• 오토저널
• /
• 제7권2호
• /
• pp.45-54
• /
• 1985

Recently, the problem of exhaust gas pollution is increasingly being aggravated by the active use of the Diesel engine. For the fuel-injection system which affects the composition of exhaust gas from the Bosch type single-hole nozzle in the Diesel engine, a mathematical model was set up to study pressure variations in the high pressure pipe, the injection rate, and the needle lift. The fundamental equations of the mathematical model have been solved by the Newton Raphson Method applying the Finite Diffrence Method. The effective stroke of the injection pump plunger due to a change in engine rpm was calculated by the measurement of Control Rack, Pinion, and Plunger sizes and by the use of Characteristic Curve of Governor. The computed results for the pressure variations in the high pressure pipe and needle lift at 800 rpm and 1000 rpm are in good agreement with experimental ones in general. By a developed program, the effects of other various parameters will by calculated for the performance of the fuel-injection system.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권3호
• /
• pp.394-403
• /
• 2008

The effects of water injection (WI) and urea injection for NOx on a 4-cylinder Direct Injection (DI) diesel engine were investigated experimentally. For water injection, it was installed at the intake pipe and the water quantity was controlled at the intake manifold and Manifold Air Flow (MAF) temperatures while the urea injection was located at the exhaust pipe and the urea quantity was controlled by NOx quantity and MAF. The effects of WI system, urea-SCR system and the combined system were investigated with and without exhaust gas recirculation (EGR). Several experiments were performed to characterize the urea-SCR system, using engine operating points of varying raw NOx emissions. The results of the Stoichiometric Urea Flow (SUF) and NOx map were obtained. In addition, NOx results were illustrated according to the engine speed and load. It is concluded that the NOx reduction effects of the combined system without the EGR were better than those with the EGR-based engine.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 학술대회 논문집 정보 및 제어부문
• /
• pp.334-336
• /
• 2005

According as quality of life improves, pursuit of agreeable iife became realistic problem. Specially, noise had been appraised to element that infiuence in human life directly and indirectly Therefore, necessity of study about noise control is increased for better labor conditions and agreeable habitat. In this paper, implementation of active mufflers using recursive LMS algorithms is presented. Analyze exhaust pipe noise of a gasoline and Diesel car and use adaptation IIR filter algorithm that stability is solidified and controled exhaust pipe noise of a car. computer simulation is performed to show the effectiveness of a proposed algorithm.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권6호
• /
• pp.645-653
• /
• 2005

The effects of a WI(Water Injection) at the intake Pipe and an urea injection at the exhaust pipe for a 4-cylinder DI(Direct Injection) diesel engine were investigated experimentally The water quantity was controlled by temperature of intake manifold and MAF(Manifold Air Flow). In addition, the urea quantify was controlled by NOx quantify and MAF. Effects of WI system, urea-SCR system and tandem system were investigated for with and without EGR(Exhaust Gas Recirculation). As the results. the SUF(Stoichiometric Urea Flow) and NOx map were obtained. In addition, NOx results can be visualized with engine speed and engine load. It was concluded. therefore, that the NOx reduction effects of the tandem system without the EGR were more than those with the EGR base engine.

• 한국안전학회지
• /
• 제9권2호
• /
• pp.3-11
• /
• 1994

This study discribes result of comparision of two other numerical method, method of characteristics (MOC) and Lax-Wendroff method(LWM) applied at wave action analysis of Intake and exhaust pipe. Partiality FCT(Flux Correct Transport) scheme is appeneded to LWM to protest unacceptable overshoots, occuring near discontinuity. The final conclusion of this study is that MOC should be replaced by a second order finite difference approach(such as the LW method). Clear benefits we can get by change are faster calculation, higher accuracy, conservation of mass and consistent calculation method.

• 동력기계공학회지
• /
• 제8권4호
• /
• pp.5-10
• /
• 2004

본 연구는 단기통 4행정 기관의 배기단의 형상에 따른 실험과 수치해석이 소개되었다. 흡 배기 밸브가 작동하고 있고, 주요한 배기단의 변수로는 배기단 직경이 적용이 되었다. 실험결과로는 배기단의 직경에 따라 배기 압력은 많은 영향을 받았는 것으로 나타났다. 배기단의 직경이 감소하였을때, 배기압력파의 진폭과 파수가 증가되었다. 배기단의 직경이 증가 하였을 때, 배기압력파의 진폭이 감소하였다. 직경이 22mm 일 때의 소음의 주파수 분석이 16mm와 28mm 보다 진폭이 작게 나타났다.

• International Journal of Fluid Machinery and Systems
• /
• 제6권4호
• /
• pp.213-221
• /
• 2013

The characteristics of the thrust for ship propulsion equipment directly driven by air compressed by pressure fluctuation in a blower piping system are investigated. The exhaust valve is positioned upon the air ejection hole in the discharge pipe in order to induce the large-scale pressure fluctuation, and the effects of the valve on the pressure in the pipes and the thrust for the propulsive nozzle are examined. The pressure in the pipes decreases immediately after the valve is opened, and it increases just before the valve is closed. The thrust for the propulsive nozzle monotonically increases with increasing number of revolutions and depth. The interfacial wave in the nozzle appears in the frequency of approximately 4Hz, and it is important for the increase of the thrust to synchronize the opening-closing cycle for the exhaust valve with the generation frequency of the interfacial wave. The finite difference lattice Boltzmann method is helpful to investigate the characteristics of the flow in the nozzle.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2004년도 제29회 KOSCI SYMPOSIUM 논문집
• /
• pp.206-212
• /
• 2004

It is necessary to consider the stability, economic environmental-friendly problems by the development of the road, supply of the automobile, environmental problem as designing the exhaust system. To reduce the noise and the vibration of the automobile, it is needed to consider the pulsation noise, air current noise, vibration of air pipe which generate the intake and exhaust noise of the automobile. Moreover, the discharge sounds, intake sound, radiation sound, transmitted sound are occurred. To reduce this influence, the variable valve is needed and to control these factors, path transformation muffler and active type muffler are needed. While engine efficiency could be reduced with this transformationand resistance by the pressure, thermal property. In this study, how to design exhaust systems yielding higher condversion efficiency, lower backpressure and optimize the performance. this study is recommended for exhaust system and designers and engineers involved in SI engine exhaust system and it will furnish information for you to design more efficient.

• 한국자동차공학회논문집
• /
• 제10권1호
• /
• pp.24-31
• /
• 2002

An experimental study was conducted to investigate the effects of EGR (Exhaust Gas Recirculation) variables on performance and emission characteristics in a 2-liter 4-cylinder spark-ignition LPG fuelled engine. The effects of EGR on the reduction of thermal loading at exhaust manifold were also investigated because the reduced gas temperature is desirable for the reliability of an engine in light of both thermal efficiency and material issue of exhaust manifold. The steady-state tests show that the brake thermal efficiency increased and the brake specific fuel consumption decreased with the increase of EGR rate in hot EGR and with the decrease of EGR temperature in case of cooled EGR, while the stable combustion was maintained. The increase of EGR rate or the decrease of EGR temperature results in the reduction of NOx emission even in the increase of HC emission. Furthermore, decreasing EGR temperature by $180^{\circ}C$ enabled the reduction of exhaust gas temperature by $15^{\circ}C$ in cooled EGR test at 1600rpm/370kPa BMEP operation, and consequently the reduction of thermal load at exhaust. The optimization strategy of EGR application is to be discussed by the investigation on the effect of geometrical characteristics of EGR-supplying pipe line.

• 한국자동차공학회논문집
• /
• 제2권3호
• /
• pp.21-32
• /
• 1994

The Problem of mechanical vibration is investigated for an automotive exhaust system. The vibrational reduction effect is systematically evaluated according to the attachment of the exhaust system. Moreover, the optimal attachment position of bellows is determined from the viewpoint of vibration isolation. The structure is analysed by the finite element technique where the geometry, the mass, the stiffness and the damping properties of the exhaust pipe are modeled. The validity of the developed model is verified by comparing with the experimental results. An optimization is carried out by the quadratic approximation algorithm. The reaction transferred to an automobile body by the hanger is considered ad the objective function. It is shown that the exhaust system which has the bellows at the optimal position is more effective for the vibrational characteristics than the others. It is also proved that this analytical method is quite useful in the design stage of the exhaust system.