• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.4
• /
• pp.368-378
• /
• 2004

In this paper, we proposed the compensation structures for the enhanced directivity of CPW(Coplanar waveguide) directional couplers with finite-extent backed conductor. The proposed compensation structures are. realized by expanding the slot width between signal line and ground plane in center region of couplers. The CPW couplers with expanded slot have the same phase velocity for even and odd mode because of added inductance and changed capacitance appropriately, so the enhanced directivity is accomplished. The designed CPW directional couplers have good directivity and matching characteristic at center frequency in simulation and measurement.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.14 no.5
• /
• pp.365-376
• /
• 2002

An experimental study has been conducted to measure the local film-cooling effectiveness and the heat transfer coefficient for a single row of rectangular-shaped holes. four different cooling hole shapes such ai a straight rectangular hole, a rectangular hole with laterally expanded exit, a circular hole and a two-dimensional slot are tested. A technique using thermochromic liquid crystals determine adiabatic film cooling effectiveness values and heat transfer coefficients on the test surface. Both film cooling effectiveness and heat transfer coefficient are measured for various blowing rates and compared with the results of the cylindrical ho1es and the two-dimensional slot. The flow patterns downstream of holes are calculated numerically using a cummercial package. The results show that the rectangular hopes provide better peformance than the cylindrical holes. For the rectangular holes with expanded exit, the penetration is reduced significantly, and the higher and more uniform cooling Peformance is obtained even at relatively high blowing rates.

• Journal of Satellite, Information and Communications
• /
• v.12 no.1
• /
• pp.132-136
• /
• 2017

In this paper, expanded lowest operating frequency by adopting circular slot on ground of balun and balance improved balance performances by stacking dielectric layer balun is proposed. Bandwidth of proposed balun is 1~7 GHz, and electrical length is $0.05{\lambda}$ at 1 GHz. In order to check performances of the proposed balun, simple dipole is integrated with the balun and radiation pattern of dipole is measured.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.2 no.3
• /
• pp.313-320
• /
• 2013

The fractional slot windings are widely used in rotating machine in order to increase the flexibility of design and improve the voltage waveform. However, the MMF wave of fractional-slot windings are found to contain unique harmonic component, which are designated as even order space flux harmonics, fractional number flux harmonics, or both. They may cause stray loss and stator core vibration. This paper proposes new winding methods "novel interspersed windings" and "expanded group windings" to reduce these harmonics. The advantages of two proposed windings are verified by using numerical analysis and measurement test of winding model.

• Journal of the Optical Society of Korea
• /
• v.11 no.4
• /
• pp.162-172
• /
• 2007

Scanning Laser Optical Tweezers(SLOT) is an optical instrument frequently employed on a microscope with laser being delivered through its various ports. In most SLOT systems, a mechanical tilt stage with a mirror on top is used to dynamically move the laser focal point in two-dimensions. The focal point acts as a tweezing spot, trapping nearby microscopic objects. By adding a mechanical translational stage with a lens, SLOT can be expanded to work in three-dimensions. When two mechanical stages operate together, the focal point can address a closed three-dimensional volume that we call a workspace. It would be advantageous to have a large workspace since it means one can trap and work on multiple objects without interruptions, such as translating the microscope stage. However, previous studies have paid less consideration of the volumetric size of the workspace. In this paper, we propose a new method for designing a SLOT such that its workspace is maximized through optimization. The proposed method utilizes a matrix based ray tracing method and genetic algorithm(GA). To demonstrate the performance of the proposed method, experimental results are shown.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.5
• /
• pp.428-434
• /
• 2009

In this paper, we propose an U-slot microstrip antenna with the U-shaped parasitic patches. U-slot and parasitic patches make two resonant frequencies and one additional resonant frequency, respectively, so that the impedance band-width of the antenna is expanded. The size of radiator part is $64{\times}53\;mm^2$ and the entire size of the antenna is $150{\times}150{\times}11.5\;mm^3$. The measured bandwidth is $1.85{\sim}2.40\;GHz$. Thus, our antenna can be used for DCS1900, WCDMA and WiMax services. The radiation characteristic is almost same in the bandwidth, the beam width is about $60^{\circ}$, and the gain is more than 7 dBi.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.5
• /
• pp.516-521
• /
• 2011

In this paper, an inverted-triangle patch UWB antenna with an uneven ground planes and an inverted T-slot for 5 GHz WLAN band rejection is presented. The operating bandwidth of the proposed antenna fed with the CPW line is expanded from 3.1 GHz to 10.6 GHz for about -10 dB return loss using three angular parameters correlated to the main patch and the ground plane. The fabricated antenna on Taconic RF-60A substrate with 6.16 relative dielectric constant and 0.64 mm thickness has a main antenna patch size of 36 mm${\times}$19.5 mm. The measured results show return losses of about -10 dB and nearly omni-directional radiation patterns. The proposed UWB antenna has advantages of easily adjustable impedance characteristics by the three angular parameters and easily accomplishable band rejection characteristics by the inverted T-slot.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.4A
• /
• pp.320-327
• /
• 2005

In this paper, compensation structures are proposed in the CPW directional couplers with finite-extent backed conductor for tight coupling. The proposed structures are realized T-shaped expanded slots and modified finite-extent backed conductor in CPW coupled structure. The T-shaped expanded slots was used to avoide reduced coupling and modified finite extent backed conductor of dumbbell shape was used to enhance directivity and matching. The designed CPW directional couplers at 1 GHz has good directivity without reducing coupling in simulation by EM solver based on full-wave analysis and measurements.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.9
• /
• pp.680-684
• /
• 1991

The scattering problem of a transverse electric (TE) plane wave by strip grating with a dielectric slab over a ground plane is analyzed by the method of moments. By use of equivalence principle, surface magnetic current density on the shorted slot is expanded in a series of Chebyshev polynomial a satisfying the appropriate edge condition. Numerical results for reflection coefficient are obtained and compared with other available results. Our numerical results obtained from the present method are in good agreement with other result available in the literature.

• The Transactions of the Korea Information Processing Society
• /
• v.5 no.10
• /
• pp.2654-2662
• /
• 1998

Maximum single bus throughput of standard IEEE 802.6 DQDB(Distributed Queue Dual Bus) is not obtained over 1. Therefore, lots of studies for improving bus throughput have done by QA slot preuse/reuse. We propose three calculation cethods for network's utilization with preuse/reuse scheme based on erasure nodes. One is calculation method by traffic density function, other is calculation method for obtaining maximum throughput. The other is calculation method using probability concept which follows real DQDB operation mechanisms. The calculated throughputs are compared with each others. The results shows some favorite phenomena. The proposed calculation methods can be casily expanded in mumber of nodes or in number of erasure nodes.