• 설비공학논문집
• /
• 제12권6호
• /
• pp.550-560
• /
• 2000

In order to minimize compression power and analyze the cause of exergy loss for a dry ice production cycle with 3-stage compression, the variation of compression power was investigated and the exergy analysis was peformed for the cycle. In this cycle, $CO_2$, is used both as a refrigerant and as a raw material for dry ice. The behavior of compression power and irreversibility in the cycle were examined as a function of intermediate pressure. From this result, the conditions for the minimum compression power were obtained in terms of the first stage or the third stage pressure. In addition, the irreversibilities for the cycle were investigated with respect to the efficiency of compressor. Result shows that the optimum pressure is not consistent with the conventional pressure obtained from the equal-pressure-ratio assumption. This is mainly due to the change in mass flow rate of the intermediate stage compressor by the flash gas evaporation from the flash drums. Most important is that the present exergy analysis enabled us to find bad performance components for the cycle and informed us of methods to improve the cycle performance.

• 약학회지
• /
• 제44권4호
• /
• pp.293-299
• /
• 2000

Biodegradable microspheres made from poly-lactide-co-glycolide polymers have been considered as a new delivery system for single-dose vaccine. Purified tetanus toxoid (TT) was encapsulated in poly-lactide(PLA) and poly-lactide-co-glycolide (PLGA) microparticles using a solvent evaporation method in a multiple emulsion system (water-in oil-in water). The morphology of 77-loaded microparticles was spherical and the suface of them was smooth. The particle size was in a range of 2-10. Protein loading efficiency was 68-97.8%. PLGA (85:15) microparticle showed the highest efficiency. Protein release pattern was influenced by polymer molecular weight and composition. The release rate of PLA(Mw 100,000) microsphere was higher than any other microspheres. In consequence of the hydrolysis of PLGA(50:50) microspheres, environmental pH decreased from 7.4 to 5.0. The PLA, PLGA (75:25) and PLGA (85:15) microshperes showed no significant pH change. The antigenicity or n in microshperes was assayed by indirect sandwich ELISA using equine polyclonal tetanus antitoxin for capture antibody and human polyclonal tetanus antitoxin for primary antibody. The antigenicity of TT in PLA (Mw 100,000), PLGA(50:50, Mw 100,000) and PLGA (75:25, Mw 73,300) after 30 days incubation showed 54, 40.9 and 76.7%, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.29-30
• /
• 2007

In a device structure of ITO/tris(8-hydroxyquinoline) aluminum $(Alq_3)$/Al device, We investigated an the electrical characteristics of Organic Light-Emitting Diodes (OLEDs) depending on the hole-size of boat. The device was manufactured using a thermal evaporation under a base pressure of $5{\times}10^{-6}$ [Torr]. The $Alq_3$ organics were evaporated to be 100 [nm] thick at a deposition rate of $1.5[{\AA}/s]$, and in order to investigate the optimal surface roughness of $Alq_3$, the $Alq_3$ was thermally evaporated to be 0.8 [mm], 1.0 [mm], 1.5 [mm], and 3.0 [mm] as a hole-size of the boat respectively. We found that when the hole-size of the boat is 1.0 [mm], luminance and external quantum efficiency are superior.

• 한국재료학회지
• /
• 제28권12호
• /
• pp.748-757
• /
• 2018

Inorganic semiconductor compounds, e.g., CIGS and CZTS, are promising materials for thin film solar cells because of their high light absorption coefficient and stability. Research on thin film solar cells using this compound has made remarkable progress in the last two decades. Vacuum-based processes, e.g., co-evaporation and sputtering, are well established to obtain high-efficiency CIGS and/or CZTS thin film solar cells with over 20 % of power conversion. However, because the vacuum-based processes need high cost equipment, they pose technological barriers to producing low-cost and large area photovoltaic cells. Recently, non-vacuum based processes, for example the solution/nanoparticle precursor process, the electrodeposition method, or the polymer-capped precursors process, have been intensively studied to reduce capital expenditure. Lately, over 17 % of energy conversion efficiency has been reported by solution precursors methods in CIGS solar cells. This article reviews the status of non-vacuum techniques that are used to fabricate CIGS and CZTS thin films solar cells.

• 마이크로전자및패키징학회지
• /
• 제10권1호
• /
• pp.1-5
• /
• 2003

본 연구에서는 ITO (indium tin oxide)/glass 투명기판 위에 다층구조의 OELD (organic electroluminescent devices) 소자를 진공 열증착법으로 제작하였다. 발광층 재료로서 Alq$_3$(tris-(8-hydroxyquinoline)aluminum)물질을 사용하였고, 정공수송층으로는 TPD (triphenyl-diamine) 및 $\alpha-NPD$를 사용하였다. 정공주입층 재료로서 CuPc (Copper phthalocyanine)를 사용하였다. 또한 QD2(quinacridone2) 물질을 $Alq_3$ 발광층내에 약 $10\AA$ 두께로 증착하여 발광효율 향상을 시도하였다. 제작된 모든 소자의 발광개시전압은 약 7 V 이었으며, 정공수송층으로 TPD 물질대신에 열적안정성이 우수한 $\alpha-NPD$를 사용한 경우 휘도값과 발광효율이 개선되었다. $Alq_3$ 발광층 사이에 QD2 물질을 적층한 소자에서 발광효율은 1.55 lm/W 값을 나타내어 $Alq_3$ 발광층만을 사용한 경우에 비해 약 8배 발광효율이 향상되었다.

• Current Photovoltaic Research
• /
• 제7권4호
• /
• pp.103-110
• /
• 2019

Cu(In,Ga)₃Se₅ (β-CIGS) has a band gap of 1.35 eV, which is an optimum value for high solar-energy conversion efficiency. The effects of Cu and Ga content on the cell performance were investigated previously. However, the effect of Se content on the cell performance is not well understood yet. In this work, β-CIGS films were fabricated by three-stage co-evaporation of elemental sources with various Se fluxes at the third stage instead of at all stages. The average composition of five samples was Cu_1.05(In_0.59,Ga_0.41)3Se_y, where the stoichiometric y value is 5.03 and the stoichiometric Se/metal (Se/M) ratio is 1.24. We varied the Se/metal ratio in a range from 1.18 to 1.28. We found that the best efficiency was achieved when the Se/M ratio was 1.24, which is exactly the stoichiometric value where the CIGS grains on the CIGS surface were tightly connected and faceted. With the optimum Se/M ratio, we were able to enhance the cell efficiency of a β-CIGS solar cell from 9.6% to 12.0% by employing a Na₂S post deposition treatment. Our results indicate that Na₂S post deposition treatment is very effective to enhance the cell efficiency to a level on par with that in α-CIGS cell.

• 한국재료학회지
• /
• 제20권6호
• /
• pp.294-300
• /
• 2010

In this study, we fabricated a polymer light emitting diode (PLED) and investigated its electrical and optical characteristics in order to examine the effects of the PFO [poly(9,9-dioctylfluorene-2-7-diyl) end capped with N,N-bis(4-methylphenyl)-4-aniline] concentrations in the emission layer (EML). The PFO polymer was dissolved in toluene ranging from 0.2 to 1.2 wt%, and then spin-coated. To verify the influence of the TPBI [2,2',2"-(1,3,5-Benzinetriyl)-tris(1-phenyl-1-H-benzimidazole)]electron transport layer, TPBI small molecules were deposited by thermal evaporation. The current density, luminance, wavelength and current efficiency characteristics of the prepared PLED devices with and without TPBI layer at various PFO concentrations were measured and compared. The luminance and current efficiency of the PLED devices without TPBI layer were increased, from 117 to $553\;cd/m^2$ and from 0.015 to 0.110 cd/A, as the PFO concentration increased from 0.2 to 1.0 wt%. For the PLED devices with TPBI layer, the luminance and current efficiency were $1724\;cd/m^2$ and 0.501 cd/A at 1.0 wt% PFO concentration. The CIE color coordinators of the PLED device with TPBI layer at 1.0 wt% PFO concentration showed a more pure blue color compared with the one without TPBI, and the CIE values varied from (x, y) = (0.21, 0.23) to (x, y) = (0.16, 0.11).

• Journal of Pharmaceutical Investigation
• /
• 제36권6호
• /
• pp.355-361
• /
• 2006

Intraarticular corticosteroid injections for therapy of rheumatic arthritis are administered with the aim of optimal local anti-inflammatory effect at the injection site. Since the side effects of corticosteroidal drug, dexamethasone(DEX), administered at hish dose limited the therapeutic efficacy, there was a need to design a new drug delivery system for controlled release of dexamethasone. As a prodrug for continuous therapeutic efficacy, dexamethasone-21-palmitate(DEX-PAL) was prepared via esterification of palmitoyl chloride and dexamethasone. DEX-PAL was identified by NMR and MASS analysis. DEX-PAL or DEX was entrapped in lipid nanosphere which could be prepared by using a self emulsification-solvent evaporation method. Physicochemical characteristics such as mean particle diameter, zeta potential and drug loading efficiency of the lipid nanospheres were investigated with variation of either the kind of lipid or the lipid composition. The lipid nanospheres had a mean diameter $83{\sim}95$ nm and DEX-PAL loading efficiency of up to 95%. The drug loading efficiency increased with the increase of aliphatic chain length attached to the phospholipid. The incorporation of cationic lipid was very efficient for both reducing particle size of lipid nanospheres and enhancing drug loading efficiency. The lipid nanospheres containing DEX-PAL may be a promising novel drug carrier for the controlled release of the poorly water-soluble drugs.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2009년도 춘계학술발표대회 논문집
• /
• pp.230-234
• /
• 2009

It is significant technique to increase competitiveness that solar cells have a high energy conversion efficiency and cost effectiveness. When making high efficiency crystalline Si solar cells, evaporated Ti/Pd/Ag contact system is widely used in order to reduce the electrical resistance of the contact fingers. However, the evaporation process is no applicable to mass production because high vacuum is needed. Furthermore, those metals are too expensive to be applied for terrestrial applications. Ni/Cu/Ag contact system of silicon solar cells offers a relatively inexpensive method of making electrical contact. Ni silicide formation is one of the indispensable techniques for Ni/Cu/Ag contact sytem. Ni was electroless plated on the front grid pattern, After Ni electroless plating, the cells were annealed by RTP(Rapid Thermal Process). Ni silicide(NiSi) has certain advantages over Ti silicide($TiSi_2$), lower temperature anneal, one step anneal, low resistivity, low silicon consumption, low film stress, absence of reaction between the annealing ambient. Ni/Cu/Ag metallization scheme is an important process in the direction of cost reduction for solar cells of high efficiency. In this article we shall report an investigation of rapid thermal silicidation of nickel on silngle crystalline silicon wafers in the annealing range of $350-390^{\circ}C$. The samples annealed at temperatures from 350 to $390^{\circ}C$ have been analyzed by SEM(Scanning Electron Microscopy).

• 한국연초학회지
• /
• 제28권2호
• /
• pp.117-123
• /
• 2006

The pulping process in a papermaking process for a reconstituted tobacco sheet (RECON) was evaluated. For the practical information, the experiments were conducted in a real mill. Two pulping conditions were chosen and changed depending on the feasibility, such as the pulping temperature and the properties of pulping water. The higher pulping temperature resulted in the easier dissolution of solubles from the raw materials. However, the efficiency of screw press process was decreased by the higher pulping temperature, which resulted in the reduction of the HWS and the concentration in the #1 screw press filtrate. The addition of SEL(Strong extracted liquor) to pulper affected the efficiency of dissolution and the final concentration of #1 screw press filtrate. Although the higher SEL resulted in the less dissolution of the solubles from the raw materials, the concentration of the #1 screw press filtrate was greatly increased by the higher addition of SEL, which could provide much better efficiency to the following evaporation process of the filtrate and could increase the whole productivity.