• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1991.10a
• /
• pp.12-16
• /
• 1991

Cadmium sulphide films with thickness of 0.6∼1.2$\mu\textrm{m}$ were deposited onto corning 7059 glass substrate under a vacuum of 5${\times}$10$\^$-6/ Torr. Source and substrate temperature ranges used were 800∼1100$^{\circ}C$ and 100∼200$^{\circ}C$, respectively. The microstructures and semiconducting properties of the films were studied using X-ray diffraction, UV-VIS-IR spectrophotometer and Hall measurement unit. Electrical resistivity and optical transmission of the CdS films decrease with an increase in source temperature while they increase with an increase in substrate temperature. The resistivity of the film evaporated at 1100$^{\circ}C$ varied from 7${\times}$10$^3$ohm-cm at the substrate temperature of 100$^{\circ}C$ to 2${\times}$10$\_$6/ohm-cm at 190$^{\circ}C$. All the films had hexagonal structure and strong texture with c-axis of grains normal to the substrate glass.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.1
• /
• pp.59-66
• /
• 2003

The purpose of this study is to analyze the characteristics (COP) of the heat pump system for various operating conditions with the use of seawater heat source and exhaust energy. To accomplish the goal, first of all, the computer simulation for heat pump system is carried out. The heat pump system model is made of a waste heat recovery system and a vapor compression refrigeration system, and the working fluid is R-22. The model calculated the change of COP with the variation of temperature and flow rate. The COP and the plate heat exchanger (PHE) area of the heat pump system are considered moderately high in the condensation temperature of $25^{\circ}^C$ and the evaporation temperature of $2^{\circ}^C$ in indoor culture system. The simulation results will be used effectively for the design and the performance prediction of heat pump system using unused energy in a land base aquaculture system.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.497-497
• /
• 2012

산업의 발전함에 따라 고기능성 박막의 수요가 증가하고 있으며, magnetron sputtering, e-beam evaporation, ion beam 등을 이용한 박막 증착에 대한 연구가 많이 진행되고 있다. 그러나 기존 방법만으로는 박막 접착계면의 불균일로 인해 고기능성 박막 성장이 어렵다는 단점을 가지고 있다. 이러한 문제를 해결하기 위하여 박막 공정 중 고밀도 플라즈마 소스(high density plasma source)를 통해 추가적인 에너지를 인가하여 박막의 밀도를 bulk 수준으로 증가시키고 내부 응력을 조절하는 연구에 대한 관심이 커지고 있다. 특히 grid를 이용하여 플라즈마 내 이온의 입사에너지를 증가시킴으로써, 기존 공정보다 고기능성 박막을 구현할 수 있다. 본 연구에서는 RF power를 이용한 inductively coupled plasma를 통해 플라즈마를 생성시킨 후 grid에 DC power를 인가하는 플라즈마 소스를 개발하였으며, 시뮬레이션을 통해 plasma density와 ion current density, ion energy 분석 및 grid 디자인을 하였다. 개발된 플라즈마 소스는 ion energy analyzer를 통해 RF power 및 grid에 인가하는 power의 세기에 따라 이온화 정도 및 이온의 입사에너지를 측정하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.6
• /
• pp.607-613
• /
• 2010

A seawater distiller, in which the waste heat from a portable electric generator was used, with a multiple-effect diffusion still was designed. The waste gas from small generators commonly used in islands has not yet been used because it has less thermal energy; however, this waste gas can be used as a heat source for small-capacity distillers and as an additional heat source for solar stills. The proposed distiller comprises a series of closely spaced parallel partitions that are placed in contact with saline-soaked wicks. In the distiller, evaporation and condensation processes are repeated to recycle the thermal energy for increasing the distillate productivity. Experimental results show that the proposed distiller with only one-effect still can produce at least 6.7 kg/day of distilled water; the proposed distiller with a ten-effect still is expected to produce 43 kg/day of distilled water. This amount of distillate is approximately four times the maximum daily productivity of the solar stills, as determined in outdoor experiments.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.130-131
• /
• 2011

박막의 제조는 많은 연구의 가장 기초가 되는 시편을 만드는 과정으로 현대의 과학기술에서 매우 중요한 공정 중의 하나이다. 그러나 이러한 박막의 제조는 제조하는 사람의 숙련도나 장치에 의존하며 경우에 따라서는 원하는 특성의 박막을 제조하는 것이 매우 어려운 작업이 되기도 한다. 따라서 경험이 없는 연구자의 경우는 때때로 까다로움과 번거로움을 느끼게 되며, 안정된 공정을 찾기까지 많은 시간을 소비 하게 된다. 특히 부적절한 증발방법의 선정에 따른 실험 결과는 경제적인 손실을 초래할 뿐만 아니라 실험하는 사람을 좌절시키는 가장 큰 요인이 되어왔다. 진공증착에 의한 박막의 제조는 증발법과 스퍼터링, 이온플레이팅 등의 방법이 있으며 이중 증발을 이용한 박막의 제조에는 저항가열 증발, 전자빔 가열 증발, 유도가열 증발 등의 방법으로 구분하고 있다. 저항가열 증발원은 가격이 저렴하다는 장점은 있으나 증발원이 손쉽게 파손되거나 증발량이 일정하지 않아 박막의 정밀 제어가 어려울 뿐만 아니라 때에 따라서는 1 ${\mu}m$ 이상의 후막 형성에도 어려움이 있는 등 많은 제약이 있다. 따라서 적절한 증발원의 선정이 실험의 효율성을 좌우하는 경우가 많다. 적절한 증발원의 선정과 효율적인 실험을 위해 증발원 제조회사에서는 증발원의 선정과 증발 조건과 관련된 자료를 카탈로그 형태로 발행하고 있다. 그러나 그러한 자료만으로는 객관적인 정보를 얻기에 충분하지 못한 경우가 많으며, 어떤 경우에는 저자 등의 경험과 일치하지 않는 정보도 포함하고 있었다. 전자빔 증발원은 냉각이 되는 Crucible에 물질을 담고 고전압의 전자빔으로 물질을 가열시켜 증발시키는 증발원으로 1960년대 이후 박막 제조 실험에 이용되기 시작하였다. 전자빔은 고순도의 피막 제조가 가능하고 증발물질의 교체가 쉬우며 고속 증발이 가능함은 물론 다층막의 제조가 용이하고 증발물질의 제조비용이 저렴하다는 장점이 있다. 이러한 장점 때문에 1970년대 이후에는 전자빔을 이용한 박막제조가 폭 넓게 이루어졌고 이때를 즈음하여 전자빔을 이용한 물질의 증발 특성이 논문으로 발표되기도 하였다. 본 연구에서는 증발에 관한 저자들의 경험을 바탕으로 저항가열과 전자빔을 이용하여 증발실험을 진행한 물질계를 중심으로 각 물질의 증발특성과 가장 효율적인 Liner 등에 대해 기술하였다. 특히, 각종 물질의 증발 특성을 체계화함은 물론 효율적인 증발 방법을 객관적인 Data와 함께 제공하여 효과적인 박막 제조 실험에 도움이 되고자 하였다.

• Journal of Power System Engineering
• /
• v.21 no.2
• /
• pp.64-69
• /
• 2017

The purpose of this study is to investigate the performance characteristics of seawater cooling system for a fishing vessel. The circulation amount of refrigerant, condensation capacity, evaporation capacity, compression work and coefficient of performance(COP) were analyzed as the heat source temperature changed. The experimental setup consisted of an open-type compressor, a shell&tube type condenser, an evaporator and an expansion valve. The heat source was controlled by a constant temperature chamber. The main results of this study are summarized as follows. The condensation capacity increased with increasing heat source temperature, and it was confirmed that the effect of circulating amount of refrigerant was dominant. The amount of heat for vaporization was almost constant even though the temperature of the heat source increased. On the other hand, the compression power was increased. This is because the compression ratio increases as the condensation pressure, the enthalpy difference between inlet and outlet, the amount of circulating refrigerant increases. The performance coefficient of this system showed a tendency decreasing with increasing heat source temperature. Therefore, the basic data of the seawater cooling system for the maintenance of the catch line of the shore fishing boats was acquired through this study, and it is considered that it will be sufficient for the actual design.

• Journal of the Korean Ceramic Society
• /
• v.41 no.6
• /
• pp.450-455
• /
• 2004

NiCr thin films were fabricated by thermal evaporation method using NiCr alloy as evaporating source. NiCr thin films were annealed at various temperatures in air atmosphere in order to investigate effects of annealing conditions on phase change, composition, and microstructures of NiCr films. Typical multilayer was formed after annealing in air atmosphere. This results from the diffusion and oxidation of Cr toward surface during annealing. In the case of annealing at 700$^{\circ}C$, large columnar grains of NiO were formed on Cr-oxide layer through the diffusion and oxidation of Ni over Cr-oxide layer. Especially, NiO layer was formed additionally on surface, sustaining the underlayer structure with the formation of porous Ni layer.

• Journal of the Korean Ceramic Society
• /
• v.45 no.9
• /
• pp.524-530
• /
• 2008

Anti-Reflective (AR) thin film coatings of $SiO_2$ (n= 1.48) and $TiO_2$ (n=2.17) were deposited by ion-beam assisted deposition (IBAD) with End-Hall ion source and conventional electron beam (e-beam) evaporation to investigate the effect of deposition method on the refractive indicies (n) of the fIlms. Green-light generation using a GaAs laser diode was achieved via excitation of the second harmonic. The latter resulted from the transmission of the fundamental guided-mode wave of 1064 nm through periodically poled $LiNbO_3$. Large differences in the refractive indicies of each of the layers in the multilayer coating may improve AR performance. IBAD of $SiO_2$ reduced its refractive index from 1.45 to 1.34 at 1064 nm. Conversely, e-beam evaporation of $TiO_2$ increased its refractive index from 1.80 to 2.11. In addition, no fluctuations in absorption at the wavelength of 1064 nm were found. The results suggest that films prepared by different deposition methods can increase the effectiveness of multilayer AR coatings.

• Journal of Power System Engineering
• /
• v.17 no.6
• /
• pp.102-107
• /
• 2013

In this paper, the performance analysis for evaporation capacity, total work and efficiency of the ocean thermal energy conversion(OTEC) power system using mixed refrigerant(R32,R152a) is conducted to find the effect of hot wasted water on OTEC power system. The system in this study is applied with two stage turbine, regenerator, cooler and separator on Organic Rankine Cycle. The commercial program HYSYS is used for the performance analysis. The main results were summarized as follows : The efficiency of the OTEC power cycle has a largely effect on the evaporation capacity and total work. As increasing temperature of heat source water, evaporator's capacity is decreased but total work increase. Otherwise, using hot wasted water bring effects not only increasing system efficiency but also declining evaporator's capacity. Thus With a thorough grasp of these effect, it is necessary to find way to use hot wasted water emitted by power plant and so on.

• Electrical & Electronic Materials
• /
• v.7 no.3
• /
• pp.243-251
• /
• 1994

ITO(Indium Tin Oxide) film with thickness of 1500.angs. was prepared by an e-beam evaporator onto a glass and a p-type InP wafer (100) LEC grown Zn-doped p=2.3*10$\^$16/cm$\^$-3/), in which the components of ITO used for evaporation source were hot pressed pellets 1 mole% ln$\_$2/O$\_$3/+9 mole% SnO$\_$2/, and evaporated in O$\_$2/ ambient. The optimum conditions to preparation of ITO thin film were the substrate temperature of 350.deg. C, the injected oxygen pressure of 2*10$\^$-4/ torr, and the evaporation speed of 0.2-0.3.angs./sec, respectively. In these optimum conditions, the resistivity and the carrier concentration were 5.3*10$\^$-3/ .ohm.-cm, 6.5*10$\^$20/cm$\^$-3/, and the transmittance was over 80%. From the results of J-V measurements in ITO/p-InP structure solar cells, the higher pressure of injected oxygen, the more open circuit voltage. The efficiency of ITO/p-InP solar cell without the grid line contact, prepared by the optimum evaporation conditions, was 7.19%. By using the grid line contact, the efficiency, the open circuit voltage, the short circuit current density, the fill factor, the series resistance, and the shunt resistance were 8.5%, 0.47V, 29.48 mAcm$\^$-2/ , 61.35%, 3.ohm., and 26.6k.ohm., respectively.