• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.1
• /
• pp.85-94
• /
• 2014

Tolerance accumulation has serious effect on the performance of an assembled body. This paper proposes the method which analyzes tolerance accumulation using Monte Carlo Simulation. This method can predict tolerance distribution of fully assembled body using the dimensional tolerance distribution of each part to be assembled. In this analysis, it is assumed that the tolerance of each part has the nominal distribution or uniform distribution. This analysis method is applied to ECV(External Control Valve), and the accumulated tolerance of the fully assembled ECV is obtained from the analysis. The results show that initial tolerance given to each part do not meet the design requirement of ECV. Hence, the tolerances of each part are modified and the additional analysis with the modified tolerances yields the results which satisfy the design requirements of ECV.

• Journal of Biomedical Engineering Research
• /
• v.13 no.4
• /
• pp.285-298
• /
• 1992

An analysis of the dynamics in the closing phase of the occluder of a mechanical monoleaflet heart valve prosthesis is presented. The dynamic analysis of the fluid in the vicinity of the occluder was based on the control vo]use approach. The backflow velocity of the fluid was computed by applying the continuity, Bernoulli's and momentum equations in the unsteady state. By considering the fluid pressure and gravity as external forces acting on the occluder, the moment equilibrium on fine occluder was employed to analyze the motion of the occluder during closing and the force of impact between the occluder and the guiding struts. Occluder comes to rest after several oscillations in about 10-18 msec after the Inltiaton of closing. As the aortic pressure increases, the occludes closes faster and comes to the final resting position earlier and the impact force increases also. But backflow is not af footed by the variation of the aortic pressure. With decreasing time delay of the ventricle pressure, the occluder closes faster and impact force Increases. The computed magnitudes of the occluder tiP velocities as well as the backflow of the fluid during the closing phase using this model were in agreement with previously reported experimental measurements.

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.4
• /
• pp.320-326
• /
• 2000

The real-time simulator of a pneumatic actuation system that is composed of differential PWM signal generator, charge solenoid valve, discharge solenoid valve, actuator, load, and rotational potentiometer is developed using a DSP board and a PC. The simulator receives the control signals from the external controller through the A/D converter, updates the state and output variables of the Pneumatic actuation system responding to the input signals every sampling time, and sends out the output signals through the D/A converter in real time. The user can observe the displacements, velocities, pressures, and mass flows representing the operation of pneumatic actuation system through the PC monitor in real time. Also the user can see the moving images between the pistons and rotating arm realistically in real time. The accuracy of the real-time simulator is verified by the good agreement of the real-time simulation results and the experimental results of the pneumatic actuation system.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.2
• /
• pp.90-96
• /
• 2008

A pneumatic system was proposed to evaluate displacement accuracy of the pneumatic actuator without external load and to analyze capability of integration of the proposed valve system. The proposed pneumatic system consisted of a combination of pneumatic valves, two proximity sensors, and a programmable logic controller(PLC). The position controller is based on the PLC controller connected with the proximity sensors. Displacement accuracy of the pneumatic cylinder stroke was tested by varying air pressures of the supply and discharge-side and strokes of the pneumatic cylinder. The displacement accuracy of the pneumatic cylinder stroke increased as the supply and discharge side of air pressure increased at the stroke length of 133mm. Also the displacement accuracy increased as the stroke length increased with a fixed supply and discharge side of air pressure of the pneumatic cylinder as 3.5 and $4.5kg/cm^2$, respectively. The most accurate displacement of the pneumatic cylinder(i.e., standard deviation of 0.01 mm) was obtained at the supply and discharge side of air pressure of 4.0 and $5.0kg/cm^2$, respectively, and strokes of 170 and 190 mm among arbitrarily selected supply and discharge side air pressures and strokes.

• The Korean Journal of Malacology
• /
• v.9 no.1
• /
• pp.46-62
• /
• 1993

Six species of freshx\water Unionidae mussels in Korea, Anodonta arcaeformis flavotincta, A. woodiana, Unio douglasiae, U. douglasiae sinuloatus, Lamprotula gottschei, Lanceolaria acorohyncha were compared in regard to the various taxonomical characteristics of ultra structures of shells and glochidia. The results obtained in this study are summarized as follows;the orter demibranchs of all the females of six species have served as marsupial(gravid)pouch. However, all the foru demibranchs were used as the marsupium in some female individuals of L. gottschei. The glochidia of A. arcaeformis flavotincta, A. woodiana and L. gottschei were separated one by one with the mucous strings and U. douglasiae sinuolatus were round-subtriangular in shape, and those of L. gottschei were subelliptical in shape. Each of the glochidial shell valves of six species had a hook studded with many spines on the superior face on valve. The glochidial shell valve had two or three rows of large spines; A. arcaeformis flavotincta, A. woodiana, and L. gottschei had two rows and three rows in U. douglasiae, U. douglasiae sinuolatus, and L. acrorhyncha. The numbers of sensory hairs of A. arcaeformis flavotincta and A. woodiana were all eight, those of U. douglasiae, U. douglasiae sinuolatus and L. acrorhyncha were six. and that of L. gottschei was four. The external and internal surfaces of the glochidial shell valves of A. A. arcadformis flavotincta, A. woodiana, and L. gottschei had foveolate and psilate in U. douglaseae, U. douglasiae sinuolatus and L. acrorhyncha.

• Journal of the Korean Society of Safety
• /
• v.30 no.6
• /
• pp.48-55
• /
• 2015

A variety of safety issues were investigated for chemical reactors using a toluene solvent in case of a fire at small to middle scale chemical plants. The issues covered the operation of pressure-relieving valves and the subsequent discharges of the toluene to the atmosphere either directly or through an absorber, which represent the current practice at most small chemical plants. It was shown that the safety valve on the reactor may not operate within about twenty minutes after an external fire breaks out, but, once relieved, the toluene vapor released directly to the atmosphere may form a large explosion range on the ground. It was also shown that if the discharge is routed to an existing absorber used for the scrubbing of volatile organic compounds or dusts, the column may not operate normally due to excessive pressure drops or flooding, resulting in the hazardous release of toluene vapors. This study proposed two ways of alleviating these risks. The first is to ruduce the discharge itself from the safety valve by using adequate insulation and protection covers on the reactor and then introduce it into the circulation water at the bottom of the absorber through a dip linet pipe equipped with a ring-shaped sparger. This will enhance the condensation of toluene vapors with the reduced effluent vapors treated in the packing layers above. The second is to install a separate quench drum to condense the routed toluene vapors more effectively than the existing absorber.

• The Korean Journal of Malacology
• /
• v.5 no.1
• /
• pp.1-9
• /
• 1989

A scanning electron microscopic study on the glochidium and glchidial encystment of Anodonta grandis on the guppy was conducted. The shape of the glochidium is apparently triangular and its averge size is 0.45mm X0.4mm when closed, The two glochidial shell valves are of the same size, kept together by a ligament of 120${\mu}{\textrm}{m}$ in length and 7 ${\mu}{\textrm}{m}$ in width. Each of the glochidial shell valves has a 16 ${\mu}{\textrm}{m}$ long hook sitdded with many spines on the superior face. A large area to the apex of the valve surrounding the base of the hook is provided with numerous small spines which become progressively smaller towards the periphery of the area, The external surface of the glochidial shell valve is covered with numerous small processes showing successive change in the shape and the pattern of destribution by part. Besides the processes, there are a number of niches scattered all over the exterior surface. The glochidial shell valve has two layers. One is the outer thin membrane bearing the processes and the niches and the others is the inner layer bearing numerous holes which any accessory structure and 2.65 ${\mu}{\textrm}{m}$ in diameter, emerges from a canal located at center of ventral plate of the mamtle, A total of three types of the hair cells are observed. In present artificial infection of the glochidium to the guppy, it took about three to four hours to complete an early cysts, During the period of encystment, The epithelial cells of the host fish actively migrated toward the attached glochidium and covered it.

• Journal of Chest Surgery
• /
• v.54 no.5
• /
• pp.383-388
• /
• 2021

Background: Achieving external access to and manual occlusion of the left atrial appendage (LAA) during minimally invasive mitral valve surgery (MIMVS) through a small right thoracotomy is difficult. Occlusion of the LAA using an epicardial closure device seems quite useful compared to other surgical techniques. Methods: Fourteen patients with atrial fibrillation underwent MIMVS with concomitant surgical occlusion of the LAA using double-layered endocardial closure stitches (n=6, endocardial suture group) or the AtriClip Pro closure device (n=8, AtriClip group) at our institution. The primary safety endpoint was any device-related adverse event, and the primary efficacy endpoint was successful complete occlusion of blood flow into the LAA as assessed by transthoracic echocardiography at hospital discharge. The primary efficacy endpoint for stroke reduction was the occurrence of ischemic or hemorrhagic neurologic events. Results: All patients underwent LAA occlusion as scheduled. The cardiopulmonary bypass and aortic cross-clamp times in the endocardial suture group and the AtriClip group were 202±39 and 128±41 minutes, and 213±53 and 136±44 minutes, respectively (p=0.68, p=0.73). No patients in either group experienced any device-related serious adverse events, incomplete LAA occlusion, early postoperative stroke, or neurologic complication. Conclusion: Epicardial LAA occlusion using the AtriClip Pro during MIMVS in patients with mitral valve disease and atrial fibrillation is a simple, safe, and effective adjunctive procedure.

• Journal of Convergence for Information Technology
• /
• v.8 no.6
• /
• pp.389-397
• /
• 2018

Recently, Global Shale gas development has expanded, increasing shale gas production has transformed the energy market.As a result of the reduction of energy facilities, in order to overcome the management deterioration of domestic casting valve industry and enter the enlarged shale gas plant, tried to confirm the SWOT factor through the second questionnaire based on the questionnaire survey of related industry experts and previous studies. As a strength-strategy, presented three factors besides collaboration with domestic companies, suggested four factors including product development specialized in shale gas plant as a weakness complement. Thesis offer to scholarly-Practical implications, Internal-external environmental factors, strategization for entering New energy market. thesis offer to scholarly, Practical implications, environmental factors, strategization for entering New energy market. After, analyze a important of research strategy, would like to study the impact on the company according to the ranking of importance.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.3
• /
• pp.443-449
• /
• 2022

In this study, in order to improve the disadvantages of the environmental error of the infusion set that performs infusion therapy in the existing clinical practice and to maximize the user's convenience by miniaturizing the existing infusion pump system, the structure of the muscle pump of the human vein was imitated. As a double check valve method, a method for preventing the backflow of fluid and discharging a constant fluid in one direction by external pressure was proposed. The proposed bio-mimic muscle pump uses a check valve that controls the flow of fluid in one direction and a silicone tube with elasticity, and a chamber is constructed. A peristaltic pump for applying intermittent pressure to the tube chamber was constructed using a multi-cam structure roller. In order to verify the performance of the proposed pump, optimization was performed while changing the number of multi-cam rollers and adjusting the speed of the roller driving motor, and the reproducibility of the instantaneous discharge amount and the continuous discharge amount of the pump was compared and tested. The performance of the muscle pump proposed in this study was verified through experiments that it can inject up to 1L of fluid within 12 hours, and that it is possible to inject the fluid with an accuracy of ±0.1ml. Real-time monitoring of the fluid injection volume through the bio-mimic muscle pump proposed in this study not only increases the convenience of the administrator, but also provides a precise fluid administration environment to more patients at a low cost, and additionally applies bubble detection and occlusion detection technology If so, it is believed that a safer medical environment can be provided to patients.