance of clad metals. In summary, the purpose of this study was to suggest some considerations when developing on-site techniques and evaluate the sensitization of stainless steels.

• 한국해양공학회지
• /
• 제28권6호
• /
• pp.540-545
• /
• 2014

Multipass self-shielded flux cored arc welding with different heat inputs (1.3–2.0 kJ/mm) was conducted to determine the effects of the heat input on the proportion of the reheated region, impact toughness, and diffusible hydrogen content in the weld metal. The reheated region showed twice the impact toughness of the as-deposited region because of its fine grained ferritic-pearlitic microstructure. With decreasing heat input, the proportion of the reheated region in the weld metal became higher, even if the depth of the region became shallower. Accordingly, the greatest impact toughness, 69 J at −40℃, was obtained for the lowest heat input welding, 1.3 kJ/mm. Irrespective of the heat input, little difference was observed in the hardness and diffusible hydrogen content in the weld metal. This result implies that low heat input welding with 1.3 kJ/mm can be performed to obtain a higher proportion of reheated region and thus greater impact toughness for the weld metal without the concern of hydrogen cracking.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.10-10
• /
• 2009

파이프 용접은 중력의 영향으로 인하여 위치에 따라 같은 용접변수라도 비드 형상이 매우 달라 지게 된다. 또한 지금까지 많은 용접 기술자들이 위험하고 까다로운 환경에서 수작업으로 용접을 실행하였다. 따라서 이러한 이유로 용접 자동화 공정이 반드시 필요하게 된다. 본 연구에서는 FCAW를 사용하여 파이프 모재 대신 필릿 평판을 아래보기, 위보기 자세를 포함하여 9개 자세에서 실행하였다. 용접 자세를 비롯한 용접 변수와 비드 형상 변수간의 관계를 비선형 회귀 분석과 구간적 3차 에르미트 보간법을 이용하여 주어진 용접 변수에서의 비드 단면의 형상을 예측하고, 비드의 결함 유무를 파악하였다. 이러한 방법을 통하여 자세에 따라서 용접 결함이 없는 용접 변수를 구할 수 있었다. 시각센서를 이용하여 용접 후 비드 형상에 대해 모니터링을 실시하였다. 모니터링의 알고리즘은 영상획득, 이진화, 세선화, 적응형 미디언 필터링, 적응형 허프 변환, 용접 결함 검출의 순서로 구성되어 있으며, 본 연구에서는 보다 빠른 영상처리를 위하여 적응형 미디언 필터링을 제시하였다. 모니터링을 통하여 2차원 비드 단면뿐만 아니라, 디루니 삼각법을 적용하여 3차원으로 비드 표면을 표현할 수 있다. 보간법을 사용하여 얻은 비드 형상과 시각 센서를 통하여 얻은 비드 형상간의 비교를 통하여 본 연구의 적합성 여부를 확인하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권4호
• /
• pp.399-406
• /
• 2005

Alloy 625 is used widely in industrial applications such as aeronautical aerospace, chemical, petrochemical and marine applications. Because of a good combination of yield strength. tensile strength, creep strength, excellent fabricability, weldability and good resistance to high temperature corrosion on prolonged exposure to aggressive environments. High qualify weldments for this material are readily produced by commonly used processes. But all of processes are not applicable to this material by reason of unavailability of matching, position or suitable welding filler metals and fluxes may limit the choice of welding processes. Recently, the flux cored wire is developed and applied for the better productivity in several welding position including the vortical position. In this study. the weldability and weldment characteristics of Alloy 625 are evaluated in FCAW weld associated with the several shielding gases($80\%Ar+20\%\;CO_2,\;50\%Ar+50\%\;CO_2.\;100\%\;CO_2$) in viewpoint of welding productivity. The results of the experimental study on corrosive characteristics of Alloy 625 are as follows; There is no remarkable difference among shielding gases. however they has a striking difference among corrosive solutions by results of distinguished density and time of corrosive solution. Generally, the shielding gases($80\%Ar+20\%\;CO_2$) was superior to the other gases on high temperature tensile and a low temperature impact. but all of the shield gases were making satisfactory results on corrosion test.