• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 한국축산시설환경학회지
• /
• 제13권2호
• /
• pp.89-96
• /
• 2007

모돈의 산차와 분만후 일령이 비유모돈과 그 자돈들의 행동에 미치는 영향을 조사하기 위하여 산차는 $1{\sim}2$ 산차, $3{\sim}4$ 산차, 5 산차 이상으로 나누고 각각의 산차에 해당하는 모돈이 분만 후 1일, 7일, 14일, 21일이 경과하였을 때 비유모돈과 포유자돈의 행동을 조사하였다. $1{\sim}8$산차 범위의 총 36두의 Landrace 혹은 Yorkshire 순종모돈과 복당 자돈수가 $11{\sim}13$두인 $Landrace\;{\times}\;Yorkshire\;F_1$ 자돈 439두를 공시하여 각 산차와 분만일령에 해당하는 비유 모돈과 그 자돈을 대상으로 24시간 동안의 행동을 각 처리당 3반복으로 비유모돈은 옆으로 누워있는 자세, 엎드린 자세, 앉은 자세, 서 있는 자세, 먹는 동작, 마시는 동작으로 보낸 시간비율을, 포유자돈은 누워 있는 자세, 걸어 다니는 동작, 포유성공, 포유실패로 보낸 시간비율을 분석하였으며 그 결과를 요약하면 다음과 같다. 1. 분만 후 비유기간동안 모돈은 거의 대부분의 시간을 누워서 보내는 것으로 나타났으며, 앉아 있거나 서 있거나 먹고 마시는 동작으로 보내는 시간은 많게는 15%에서 적게는 5% 정도를 차지하는 것으로 조사되었다. 비유기간 동안 모돈의 행동 빈도는 누워있는 자세, 엎드린 자세, 서 있는 자세, 앉아있는 자세, 먹는 동작, 마시는 동작 순으로 많았다. 2. 산차에 따른 비유기간 동안 모돈의 행동은 누워있는 자세와 앉아 있는 자세는 모돈의 산차 간에 차이가 없었으나, 엎드린 자세는 $1{\sim}2$산차 모돈이 가장 낮게 나타났다(P<0.05). 서있는 자세, 먹는 동작, 마시는 동작은 일정한 경향을 나타내지 않았다. 3. 모돈의 비유기간 동안 그 자돈들의 행동은 분만 직후에 누워 있는 비율이 낮고 걷는 동작의 비율이 낮은 반면 포유 성공과 포유 실패가 동시에 높은 경향을 나타내었다. 분만 7일 이후에는 비유기간의 진행에 따른 차이가 없었다. 4. 모돈의 산차에 따른 그 자돈들의 행동은 $1{\sim}2$ 산차 모돈의 자돈들이 누워 있는 시간 비율과 포유 실패가 낮은 경향을 나타내었으나, 3산 이상 모돈의 자돈들은 어떤 행동의 차이도 찾을 수 없었다.

• Journal of Nutrition and Health
• /
• 제29권8호
• /
• pp.889-898
• /
• 1996

인슐린 비의존형 당뇨병환자의 심리적 스트레스와 스트레스호르몬 및 영양상태와의 상과관계를 알아보고자 인슐린 비의존형 당뇨병환자 34명을 대상으로 설문지를 사용하여 직접면접을 통해 심리적 스트레스로 우울, 불안을 측정하였고 24시간 회상법에 의한 영양섭취상태, 에너지 소비량 등을 조사하였고, 공복시 혈액을 채취하여 일반혈액검사에 스트레스호르몬, 아미노산 등을 분석하였다. 우울과 불안은 CED-S와 STAI-S의 방법으로 측정하였고, 영양섭취상태는 전산분석하였다. 그리고 catecholamine, hemoglobin A1C와 아미노산은 HPLC로 분석하였으며 cortisol과 glucagon은 RIA방법으로 분석하였다. 본 연구의 결과, 당뇨병환자의 우울과 불안점수는 대조군에 비해 높았는데 특히 불안은 유의적으로 높았다. 당뇨병환자의 스트레스호르몬을 보면 총 catecholamine은 329.18$\pm$111.49pg/ml이었고 norepinephirne은 233.95$\pm$73.99pg/ml이었으며 epinephrine은 94.03$\pm$75.97pg/ml이었다. Cortisol은 13.18$\pm$5.55ul/ml이었으며 gulcagon은 171.50$\pm$62.50pg/ml이었다. 당뇨병환자의 총 catecholamine, norpinephrine, cortisol 그리고 glucagon 등은 대조군에 비해 유의적으로 높았으며 epinephrine은 높은 경향을 나타냈다. 당뇨병환자의 영양소섭취량은 대조군에 비해 차이가 없었다. 그러나 당뇨병환자의 경우 열량과 칼슘은 권장량보다 적었으나 다른 영양소들은 권장량보다 많이 섭취하였다. 공복혈당, 평상시 공복혈당 (3개월 평균 공복혈당) 그리고 hemoglobin A1C는 각각 184.18$\pm$74.22mg/dl, 177.76$\pm$42.77mg/dl와 8.84$\pm$2.82%이었다. 당뇨병환자의 혈장아미노산의 농도는 일반적으로 정상범위에 속하였다. 당뇨병환자의 불안은 norepinephrine과 평상시 공복혈당과 유의적인 양의 상관관계를 나타내었다. 또한 glucagon, 평상시 공복혈당과 hemoglobin A1C는 분지아미노산 (BCAA, leucine, isoleucine and valine)과 유의적인 양의 상관관계를 나타내었다.

• 핵의학기술
• /
• 제19권1호
• /
• pp.12-16
• /
• 2015

주성분분석(Principal component analysis, PCA)은 고차원 변수들 사이의 복잡한 상관성 구조를 더 낮은 차원으로 단순화하여 상관성의 구조를 쉽게 설명하기 위한 다변량분석기법으로 뇌영상 분석에서 자주 사용되는 방법이다. 주성분분석의 기본개념은 서로 직교하는 변수들의 선형결합을 통해서 원래의 뇌영상 자료가 가지고 있는 전체정보를 최대한 설명할 수 있는 서로 독립적인 새로운 변수들을 유도하는 것이다. 뇌영상분석에서 주성분분석의 효율성과 유용성을 알아보기 위해서 C[11]-PIB 영상을 이용하여 분석하였다. 대상 및 방법으로는 평균나이가 같은 9명의 정상인, 10명의 알츠하이머/경도인지장애환자들의 C[11]-PIB 영상을 이용하였다. PET-CT 장비로는 Biograph 6 Hi-Rez (Siemens-CTI, Knoxville, TN)를 영상을 획득하였고 9.6 MBq/kg C[11]-PIB를 정맥주사 한 후 40분 후에 20분 동안 3D acquisition mode로 방출영상을 얻었다. Attenuation map은 X-ray CT scan을 이용하여 재구성하였다(130 kVp, 240 mA). PIB template을 만들기 위해서 정상인에서 3T MRI T1-weighted 영상을 동시에 얻었다. 주성분분석을 위한전처리과정으로서 공간정규화 및 공간편평화를 SPM8을 이용하여 실시하였고 주성분분석은 Matlab2012b를 이용하여 분석하다. 결과는 주성분분석을 통해서 서로 독립적인 주성분영상들을 얻을 수 있었다. 주성분분석을 통해서 얻어진주성분영상은 C[11]-PIB brain PET 영상의 패턴을 몇 개의 주성분으로 단순화 할 수 있었으며 주로는 neocortex를 변동 나타내는 영상, white matter의 변동을 나타내는 영상 그리고 pons등 deep brain의 변동을 나타내는 영상 등으로 단순화되었다. 결론으로는 주성분분석은 C[11]-PIB brain 영상을 단순화하여 영상의 패턴을 해석하는데 매우 유용하였다. 이러한 주성분분석은C[11]-PIB영상 분석뿐만 아니라 뇌의 포도당 대사를 측정하는 FDG-PET 또는 뇌기능영상등의 다변량분석 방법으로서 그 적용범위가 클 것으로 기대된다.

• 한국식품위생안전성학회지
• /
• 제29권4호
• /
• pp.268-277
• /
• 2014

본 연구는 미나리 수확 후 처리환경의 미생물학적 위해 요소를 조사하기 위해 4개 지역의 미나리 재배농가 9곳을 선정하였다. 미나리 재배농가로부터 다양한 시료를 채취하여 위생지표세균과 병원성 미생물(Escherichia coli O157:H7, Listeria monocytogenes, Staphylococcus aureus and Bacillus cereus)에 대한 오염도를 조사하였다. 먼저, 9개 농가의 재배환경의 미생물 오염도를 분석한 결과 총 호기성 세균과 대장균군이 각각 0~7.00, 0~4.25 log CFU/g, mL, or $100cm^2$ 수준으로 검출되었다. 대장균(E. coli)은 몇몇 농가의 토양, 관개용수, 세척수 및 작업자의 손에서 양성반응을 확인하였으며, 양성반응이 관찰된 농가의 경우 작물인 미나리에서도 양성반응을 보였다. 병원성 미생물 중 B. cereus는 토양에서 가장 많이 검출되었으며, 한 농가의 미나리를 제외한 모든 농가의 세척 후 미나리에서 평균 1.2 log CFU/g수준으로 검출되었다. 황색포도상구균은 세척 후 미나리에서 한 건 정성적으로 검출되었으며, 이외에 다른 병원성 미생물은 관찰되지 않았다. 미나리의 경우 손질 및 세척 후에도 오염도가 유사하거나 오히려 다소 증가하는 경향을 보였다. 이상의 결과 미나리 생산농가의 수확 후 처리 시설 및 작업자에 의해 미생물의 교차 오염 가능성이 있으므로 이에 대한 위생관리를 철저히 해야 한다. 또한, 안전성이 확보된 미나리 생산을 위해서는 GAP와 같은 관리제도의 적용이 필요하다.

• 농업생명과학연구
• /
• 제50권1호
• /
• pp.105-115
• /
• 2016

남부지역의 효율적인 삼나무 임분 관리방안을 마련하기 위하여 20m×20m 규모의 총 67개 조사구를 설치하였으며, 층위별 식생 및 임분구조 조사에 따른 군락유형 및 생장조사를 실시하였다. 군집분석을 실시한 결과 삼나무군락(C1)과 삼나무-편백군락으로 구분되었으며, 삼나무-편백군락은 다시 졸참-곰솔군락(C2), 졸참-편백군락(C3)으로 구분되었다. 교목층 삼나무의 중요치는 C1 97.2%, C2 80.7%, C3 47.6%로 유형간 차이가 나타났으며, 아교목층에는 C1 8.9%, C2 15.2%, C3 5.7%로 C2에서 가장 높게 나타났다. C3의 경우 아교목층에 솜대 및 이대가 나타나 이에 대한 관리가 필요한 것으로 사료된다. 관목층의 경우 C1 9.2%, C2 7.0% 이었으나, C3에서는 삼나무가 나타나지 않았다. 교목층의 종다양도는 C1이 0.059로 가장 낮았으며, C3에서 0.548로 가장 높았다. 우점도는 C1에서 0.958로 나타나 삼나무가 우점하는 것으로 나타났으며, C3은 우점도가 낮게 나타나(0.393) 다수의 종이 경쟁하고 있는 것으로 사료된다. 평균직경연년생장량은 7.01(C2)~8.04(C1)mm/yr의 범위로 나타났으며, 유형별 관리방안은 C1의 경우 경쟁목제거, 가지치기, 솎아베기가 적합하며, C2의 경우 경쟁수종 제거를 통한 삼나무 전형군으로의 유도 및 수하식재를 통한 타 수종으로의 갱신이 더욱 유리할 것으로 판단되었다.

• 한국작물학회지
• /
• 제11권
• /
• pp.81-97
• /
• 1972

논벼농사의 노동력을 덜기 위하여 이중 가장 중요한 호미질에 의한 중경제초의 노력을 살초제에 의한 것으로 전환시키고자 기초적인 면과 실제적인 면으로 시험조사를 하였다. 건국대학교에서 1m평방 안높이 21cm 및 36cm의 두 형의 concrete tank를 각 4개씩 만들고 그 안에 채수관장치를 한 뒤 양토작토로 논벼를 심어 수도물로 관수하고 투수속도와 산소침투 정도와 수량과의 관계를 보았다. 농림부 자재 검사소 내에서 투수가 심한 사질답전포장에 전면적으로 살초제 Stam F-34를 살포하여 제초하고 제 1구는 중경을 하지 않고, 제 2구는 중경 1회, 그리고 제 3구는 중경 2회하여 중경의 효과를 비교하였다. 이리 호남시험장내 건답보통논과 습답에 무중경, 중경 1회 중경 2회의 구와 살초제 Pamcon을 살포한 것들 중, 무중경, 중경 1회 제초 2회, 중경 2회 제초 1회, 중경 3회 제초 2회의 구와 그리고 관행구를 설치하여 중경제초의 비용과 살초제에 의한 비용을 비교하였던바 그 결과를 요약하면 다음과 같다. (1) 투수속도와 산소침투와 수량과의 관계는 일당(24시간당) 투수속도 4cm이상 될 때 지표 2cm하에 산소가 조금 들어가며 3cm보다 적을 때는 산소가 지표하의 매우 옅은 층에만 내려가는 것으로 나타나며 그리고 경심 15cm구에는 일당 투수속도의 0cm(무투수) 1.5cm에서 수량이 많고 2.5cm와 3.4cm에는 감수되며, 경심 30cm구에는 투수속도 1.5cm 및 30cm구에서 수량이 많고 무투수와 투수속도 4cm구에는 수량이 떨어졌다. (2) 투수가 심한 농림부 자재검사소 사질토양에서는 중경의 효과가 없었다. (3) 호남작물시험장내 건답에서는 살초제 Pamcon 처리 무중경구 수량에 대해서 유의성이 보이는 증수구는 없었다. 그리고 습답에서는 무중경구에 있어서 중경제초 및 관행구가 유의성 있게 증수되었다. (4) 논매기 호미질에 의한 10a당 노동력은 정미 37.1시간 식사와 휴식시간 포함하여 53.5시간이고, 노임은 2,346원인데 대하여 살초제 사용에의 한제 초노력은 수동식으로 0.5일 즉 약 5시간 제비용과 감수추정량을 추정할 때 1,130원이고 습답을 제외하면 750원이 되는 것으로 추정 되었다.

• 한국의학물리학회지:의학물리
• /
• 제22권3호
• /
• pp.140-147
• /
• 2011

이 연구에서는 폐종양의 정량적 개선을 위하여 분자체를 이용하여 내부 움직임을 측정하고 평가된 데이터를 기반으로 소동물 PET 영상내의 폐종양을 국소화하고자 하였다. 소동물 폐 영역의 내부 움직임은 방사성물질을 흡착한 분자체를 이용하여 소동물 폐 영역에 부착함으로써 구현하였다. 폐 영역의 내부 움직임 표적으로 사용된 분자체는 약 37 kBq의 Cu-64를 흡착시켜 폐종양을 모사하였다. 소동물 PET 영상은 Siemens Inveon 스캐너를 이용하여 획득하였으며 외부 움직임 데이터는 트리거 생성 장치인 BioVet을 이용하였다. SD-Rat PET 영상은 $^{18}F$-FDG 37 MBq/0.2 mL을 미정맥으로 주사하고 60분 후 20분간 데이터를 획득하였다. 리스트모드 데이터의 각 선응답은 외부 트리거 장치에 의해 획득된 트리거신호를 이용하여 2 bin에서 16 bin으로 사이노그램을 획득하였다. 획득된 사이노그램 데이터는 OSEM 2D 알고리즘을 이용하여 4회의 반복으로 재구성하였다. 종양의 정량적 분석을 위한 PET 영상은 종양을 묘사한 분자체 영역에 관심영역을 설정하고 계수와 SNR 그리고 FWHM을 이용하여 평가하였다. 움직임 표적으로 사용된 분자체의 크기는 $1.59{\times}2.50mm$이었으며, 기준 영상으로 획득한 체외 분자체 수직 및 수평 FWHM은 $2.91{\times}1.43mm$이었다. 정적영상과 4 bin 그리고 8 bin 영상에서의 수직 FWHM은 각각 3.90 mm, 3.74 mm, 3.16 mm이었으며 수평 FWHM은 각각 2.21 mm, 2.06 mm, 1.60 mm이었다. 정적영상, 4 bin, 8 bin, 12 bin 그리고 16 bin의 계수 값은 각각 4.10, 4.83, 5.59, 5.38, 5.31이었다. 정적영상, 4 bin, 8 bin, 12 bin 그리고 16 bin의 SNR은 4.18, 4.05, 4.22, 3.89, 3.58이었다. FWHM은 게이트 수의 증가에 따라 계속 향상됨을 확인하였다. 그러나 계수 값과 SNR은 게이트 수의 증가에 따라 계속 향상되지 않고 특정 bin 수에서 가장 높은 값을 보여 소동물 폐 영역에서의 종양 영상화시 SNR의 손실을 최소화하면서 향상된 계수 값을 얻을 수 있는 게이트 수를 획득하였다. 내부 움직임 측정은 최적화된 종양 국소화 영상을 획득할 수 있으며 외부 움직임 모니터링 시스템을 사용하지 않고 장기별 움직임 예측 모델링을 위한 유용한 방법이 될 것으로 기대된다.

• Journal of the Korean Wood Science and Technology
• /
• 제2권4호
• /
• pp.4-14
• /
• 1974

The total forest land area in Korea accounts for some 67 percent of the nation's land total. Its productivity, however, is very low. Consequently, forest production accounts for only about 2 percent of the gross national product and a minor proportion of no more than about 5 percent versus primary industry. In this case, however, only the direct income from forestry is taken into account, making no reference to the forestry output induced by other industrial sectors. The value added Or the induced forestry output in manufacturing the primary wood products into higher quality products, makes a larger contribution to the economy than direct contribution. So, this author has tried to analyze the structure of forestry and compute the repercussion effect and the induced output of primary forest products when utilized by other industries for their raw materials, Hsing the input-output table and attached tables for 1963 and 1966 issued by the Bank of Korea. 1. Analysis of forestry structure A. Changes in total output Durng the nine-year period, 1961-1969, the real gross national product in Korea increased 2.1 times, while that of primary industries went up about 1. 4 times. Forestry which was valued at 9,380 million won in 1961, was picked up about 2. 1 times to 20, 120 million won in 1969. The rate of the forestry income in the GNP, accordingly, was no more than 1.5 percent both in 1961 and 1962, whereas its rate in primary industries increased 3.5 to 5.4 percent. Such increase in forestry income is attributable to increased forest production and rise in timber prices. The rate of forestry income, nonetheless, was on the decrease on a gradual basis. B. Changes in input coefficient The input coefficient which indicates the inputs of the forest products into other sectors were up in general in 1966 over 1963. It is noted that the input coefficient indicating the amount of forest products supplied to such industries closely related with forestry as lumber and plywood, and wood products and furniture, showed a downward trend for the period 1963-1966. On the other hand, the forest input into other sectors was generally on the increase. Meanwhile, the input coefficient representing the yolume of the forest products supplied to the forestry sector itself showed an upward tendency, which meant more and more decrease in input from other sectors. Generally speaking, in direct proportion to the higher input coefficient in any industrial sector, the reinput coefficient which denotes the use of its products by the same sector becomes higher and higher. C. Changes in ratio of intermediate input The intermediate input ratio showing the dependency on raw materials went up to 15.43 percent m 1966 from 11. 37 percent in 1963. The dependency of forestry on raw materials was no more than 15.43 percent, accounting for a high 83.57 percent of value added. If the intermediate input ratio increases in any given sector, the input coefficient which represents the fe-use of its products by the same sector becomes large. D. Changes in the ratio of intermediate demand The ratio of the intermediate demand represents the characteristics of the intermediary production in each industry, the intermediate demand ratio in forestry which accunted for 69.7 percent in 1963 went up to 75.2 percent in 1966. In other words, forestry is a remarkable industry in that there is characteristics of the intermediary production. E. Changes in import coefficient The import coefficient which denotes the relation between the production activities and imports, recorded at 4.4 percent in 1963, decreased to 2.4 percent in 1966. The ratio of import to total output is not so high. F. Changes in market composition of imported goods One of the major imported goods in the forestry sector is lumber. The import value increased by 60 percent to 667 million won in 1966 from 407 million won in 1963. The sales of imported forest products to two major outlets-lumber and plywood, and wood products and furniture-increased to 343 million won and 31 million won in 1966 from 240million won and 30 million won in 1963 respectively. On the other hand, imported goods valued at 66 million won were sold to the paper products sector in 1963; however, no supply to this sector was recorded in 1963. Besides these major markets, primary industries such as the fishery, coal and agriculture sectors purchase materials from forestry. 2. Analysis of repercussion effect on production The repercussion effect of final demand in any given sector upon the expansion of the production of other sectors was analyzed, using the inverse matrix coefficient tables attached to the the I.O. Table. A. Changes in intra-sector transaction value of inverse matrix coefficient. The intra-sector transaction value of an inverse matrix coefficient represents the extent of an induced increase in the production of self-support products of the same sector, when it is generated directly and indirectly by one unit of final demand in any given sector. The intra-sector transaction value of the forestry sector rose from 1.04 in 1963 to 1, 11 in 1966. It may well be said, therefore, that forestry induces much more self-supporting products in the production of one unit of final demand for forest products. B. Changes in column total of inverse matrix coefficient It should be noted that the column total indicates the degree of effect of the output of the corresponding and related sectors generated by one unit of final demand in each sector. No changes in the column total of the forestry sector were recorded between the 1963 and 1966 figures, both being the same 1. 19. C. Changes in difference between column total and intra-sector transaction amount. The difference between the column total and intra-sector transaction amount by sector reveals the extent of effect of output of related industrial sector induced indirectly by one unit of final demand in corresponding sector. This change in forestry dropped remarkable to 0.08 in 1966 from 0.15 in 1963. Accordingly, the effect of inducement of indirect output of other forestry-related sectors has decreased; this is a really natural phenomenon, as compared with an increasing input coefficient generated by the re-use of forest products by the forestry sector. 3. Induced output of forestry A. Forest products, wood in particular, are supplied to other industries as their raw materials, increasng their value added. In this connection the primary dependency rate on forestry for 1963 and 1966 was compared, i. e., an increase or decrease in each sector, from 7.71 percent in 1963 to 11.91 percent in 1966 in agriculture, 10.32 to 6.11 in fishery, 16.24 to 19.90 in mining, 0.76 to 0.70 in the manufacturing sector and 2.79 to 4.77 percent in the construction sector. Generally speaking, on the average the dependency on forestry during the period 1963-1966 increased from 5.92 percent to 8.03 percent. Accordingly, it may easily be known that the primary forestry output induced by primary and secondary industries increased from 16, 109 million won in 1963 to 48, 842 million won in 1966. B. The forest products are supplied to other industries as their raw materials. The products are processed further into higher quality products. thus indirectly increasing the value of the forest products. The ratio of the increased value added or the secondary dependency on forestry for 1963 and 1966 showed an increase or decrease, from 5.98 percent to 7.87 percent in agriculture, 9.06 to 5.74 in fishery, 13.56 to 15.81 in mining, 0.68 to 0.61 in the manufacturing sector and 2.71 to 4.54 in the construction sector. The average ratio in this connection increased from 4.69 percent to 5.60 percent. In the meantime, the secondary forestry output induced by primary and secondary industries rose from 12,779 million Wall in 1963 to 34,084 million won in 1966. C. The dependency of tertiary industries on forestry showed very minor ratios of 0.46 percent and 0.04 percent in 1963 and 1966 respectively. The forestry output induced by tertiary industry also decreased from 685 million won to 123 million won during the same period. D. Generally speaking, the ratio of dependency on forestry increased from 17.68 percent in 1963 to 24.28 percent in 1966 in primary industries, from 4.69 percent to 5.70 percent in secondary industries, while, as mentioned above, the ratio in the case of tertiary industry decreased from 0.46 to 0.04 percent during the period 1963-66. The mining industry reveals the heaviest rate of dependency on forestry with 29.80 percent in 1963 and 35.71 percent in 1966. As it result, the direct forestry income, valued at 8,172 million won in 1963, shot up to 22,724 million won in 1966. Its composition ratio lo the national income rose from 1.9 percent in 1963 to 2.3 per cent in 1966. If the induced outcome is taken into account, the total forestry production which was estimated at 37,744 million won in 1963 picked up to 105,773 million won in 1966, about 4.5 times its direct income. It is further noted that the ratio of the gross forestry product to the gross national product. rose significantly from 8.8 percent in 1963 to 10.7 percent in 1966. E. In computing the above mentioned ratio not taken into consideration were such intangible, indirect effects as the drought and flood prevention, check of soil run-off, watershed and land conservation, improvement of the people's recreational and emotional living, and maintenance and increase in the national health and sanitation. F. In conclusion, I would like to emphasize that the forestry sector exercices an important effect upon the national economy and that the effect of induced forestry output is greater than its direct income.

• Clinical and Experimental Pediatrics
• /
• 제45권2호
• /
• pp.174-182
• /
• 2002

목 적 : 경제발전과 더불어 영양과잉이 문제되고 있으며 비만한 소아가 매년 증가되고 있는 추세이다. 저자들은 인천의 도시와 농촌 지역을 대상으로 중고생 및 대학생을 대상으로 비만 및 체중미달의 유병율을 알아보고 비만도와 콜레스테롤과의 관계를 조사하여 이를 근거로 청소년기의 영양상태를 알아보고자 하였다. 방 법 : 2000년 4, 5월 인천지역의 3개의 중학교, 5개의 고등학교, 인하대학교 여대생 총 1,456명(남 : 여=685 : 771)을 대상으로 신체계측과 함께, 혈청 콜레스테롤치를 측정하였으며, 설문조사를 통해 영양섭취상태를 조사하였으며, 1998년 대한소아과학회에서 측정한 한국 소아 및 청소년의 신장별 체중 백분위의 50퍼센타일 값을 표준체중으로 하여 비만도를 측정하여, 20% 이상을 비만, -10% 이하를 체중 미달로 정하였고, 또한 1998년 대한 소아과 학회에서 제정한 각 연령별 체질량지수를 근거로 95 백분위수 이상을 비만으로 정하고 15 백분위수 미만을 체중미달로 정하였다. 결 과 : 1) 청소년 비만도의 분포를 정상, 비만, 체중미달로 구분하였을 때, 남자에서는 각각 60.7%, 12.1%, 27.2%이었으며, 여자에서는 각각 70.9%, 11.3%, 17.8%로 남녀 분포의 유의한 차이가 있었다(P=0.001). 2) 표준체중에 의한 비만 유병율은 11.7%(남 : 여=12.1 : 11.3)였고, 이 중 경도비만이 6.5%(남 : 여=6.7 :6.4), 중등도 비만 4.6%(남 : 여=4.4 : 4.8), 고도비만은 0.5%(남 : 여=1.0 : 0.1)였고, 체질량지수에 의한 비만 유병율은 남녀 각각 6.4%, 6.2%였다. 3) 남자에서 농촌 지역의 비만과 체중미달 유병율은 각각 8.5%, 34.1%였고, 도시 지역은 각각 14.3%, 22.9%로 분포의 유의한 차이가 있었다(P=0.002). 여자에서 농촌 지역의 비만과 체중미달 유병율은 각각 12.5%, 19.6%였고, 도시 지역은 각각 10.5%, 16.6%로 두 지역의 체중 분포의 유의한 차이는 없었다(P=0.529). 4) 연령별 비만 유병율은 나이가 많아지면서 증가하다가 16세에 16.3%(남자 15.8%, 여자 16.8%)로 가 장 많은 분포를 차지하고 그 이후로 감소하였다. 체중 미달의 연령별 유병율은 남자가 14세에 39.4%, 여자가 12세에 53.2%로 가장 많은 분포를 보였다. 5) 인문계, 실업계 남자에서 비만 유병율은 각각 13.7%, 9.7%로 인문계에서 더 많은 분포를 차지하였으나 통계학적인 차이는 없었고(P=0.116), 여자는 각각 6.8%, 18.0%로 실업계에 비만 청소년이 더 많은 분포를 차지하여 통계학적인 차이가 있었다(P=0.001). 6) 혈청 콜레스테롤치 200 mg/dL 이상은 비만 청소년에서 6.2%, 170-200 mg/dL인 경우는 비만군에서 22.2%로 비 비만군에 비해 높았고 서로 유의한 상관 관계를 가지고 있었다(r=0.111). 결 론 : 인천지역의 청소년 비만은 조사자의 약 12%로 적지 않음을 알 수 있으며 반면 체중미달도 적지 않은 것을 알 수 있었다. 따라서 청소년 영양에 대해 관심과 체계적인 교육이 필요하다고 사료되며 그리하여 성인병을 예방하고 한편 영양불량을 개선하는 것이 시급한 문제로 생각된다.