• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2004년도 춘계 학술대회논문집
• /
• pp.49-55
• /
• 2004

This paper addresses a numerical simulation of the flow and heat transfer in a simplified model of helically coiled tube steam generator using a general purpose computational fluid dynamic analysis computer code. The steam generator model is comprised of a cylindrical shell and helically coiled tubes. A cold feed water entered the tubes is heated up, evaporates. and finally become a superheated steam with a large amount of heat transferred continuously from the hot compressed water at higher pressure flowing counter-currently through the shell side. For the calculation of tube side two-phase flow field formed by boiling, inhomogeneous two-fluid model is used. Both the internal and external turbulent flows are simulated using the standard k-e model. The conjugate heat transfer analysis method is employed to calculate the conduction in the tube wall with finite thickness and the convections in the internal and external fluids simultaneously so as to match the fluid-wall-fluid interface conditions properly. The numerical calculations are peformed for helically coiled tubes of steam generator at an integral type pressurized water reactor under normal operation. The effects of tube-side inlet flow velocity are discussed in details. The results of present numerical simulation are considered to be physically plausible based on the data and knowledge from previous experimental and numerical studies where available.

• 한국안전학회지
• /
• 제32권2호
• /
• pp.147-152
• /
• 2017

The external reactor vessel cooling (ERVC) is well known strategy to mitigate a severe accident at which nuclear fuel inside the reactor vessel is molten. In order to compare the heat removal capacity of ERVC between the nuclear reactor designs quantitatively, numerical method is often used. However, the study for ERVC using computational fluid dynamics (CFD) is still quite scarce. As a validation study on the numerical prediction for ERVC using CFD, the subcooled boiling flow and natural circulation of coolant at the ULPU-V experiment was simulated. The commercially available CFD software ANSYS-CFX was used. Shear stress transport (SST) model and RPI model were used for turbulence closure and wall-boiling, respectively. The averaged flow velocities in the downcomer and the baffle entry under the reactor vessel lower plenum are in good agreement with the available experimental data and recent computational results. Steam generated from the heated wall condenses rapidly and coolant flows maintains single-phase flow until coolant boils again by flashing process due to the decrease of saturation temperature induced by higher elevation. Hence, the flow rate of coolant natural circulation does not vary significantly with the change of heat flux applied at the reactor vessel, which is also consistent with the previous literatures.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.308-311
• /
• 2008

As a severe accident mitigation strategy in a nuclear power plant, ERVC(External Reactor Vessel Cooling) has been proposed. Under ERVC conditions, where a molten corium is relocated in a reactor vessel lower head, a natural circulation two-phase flow is driven in the annular gap between the reactor vessel wall and its insulation. This flow should be sufficient to remove the decay heat of the molten corium and maintain the integrity of the reactor vessel. Preliminary experimental study was performed to estimate the natural circulation two-phase flow. The experimental facility which is one dimensional, the half height, and the 1/238 channel area of APR1400, was prepared and the experiments were carried out to estimate the natural circulation two-phase flow with varying the parameters of the coolant inlet area, the heat rate, and the coolant inlet subcooling. In results, the periodic circulation flow was observed and the characteristics were varied from the experimental parameters. The frequency of the natural circulation flow rate increased as the wall heat flux increased.

• 한국화재소방학회:학술대회논문집
• /
• 한국화재소방학회 1997년도 International Symposium on Fire Science and Technology
• /
• pp.138-145
• /
• 1997

Models of upward flame spread have been attempted in the past, but in the current work an emphasis has been placed on developing a practical model that will be useful across a broad range of materials. Some of the important aspects of the model we: the addition of external radiation to simulate a wall that is a part of an enclosure fire and has flaming walls radiating to it, the use of a correlation for flame heat feedback distribution to the sample surface based on data available in the literature, and the use of an experimentally measured mass loss rate for the sample material, In this paper, the development of the numerical model is presented along with predictions of flame spread for three materials: hardboard, a relatively homogeneous wood-based material; plywood, which is made of laminated wood bonded by adhesives; and a composite material made of fiberglass matrix embedded in epoxy. Predictions are compared with measured data at several levels of external radiation for each material. For the materials tested, the model correctly predicts trends and does a reasonable job predicting flame heights. The need for thermal property data for practical materials, which would be appropriate for flame spread models, is indicated by this work.

• 한국구조물진단유지관리공학회 논문집
• /
• 제22권1호
• /
• pp.6-12
• /
• 2018

본 최근 건축물 외벽공사에 커튼월 공법의 사용이 증가하고 있다. 외벽 커튼월 공법은 공기단축 및 경제적 효용이 크다는 장점으로 인해 건물의 외벽으로도 널리 시공되고 있다. 그러나, 커튼월 공법의 프레임과 유리를 연결해 주는 구조용 실란트에 대한 내후성 및 구조물의 거동에 대한 열화를 대체한 시험은 KS F 4910 규격에는 부재한 실정으로 안정적인 커튼월 공법 도입과 품질향상을 위해서는 필요한 요소이다. 본 연구에서는 외기환경하에서 거동에 대한 탄성복원력시험을 실시하였다. 구조용 실란트를 대상으로 열에 대한 실링재의 열화를 평가하였다. 국내에서는 구조용 실란트의 가변형 변위거동에 대한 연구는 부족한 실정으로 본 연구에서는 외기 환경에 노출된 열화조건을 대체하여 실험실 조건에서 재현한 결과를 확인하고, 설계에 반영하고자 한다. 본 연구 결과에 따르면, 기존의 구조용 실링재는 KS F 4910의 품질기준은 만족하지만, 본 연구에서 실시한 조건에서는 시험체의 파단과 표면의 균열 등이 발생하는 것을 확인하였다. 특히, 내후성 시험에서는 시험체 모두 불용의 상태를 확인하여 향후, 커튼월 공법에 사용되는 구조용 실링재의 장기적인 내구성능 평가가 필요한 것으로 판단된다. 따라서, 기존의 구조용 실링재가 현장에 적용되기 위해서는 별도의 내구성능 평가를 실시가 요구된다.

• 한국태양에너지학회 논문집
• /
• 제24권2호
• /
• pp.25-31
• /
• 2004

Ventilation through air vent system in a building envelope is expected to be an effective measure to release solar radiation. An external surface of a wall absorbs solar radiation and transfers it to the air in the cavity. The warmed air gets buoyant force. So when openings are provided at the top and bottom of the cavity, the warmed air is released through the top opening and cooler outside air replaces the space in the cavity. This reduces the further heat transmission into the built environment. This natural ventilation effect seems to be steady and strong. So because of the cavity and the openings, the cooling load reduction by natural ventilation is believed to be considerable.

• 한국정밀공학회지
• /
• 제30권7호
• /
• pp.725-732
• /
• 2013

This paper presents a torque distribution algorithm for improving the stability and mobility of a wall-climbing robot platform. During ascent, the pitch moment caused by the payload or external disturbances separates the robot's triangular tracks from the wall, significantly deteriorating its stability. Moreover, the reaction forces stemming from the increase in the pulling force may degrade the robot's mobility. Thus, it is very important to minimize the reaction forces acting on the triangular tracks, as well as the fluctuations in the pulling force, during the climb. Through dynamic modeling of the proposed robot platform, we demonstrated the dependence of the robot's stability and mobility on the torque distribution of the triangular tracks. Extensive simulations using different climbing speeds were used to significantly improve the stability and mobility of the proposed robot platform.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.293-299
• /
• 2009

Many kinds of problems by stack effect occur in the high-rise buildings that have the simple plan on the first floor designed only by an external wall and an E/V shaft wall. Therefore, some buildings in the foreign countries has made the additional inside walls between lobby and E/V hall as a countermeasure on stack effect. An additional wall in the lobby is very useful countermeasure on stack problems because lobby is a main airflow path in the building. Decreasing effect on stack problems by an additional wall of lobby is reported in this study. An ordinary office building that has a simple lobby plan is simulated and measured in this study. The results show that characteristics on stack effect are changed by methods of applying additional walls and that alternations of countermeasures which building conditions like the kinds of problems and the problem's velocity etc. are considered are very important.

• Steel and Composite Structures
• /
• 제34권6호
• /
• pp.783-794
• /
• 2020

Steel-concrete-steel sandwich composite wall is composed of two external steel plates and infilled concrete core. Internal mechanical connectors are used to enhance the composite action between the two materials. In this paper, the compressive behavior of a novel sandwich composite wall was studied. The steel trusses were applied to connect the steel plates to the concrete core. Three short specimens with different truss spacings were tested under compressive loading. The boundary columns were not included. It was found that the failure of walls started from the buckling of steel plates and followed by the crushing of concrete. Global instability was not observed. It was also observed that the truss spacing has great influence on ultimate strength, buckling stress, ductility, strength index, lateral deflection, and strain distribution. Three modern codes were introduced to calculate the capacity of walls. The comparisons between test results and code predictions show that AISC 360 provides significant underestimations while Eurocode 4 and CECS 159 offer overestimated predictions.

• 펄프종이기술
• /
• 제39권1호
• /
• pp.1-7
• /
• 2007

Internal fibrillation of pulp fiber is an important factor affecting paper properties. Internal fibrillation of pulp fiber is usually introduced with several kinds of modifications of fiber by the mechanical treatment such as refining, high shear and/or high consistency mixing, etc. Unfortunately there are no standardized methods that can characterize the extent of internal fibrillation and its contribution on the paper properties. The purpose of this study is to try and find the potential methods that can characterize the internal fibrillation of pulp fiber quantitatively. Softwood bleached kraft pulp was treated with Hobart mixer to introduce the internal fibrillation without the significant fiber damage and external fibrillation. The extent of internal fibrillation was increased with the increase of mechanical treatment consistency. Several fiber properties were measured to find the potential means that could characterize and quantity the internal fibrillation. Laminated area could not be used as a means for quantifying the internal fibrillation because of the effect of swelling and the different internal fibrillation behavior at different mechanical treatment consistency. Micro and macro internal fibrillation models were proposed for describing the different behavior for the mechanical treatment at low and high consistencies of pulp. The Internal fibrillation showed good correlation with swelling of fiber wall. This trend was confirmed through the measurement of wall thickness and/or cross section area of fiber. Therefore the internal fibrillation possibly can be described as the indices indicating the change of wall thickness and/or cross section area.