• 대한기계학회논문집B
• /
• 제26권2호
• /
• pp.211-218
• /
• 2002

It has been investigated for the temperature profile in a planar evaporator of micro-cooler subject to a uniform heat flux prior to tole initiation of boiling. The results of the analysis allow for the determination of applied power levels fur which nucleation is likely to occur only within the vapor grooves of the evaporator while maintaining subcooling in the liquid core, thereby increasing the likelihood of a successful startup. Also, limits are fecund for which additional increases in the applied heat flux do not increase the temperature difference between the vapor grooves and the wick-liquid core interface. This analysis is appropriate for the microscale evaporators of micro-cooler during a fully-flooded startup as well as starter pump designs and micro-CPLs(capillary pumped loops). The results are useful in the initial basic design of microscale heat transfer devices.

• 한국자동차공학회논문집
• /
• 제15권2호
• /
• pp.95-100
• /
• 2007

An experimental study was performed to evaluate the in-plate evaporation heat transfer and flow characteristics of a evaporator used in automobile. Two test-cores with different heat transfer area, bead-shape and bead-array were tested, A type and B type. For the heat transfer, Nusselt number for B type test-core reaches a value nearly equal to the one for A type test-core, in the whole range of equivalent Reynolds number. But, for the same mass flow rate of refrigerant, hA for B type test-core becomes higher with the increase of the mass quality of refrigerant than for A type test-core. In a flow visualization experiment, the wake zone of refrigerant circulating at u-turn position of plate is observed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.252-259
• /
• 2001

It is derived for the temperature profile in a cylindrical and planar shape capillary pumped loop evaporators subject to a uniform heat flux prior to the initiation of boiling using the finite difference method. The results of the analysis allow for the determination of applied power levels for which nucleation is likely to occur only within the vapor grooves of the evaporator while maintaining subcooling in the liquid core, thereby increasing the likelihood of a successful startup. Also, limits are found for which additional increases in the applied heat flux do not increase the temperature difference between the vapor grooves and the wick-liquid core interface. Several advantages of larger diameter evaporators observed experimentally in startup are explained and quantified by the model. This analysis is appropriate for standard capillary pumped loop evaporators during a fully-flooded startup as well as starter pump designs and loop heat pipes.

• 한국자동차공학회논문집
• /
• 제21권6호
• /
• pp.175-182
• /
• 2013

Lately, customers think highly of the emotional satisfaction and as a result, issues on odor are matters of concern. The cases are odor of interior material and air-conditioner of vehicles. In particualar, with respect to the odor of air-conditioner, customers strongly claimed defects with provocative comments : "It smells like something rotten," "It smells like a foot odor," "It stinks like a rag." Generally, it is known that mold of evaporator core in the air-conditioning system decays and this produce VOCs which causes the odor to occur. In this study, partial least squares regression model is applied to predict the strength of the odor and select of important VOCs which affect car air conditioning smell. The PLS method is basically a particular multilinear regression algorithm which can handle correlated inputs and limited data. The number of latent variable is determined by the point which is stabilized mean absolute deviations of VOCs data. Also multiple linear regression is carried out to confirm the validity of PLS method.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.126-126
• /
• 2011

수직으로 정렬된 1차원 ZnO nanorod arrays (NRAs)는 효율적인 반사방지 특성의 기하학적 구조를 갖고 있어, 크기와 모양 그리고 정렬형태의 다양한 설계를 통해 빛의 흡수율과 광 추출효율을 증가시켜 광전소자 및 태양광 소자의 성능을 향상시킬 수 있으며, 최근 이러한 연구에 대한 관심이 집중되고 있다. 본 연구에서는 ZnO NRAs의 넓은 표면적과 불연속적인 독특한 표면을 활용하여 광학적 특성을 효과적으로 개선하였다. 실험을 위해, thermal evaporator를 사용하여 Au와 Ag 그리고 e-beam evaporator를 사용하여 $SiO_2$를 ZnO NRAs 표면에 여러 가지 조건으로 증착하여, 독특한 계층 나노구조의 형성과 광학적 특성을 관찰하였다. 표면 roughness가 큰 FTO/glass 위에 수열합성법을 통해 끝이 뾰족하고, 비스듬히 정렬된 ZnO nano-tip array에 Au를 증착할 경우 ZnO/Au core/shell 구조가 형성되며, Au의 광 흡수율이 매우 크게 증가함을 관찰할 수 있었다. 반면 flat한 표면위에 빽빽하게 수직으로 정렬된 ZnO NRAs를 성장시켜 그 위에 Ag를 증착할 경우, evaporated Ag flux가 ZnO nanorod의 사이에 scattered 되어 ZnO nanorod 기둥의 측면에 직경이 50 nm 이하인 nanoparticles이 decorated 되어 국소표면플라즈몬 현상이 관찰되었으며, 이러한 효과를 통해 입사되는 빛의 흡수율을 효과적으로 증가시킬 수 있었다. 또한, ZnO NRAs의 표면에 $SiO_2$를 e-beam evaporator를 이용하여 증착할 경우, 자연적으로 vapor flux와 ZnO nanorod 사이에 oblique angle이 $80^{\circ}$ 이상으로 증가하여 $SiO_2$ nanorods가 자발적으로 형성되어 ZnO/$SiO_2$ branch 계층형태의 나노구조를 제작할 수 있었다. 이러한 구조는 유효 graded refractive index profile로 인해 기존의 ZnO NRAs보다 개선된 반사방지 특성을 나타냈다. 이러한 계층 나노구조의 광학적 특성을 시뮬레이션을 통해 이론적으로 분석을 통해 광전자 소자의 성능의 개선에 대한 적용 가능성을 조사하였다.

• 한국자동차공학회논문집
• /
• 제16권1호
• /
• pp.37-44
• /
• 2008

The global warming potential (GWP) of $CO_2$ refrigerant is 1/1300 times lower than that of R134a. Furthermore, the size and weight of the automotive heat pump system can decrease because $CO_2$ operates at high pressure with significantly higher discharge temperature and larger temperature change. The presented $CO_2$ heat pump system was designed for both cooling and heating in fuel cell vehicles. In this study, the performance characteristics of the heat pump system were analyzed for heating, and results for performance were provided for operating conditions when using recovered heat from the stack coolant. The performance of the heat pump system with heater core was compared with that of the conventional heating system with heater core and that of the heat pump system without heater core, and thus the heat pump system with heater core showed the best performance among the selected heating systems. On the other hand, the heating performance of two different types of coolant/air heat pump systems with heater core was compared each other at various coolant inlet temperatures. Furthermore, to use exhausted thermal energy through the radiator, experiments were carried out by changing the arrangement of a radiator and an outdoor evaporator, and quantified the heating effectiveness.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.2380-2382
• /
• 2005

UV-LIGA 공정을 이용하여 3차원 마이크로 인덕터 제작 기술에 관하여 연구하였다. 마이크로 인덕터의 코일, 비아(via), 코어(core)의 Multi-layer 제작을 위해 UV-LIGA 공정을 이용하였으며, 전해도금(electro plating)을 위한 씨올기(seed layer)로서는 e-beam evaporator를 이용하여 금속을 증착하였다. 3차원 마이크로 인덕터의 도금 방법으로는 전해도금을 사용하였으며, 코일과 비아 부분은 구리(Cu) 전해도금, 코어 부분은 니켈(Ni)과 철(Fe)의 합금인 퍼멀로이(Ni/Fe) 전해도금을 하였다. 3차원 마이크로 인덕터의 샘플크기로는 코어의 폭은 $300{\mu}m$, 전체 길이는 9.2mm, 두께는 $20{\mu}m$의 구조로 제작되었으며, 코일 부분은 폭이 $40{\mu}m$, 두께는 $30{\mu}m$이며, 코일턴 수는 70회의 구조로 제작하였다.

• 대한기계학회논문집B
• /
• 제20권2호
• /
• pp.720-729
• /
• 1996

An analysis of convective boiling heat transfer for refrigerant mixtures is performed for an annular flow to investigate the degradation of the heat transfer rate. Annular flow is selected in this study because a great portion of the evaporator in the refrigeration and air conditioning system is known to be in the annular flow regime. Mass transfer effect due to composition difference between liquid and vapor is included in this analysis, which is considered to be one of driving forces for the mass transfer at the interface. Due to the concentration gradient at the interface the mass transfer is interfered, so is the evaporative heat transfer at the interface. The mass transfer resistance makes the interface temperature slightly higher and, as a result, the heat transfer coefficients decrease compared with those without mass transfer effects. The degradatioin of the heat transfer rate reaches its maximum at a certain composition. The composition difference between vapor core and vapor at the interface has a direct effect on the temperature difference between the vapor core and the interface and the degradation of the heat transfer rate. Correction factor $C_{F}$ for the mixture effects is added to the correlation for pure substances and the flow boiling heat transfer coefficients can be calculated using the modified equation.n.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.365-370
• /
• 2001

There are various wick types for heat pipe. In the present study, the manufacturing technology of a sintered wick among various wick types is discussed. The sintering technology using metal has been applied broadly in the field of electronic-telecommunication as well as heat pipes. A study of manufacturing procedure and characteristic of sintered wick for heat pipe have been performed. Copper powder was used as wick material and stainless steel as a mandrel. A manufacturing technology of the mandrel for arranging vapor core in heat pipe, a sintering technology by first or second times and operating temperature for sintering, the measurements of a porosity, pore size, and pore distribution of sintered wick were considered. In the meantime, a heat pipe with sintered wick has been manufactured and a performance test of the heat pipe has been performed in order to review cooling performance. The performance test results for the 4mm diameter heat pipe with the sintered wick shows the stability since the temperature difference between a evaporator and a condenser of the heat pipe is less than $4.4^{\circ}C$, and thermal resistance is less than $0.7^{\circ}C/W$.

• Macromolecular Research
• /
• 제10권4호
• /
• pp.204-208
• /
• 2002

A linear rod-like molecule, bis[4-(1,3-octadynyl)phenyl] terephthalate (2), consisting of two diacetylenic groups, was prepared. The unsymmetric diacetylene was prepared by the Cadiot-Chodkiewicz coupling reaction of 1-bromohexyne with 4-ethynylphenol and linked to a benzene core by an esterification reaction with terephthaloyl chloride in tetrahydrofuran. The thin film (200 nm thickness) of compound 2 was fabricated by the physical vapor deposition on a glass plate with a thermal evaporator. In the X-ray diffraction (XRD) study, the vapor deposited film on the glass plate showed peaks with d spacings of 19.4, 5.7, and 4.5 $\AA$. This XRD pattern was quite different from that observed for compound 2 isolated by recrystallization from methylene chloride/hexane. The vapor deposited film was polymerized by UV irradiation. Photopolymerization was carried out through a photomask, resulting in a patterned image, where the irradiated part became isotropic.