• Journal of Pharmaceutical Investigation
• /
• v.26 no.2
• /
• pp.71-82
• /
• 1996

This study has been undertaken to evaluate hydrophobic cyclodextrin(CD) derivatives as a sustained release carrier of azidothymidine(AZT), AZT, which has potent activity against AIDS and AIDS-related complex as thymidine analogue, has been reported that it has significant toxicity and short half life. Therefore, it is necessary to design sustained release oral dosage form to avoid undesirable side effects attributable to an excessive plasma concentration and to reduce the frequency of administration of AZT. Inclusion complexes of AZT with $acetyl-{\beta}-cyclodextrin\;(AC{\beta}CD)$ and $triacetyl-{\beta}-cyclodextrin(TA{\beta}CD)$ were prepared by solvent evaporation method. Interactions of AZT with CD were investigated by Differential Scanning Calorimetry(DSC) and Infrared Spectrophotometry(IR). The decreasing order of water solubilities of AZT and AZT-CD inclusion complexes were as follows; $AZT\;(27.873{\pm}0.015,mg/ml)\;>\;AZT-AC{\beta}CD\;(3.377{\pm}0.003)\;>\;AZT-TA{\beta}CD\;(2.528{\pm}0.001)$. Partition coefficients of $AZT-AC{\beta}CD\;and;\AZT-TA{\beta}CD$ inclusion complexes were increased by 1.27-fold, 1.54-fold in pH 1.2 and 1.32-fold, 1.47-fold in pH 6.8 in comparison with that of AZT. The mean dissolution time (MDT, min) which represents the rapidity of dissolution rate of AZT, $AZT-AC{\beta}CD,\;AZT-TA{\beta}CD$ were 5.12, 14.02 and 19.38 min in pH 1.2 and 2.52, 15.19 and 18.19 min in pH 6.8. AZT was very rapidly and completely dissolved in pH 1.2 and pH 6.8 within 5 minutes. But AZT-CD inclusion complexes showed the sustained release pattern in comparison with AZT alone. The simultaneous in situ nasal and jejunal recirculation study to compare the intrinsic absorptivity and the property of absorption sites revealed that the absorption of $AZT-TA{\beta}CD\;(N:35.35{\pm}1.08%,\;J:27.47{\pm}1.18%)$ was more than that of $AZT\;(N:16.89{\pm}2.25%,\;J:15.86{\pm}2.33%)$. The above results suggest that $TA{\beta}CD$ which is a hydrophobic cyclodextrin may serve as sustained release carrier with absorption enhancing effect.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.62 no.2
• /
• pp.63-73
• /
• 2020

Drought is considered as a devastating hazard that causes serious agricultural, ecological and socio-economic impacts worldwide. Fundamentally, the drought can be defined as temporarily different levels of inadequate precipitation, soil moisture, and water supply relative to the long-term average conditions. From no unified definition of droughts, droughts have been divided into different severity level, i.e., moderate drought, severe drought, extreme drought and exceptional drought. The drought severity classification defined the ranges for each indicator for each dryness level. Because the ranges of the various indicators often don't coincide, the final drought category tends to be based on what the majority of the indicators show and on local observations. Evaporative Stress Index (ESI), a satellite-based drought index using the ratio of potential and actual evaporation, is being used as a index of the droughts occurring rapidly in a short period of time from studies showing a more sensitive and fast response to drought compared to Standardized Precipitation Index (SPI), and Palmer Drought Severity Index (PDSI). However, ESI is difficult to provide an objective drought assessment because it does not have clear drought severity classification criteria. In this study, U.S. Drought Monitor (USDM), the standard for drought determination used in the United States, was applied to ESI, and the Percentile method was used to classify drought categories by severity. Regarding the actual 2017 drought event in South Korea, we compare the spatial distribution of drought area and understand the USDM-based ESI by comparing the results of Standardized Groundwater level Index (SGI) and drought impact information. These results demonstrated that the USDM-based ESI could be an effective tool to provide objective drought conditions to inform management decisions for drought policy.

• Analytical Science and Technology
• /
• v.27 no.4
• /
• pp.187-195
• /
• 2014

It is very important to minimize the damage of latent fingerprints at enhancing the contrast. This study proves the enhancement effects of cyanoacrylate-fumed latent fingerprints using p-dimethylaminobenzealdehyde (DMAB) on semi-porous surfaces and the influence factors. The latent fingerprints in experiment were developed for cyanoacrylate treatment in a vacuum chamber and used after drying at room temperature for 24 hours. For fluorescence staining, the cyanoacrylate-developed marks using DMAB were sublimated during 48 hours under the different conditions of surface area, temperature, atmospheric pressure. First experiment showed how surface area effects on the sublimation rate and fluorescence intensity by DMAB of particle size and container size. In addition, the fluorescence staining using DMAB with solvent-free contact method had the greatest fluorescence intensity after 36 hours and a low fluorescence intensity over a certain size of surface area. Second experiment showed that the evaporation of DMAB solid crystals got a satisfying result in a temperature of $20^{\circ}C$ and reduced time to get the greatest fluorescence intensity. It took a long time to get a optimum level of fluorescence intensity at $30^{\circ}C$ or more and it was less effective in fluorescence intensity. Third experiment on the pressure indicated that the fluorescence intensity of vacuum was weaker than nonvacuum but it was inapplicable to very high variations in pressure.

• The Korean Journal of Physiology and Pharmacology
• /
• v.19 no.6
• /
• pp.543-547
• /
• 2015

We investigated the combined moisturizing effect of liposomal serine and a cosmeceutical base selected in this study. Serine is a major amino acid consisting of natural moisturizing factors and keratin, and the hydroxyl group of serine can actively interact with water molecules. Therefore, we hypothesized that serine efficiently delivered to the stratum corneum (SC) of the skin would enhance the moisturizing capability of the skin. We prepared four different cosmeceutical bases (hydrogel, oil-in-water (O/W) essence, O/W cream, and water-in-oil (W/O) cream); their moisturizing abilities were then assessed using a $Corneometer^{(R)}$. The hydrogel was selected as the optimum base for skin moisturization based on the area under the moisture content change-time curves (AUMCC) values used as a parameter for the water hold capacity of the skin. Liposomal serine prepared by a reverse-phase evaporation method was then incorporated in the hydrogel. The liposomal serine-incorporated hydrogel (serine level=1%) showed an approximately 1.62~1.77 times greater moisturizing effect on the skin than those of hydrogel, hydrogel with serine (1%), and hydrogel with blank liposome. However, the AUMCC values were not dependent on the level of serine in liposomal serine-loaded hydrogels. Together, the delivery of serine to the SC of the skin is a promising strategy for moisturizing the skin. This study is expected to be an important step in developing highly effective moisturizing cosmeceutical products.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.612-619
• /
• 2002

The dynamic behavior of Al-Mg alloys plasma was very unstable and this instability was closely related to the unstable motion of keyhole during laser irradiation. The keyhole fluctuated both in size and shape and its fluctuation period was about 440 ${\mu}{\textrm}{m}$. This instability has been estimated to be caused by the evaporation phenomena of metals with different boiling point and latent heats of vaporization. Therefore, the authors have conducted the spectroscopic diagnostics of plasma induced in the pulsed YAG laser welding of Al-Mg alloys in air and argon atmospheres. In the air environment, the identified spectra were atomic lines of Al, Mg, Cr, Mn, Cu, Fe and Zn, and singly ionized Mg line, as well as strong molecular spectrum of AlO, MgO and AIH. It was confirmed that the resonant lines of Al and Mg were strongly self-absorbed, in particular in the vicinity of pool surface. The self-absorption of atomic Mg line was more eminent in alloys containing higher Mg. These facts showed that the laser-induced plasma was relatively a low temperature and high density metallic vapor. The intensities of molecular spectra of AlO and MgO were different each other depending on the power density of laser beam. Under the low power density irradiation condition, the MgO band spectra were predominant in intensity, while the AlO spectra became much stronger in higher power density. In argon atmosphere the band spectra of MgO and AlO completely vanished, but AlH molecular spectra was detected clearly. The hydrogen source was presumably the hydrogen solved in the base Metal, absorbed water on the surface oxide layer or H$_2$ and $H_2O$ in the shielding gas. The temporal change in spectral line intensities was quite similar to the fluctuation of keyhole. The time average plasma temperature at 1 mm high above the surface of A5083 alloy was determined by the Boltzmann plot method of atomic Cr lines of different excitation energy. The obtained electron temperature was 3, 280$\pm$150 K which was about 500 K higher than the boiling point of pure aluminum. The electron number density was determined by measuring the relative intensities of the spectra1lines of atomic and singly ionized Magnesium, and the obtained value was 1.85 x 1019 1/㎥.

• Food Science of Animal Resources
• /
• v.24 no.1
• /
• pp.97-102
• /
• 2004

The objective of this study was to control Kimchi fermentation using pH sensitive bacteriocin entrapping liposome(bacteriocin-liposome). The liposomes were prepared by the reverse-phase evaporation method from a mixture of DPPC(dipalmitoyl phosphatidylcholine, DPPE(dipalmitoyl phosphatidylethanolamine), DOPC(dioleoyl phosphatidylcholine) and cholesterol in a molar ration of 4:2:1:4. The bacteriocin-liposome was disruptured at pH 4 of buffer and was stable at alkaline pHs(6 and 7). Irrespective of the addition of the bacteriocin-liposomes, the pH of every Kimchi sample decreased to 5 during 5 days storage at 5$^{\circ}C$. Kimchi samples treated with bacteriocin-liposomes maintained pH 4 or higher, while Kimchi samples not treated with bacteriocin-liposomes exhibited pH 3.58 or lower. In general, the pH of Kimchi samples stored at 20$^{\circ}C$ decreased faster, compared to that of Kimchi samples stored at 5$^{\circ}C$. The pH of Kimchi samples treated with the bacteriocin-liposomes was 3.9 during 90 days storage, while that of the samples not treated with the bacteriocin-liposomes was 3.68 and 3.32 during 30 days and 90 days storages, respectively. Lactic acid bacteria in Kimchi treated with the bacteriocin-liposome grew relatively slow at 5$^{\circ}C$. The viable cell number of lactic acid bacteria increased up to 4${\times}$10$\^$7/ cells/ml and then decreased to 8${\times}$10$\^$6/ cells/ml during 90 days storage at 5$^{\circ}C$.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.46 no.3
• /
• pp.307-317
• /
• 2020

The barrier structure of the skin's epidermis is a key structure to prevent the loss of water inside the body and the invasion of foreign substances, and is composed of keratinocytes and intercellular lipids. At this time, the intercellular lipids of the skin barrier has the strongest structure when packed in an orthorhombic structure. However, it is damaged by various external causes and changes to a hexagonal structure. This change in physical structure can be analyzed non-invasively by analyzing the signal of the CH₂-CH₂ scissoring band of lipids using FT-IR. In this study, SDS was treated on porcine skin to construct a skin barrier damage model, and the degree of change in packing structure was quantified by analyzing FT-IR signals. We then judged whether the barrier of the damage model was recovered according to the treatment of the cosmetic formulation. From these results, an indirect method of measuring the water evaporation of the skin barrier to date can be supplemented. In addition, physical changes in the structure of the skin barrier can be utilized in a direct and efficient manner to identify the function and verify the formulation of various materials.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.417-423
• /
• 2007

Oxy-gasification or oxygen-blown gasification, enables a clean and efficient use of coal and opens a promising way to CO2 capture. The coal gasification process of a slurry feed type, entrained-flow coal gasifier was numerically predicted in this paper. The purposes of this study are to develop an evaluation technique for design and performance optimization of coal gasifiers using a numerical simulation technique, and to confirm the validity of the model. By dividing the complicated coal gasification process into several simplified stages such as slurry evaporation, coal devolatilization, mixture fraction model and two-phase reactions coupled with turbulent flow and two-phase heat transfer, a comprehensive numerical model was constructed to simulate the coal gasification process. The influence of turbulence on the gas properties was taken into account by the PDF (Probability Density Function) model. A numerical simulation with the coal gasification model is performed on the Conoco-Philips type gasifier for IGCC plant. Gas temperature distribution and product gas composition are also presented. Numerical computations were performed to assess the effect of variation in oxygen to coal ratio and steam to coal ratio on reactive flow field. The concentration of major products, CO and H2 were calculated with varying oxygen to coal ratio (0.2-1.5) and steam to coal ratio(0.3-0.7). To verify the validity of predictions, predicted values of CO and H2 concentrations at the exit of the gasifier were compared with previous work of the same geometry and operating points. Predictions showed that the CO and H2 concentration increased gradually to its maximum value with increasing oxygen-coal and hydrogen-coal ratio and decreased. When the oxygen-coal ratio was between 0.8 and 1.2, and the steam-coal ratio was between 0.4 and 0.5, high values of CO and H2 were obtained. This study also deals with the comparison of CFD (Computational Flow Dynamics) and STATNJAN results which consider the objective gasifier as chemical equilibrium to know the effect of flow on objective gasifier compared to equilibrium. This study makes objective gasifier divided into a few ranges to study the evolution of the gasification locally. By this method, we can find that there are characteristics in the each scope divided.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.6
• /
• pp.308-316
• /
• 2019

Electron beam physical vapor deposition (EBPVD) is a conventional method to fabricate thermal barrier coating (TBC) of high temperature airfoil engine parts, such as blade etc. for its high temperature structural stability from the nature of columnar growth behavior. For the high quality of TBC by EBPVD, the structural factors, such as growth behavior, thickness uniformity and so on, should be managed to obtain the coating which satisfied the required specifications of usable level of mechanical and thermal properties. In this study, the growth behavior and structure variations of 7YSZ (7 wt% yttria stabilized zirconia) coatings with different configurational deposition parameters for the specimens which have turbine blade shape mock-up were investigated. Growth behavior of coatings were studied by comparing computational modeling of evaporation behavior with actual deposition process using e-beam source.

• Journal of the Korean earth science society
• /
• v.28 no.6
• /
• pp.699-706
• /
• 2007

The purpose of this study is to examine the perceptions of pre-service teachers, which directly affect the concepts and ways of thinking of students who are studying Earth science. This work further seeks to identify pre-service Earth science teachers' Earth science-centered ways of thinking regarding the components and the process of water cycle. The concept sketch method was used to survey 50 pre-service teachers who majored in Earth science education at a National Teachers' University. The survey analyzed the preservice teachers' perceptions of a subordinate concept of Earth systems from the applied components of water cycle, and to code the applied concepts with the components of the water cycle based on a subordinate concept of Earth systems including Hydrosphere, Atmosphere, Geosphere, and Biosphere. The preservice teachers only perceived the components of the water cycle as ones in Hydrosphere and Atmosphere. In Biosphere, many participants lack the knowledge about how the actions of plants and animals, and human beings impact the water cycle. About the process of water cycle, the majority of the participants only perceived evaporation and precipitation as the process of cycling: their understanding about the underground flow of water was more lacking than the surface flow.