• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 1995년도 추계학술대회 학술발표 논문집
• /
• pp.125-130
• /
• 1995

Recently, the vehicle engine requried precision control of Air-Fuel rate and rigid restriction of exhaust gas. Therefore, we demanded excellent measuring equipment so as to improve of engine performance. Specially, throttle valve control is very important part in the engine control, because structure of engine dynamometer system is very important part in the engine control, because structure of engine dynamometer system is very complicate and it has nonlinear elements which is influenced of disturbance about vibration, a heat, a cooling, energy loss so on. In this study, we propose the method that the control technique using Fuzzy Look-up table and we obtained the satisfying result from realized the control system.

• Journal of Mechanical Science and Technology
• /
• 제19권12호
• /
• pp.2321-2329
• /
• 2005

One means of fulfilling $CO_2$ emission legislation is to downsize engines by boosting their power using turbochargers or mechanical superchargers. This reduces fuel consumption by decreasing the engine displacement. When a turbocharger, which is preferable to a mechanical supercharger in terms of fuel efficiency, is used, there is insufficient availability of exhaust gas energy at low engine speeds, resulting in an unfavorable engine response. Therefore, mechanically driven superchargers have increased in popularity due to their quick response to changing speeds in the transient phase. However, since a mechanical supercharger obtains its driving power from the engine, it is difficult to decrease its fuel consumption. This remains a large negative factor for superchargers, despite their excellent dynamic performance. This study aims to develop a power control concept to improve the fuel economy of a mechanical screw supercharger, which could then be used for engine downsizing.

• 한국산업융합학회 논문집
• /
• 제22권5호
• /
• pp.511-517
• /
• 2019

Two type pistons which had different configuration were made to find out the effects on combustion and flame propagation. Flame propagation speed was obtained by use of the cylinder head gasket ionization probe. Ionization Probe voltage output and flame propagation speed were increased according to the air fuel mixture ratio increase. Exhaust direction flame propagation speed was fastest in combustion chamber and next was front direction, rear direction and intake direction cause of tumbling motion in cylinder. In case of remove the valve pocket in piston, average flame propagation speed changed slowly and spark timing was advanced. Also emission was decreased.

• 소음진동
• /
• 제8권2호
• /
• pp.239-250
• /
• 1998

Traditionally, intake noise from internal combustion engine has not recevied much attention compared to exhaust noise. But nowadays, intake noise is a major contributing factor to automotive passenger compartment noise levels. The main objective of this paper is to identify the mechanism of generation, propagation and radiation of the intake noise. With a simplest geometric model, one of the main noise sources for the intake stroke is found to be the pressure surge, which is generated after intake valve closing. The pressure surge, which has the nonlinear acoustic behavior, propagates and radiates with relatively large amplitude. In this paper, unsteady compressible Navier-Stokes equations are employed for the intake stroke of axisymmetric model having a single moving cylinder and a single moving intake valve. To simulate the periodic motion of the piston and the valve, unsteady deforming mesh algorithm is employed and Thompson's non-reflecting boundary condition is applied to the radiation field. In order to resolve the small amplitude waves at the radiation field, essentially non-oscillatory(ENO) schemes with an artificial compression method (ACM) are used.

• 한국분무공학회지
• /
• 제9권2호
• /
• pp.9-17
• /
• 2004

The performance characteristics of lean burn system in gasoline engine are mainly affected by the air-fuel mixture in cylinder, gas exchange process of manifold system, exhaust emission of engine, and the electronic engine control system. In order to obtain the effect of performance factors on the optimum conditions of lean burn engine, this study deal with the behavior of mixture formation, gas flow characteristics of air, flow and evaporation analysis of spray droplet in cylinder, vaporization and burning characteristics of lean mixture in the engine, and the control performance of electronic engine control system. The optimum flow conditions were investigated with the swirl and tumble flows in the combustion chamber with swirl control valve. The performance characteristics and optimum condition of flow field in intake system were analyzed by the investigation of inlet flow of air and combustion stabilization on cylinder.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1992년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 19-21 Oct. 1992
• /
• pp.975-980
• /
• 1992

The purpose of this paper is to perform the engine driving well with controling the IAC(Idle Air Control) valve which controls the demand-air when the abrput increasing or decrasing and the idling, the fuel by controlling the injector, and the spark timing. This plant is the complex system because this should be controlled each other and each one affects other. We have controlled this system effectively by using Personal Computer in order to reduce the exhaust gas and improve the engine performance.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2014년도 추계학술대회 논문집
• /
• pp.172-173
• /
• 2014

QMS(quadruple mass spectrometer) system은 식각 및 증착 공정 중 chamber 내부의 잔류기체를 분석하여 다양한 실험환경과 조건에서 신뢰성 있는 혼합가스조성비를 분석할 수 있게 해주며 chamber 내부의 압력에 따라 hexblock의 valve를 통해 QMS의 내부 압력을 조절할 수 있다.

• 한국가스학회지
• /
• 제22권2호
• /
• pp.78-83
• /
• 2018

이 논문은 디젤엔진 자동차의 EGR 및 공기 제어와 CPF 장치에 관련된 고장사례 연구이다. 첫 번째 사례는 엔진진공펌프 손상으로 인해 엔진오일이 EGR 밸브 내부 다이어프램 손상으로 인해 오일이 흡기로 유입되어 연소실로 들어가 불완전 연소함으로써 배기할 때 매연이 발생된 것으로 확인되었다. 두 번째 사례의 원인은 공기제어 장치인 스로틀 플랩(throttle flap)을 점검하였을 때 스로틀 플랩이 고착되어 흡입공기량 부족에 의해 매연이 발생된 것을 확인하였다. 세 번째 사례는, 배기가스 온도센서의 불량으로 인해 온도를 감지하지 못해 재생기능이 되지 않아 매연이 발생된 것으로 확인되었다. 따라서, 배기가스발생으로 인한 환경오염 문제가 발생하지 않도록 최적의 상태를 유지하도록 관리하여야 한다.

• 동력기계공학회지
• /
• 제12권1호
• /
• pp.13-19
• /
• 2008

In this study, a variable induction and exhaust system is applied to turbocharged diesel engine to improve the volumetric efficiency, especially, in a low and transient engine speed range where much of the pollutant matters are expelled out. The volumetric efficiency is known as one of the most important factor which affects significantly engine performance, fuel economy and further emission and noise level. As the torque increase with the engine speed up, the gas flow in an exhaust pipe become pulsating and then has an effect on boost up capacity of air charging into the cylinder and expelling capacity to atmosphere simultaneously. But at a low and idling speed, the pulsation effect was not so significant. Accordingly, resonator was employed to compensate their loss. The variable induction system consists of the secondary pipe, resonator, intercooler, and torque variance were examined with extended operating conditions. In the mean time, for interpretation and well understanding for the phenomena of wave action that arising during intake and exhaust process between turbocharger and variable intake system, the concept of the combined supercharging was introduced. Some of results are depicted which deal with a pressure history during valve events of induction process. Consequently, by the governing of these phase and amplitude of pulsating wave, it enables us to estimate and evaluate for the intake system performance and also, designing stage of the system layout.

• Journal of Advanced Marine Engineering and Technology
• /
• 제41권1호
• /
• pp.21-30
• /
• 2017

현재 국내에서 공장 보수용접이 가장 많이 이루어지고 있는 선박 엔진 부품은 피스톤 크라운과 배기밸브이다. 또한 선박 엔진 밸브와 크랭크 축 등의 경우에는 신규 부품에서도 성능향상을 위해 표면개질방법으로 오버레이 용접이 시공되고 있다. 용착률을 높이는 고능률 오버레이 용접 공정으로 Hot Wire GTAW, Cold Tandem GMAW, Band Arc SAW, Tandem SAW법이 개발되어 있고, 용사방법으로 PTA공정이 현장에서 많이 시공되고 있다. 입열량 제어가 용이한 공정으로 GMAW-Pulse, CMT 용접공정이 있다. 엔진 배기밸브의 보수를 위한 오버레이공정에서 열영향부에 가까운 모재 내에 액화균열이 발생하는 경우가 있어 주의를 요한다. GMAW-Pulse 공정과 CMT공정에서는 입열량 제어가 용이하여 높은 용착속도를 유지하면서도 액화균열의 발생 없이 엔진 밸브의 보수 또는 표면 개질 목적으로 시공이 가능하다. 최근에 국내에서 고능률 용접 공정으로 선박엔진의 보수 또는 표면 개질 목적으로 사용 가능한 Super-TIG 용접공정이 개발되어 있다. 이 공정은 아크를 플라즈마 스트림이라고 보고 전류증가에 따라 커지는 아크압력을 막으면서도 용가재의 용융 효율이 극대화 되도록 폭이 큰 C형의 오목한 용가재를 발명하여 용착률을 획기적으로 향상시킨 용접공정이다.