• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.11
• /
• pp.1672-1678
• /
• 1989

Major problems preventing the device-quality GaAs/Si heterostructure are the lattice mismatch of about 4% and difference in thermal expansion coefficient by a factor of 2.64 between Si and GaAs. Ge is a good candidate for the buffer layer because its lattice parameter and thermal expansion coefficient are almost the same as those of GaAs. As a first step toward developing heterostructure such as GaAs/Ge/Si entirely by a home-built PAE (plasma-assisted epitaxy), Ge films have been deposited on p-type Si (100)substrate by the plasma assisted evaporation of solid Ge source. The characteristics of these Ge/Si heterostructure were determined by X-ray diffraction, SEM and Auge electron spectroscope. PAE system has been successfully applied to quality-good Ge layer on Si substrate at relatively low temperature. Furthermore, this system can remove the native oxide(SiO2) on Si substrate with in-situ cleaning procedure. Ge layer grown on Si substrate by PAE at substrate temperature of 450\ulcorner in hydrogen partial pressure of 10mTorr was expected with a good buffer layer for GaAs/Ge/Si heterostructure.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.12
• /
• pp.1140-1143
• /
• 2006

We report on the fabrication of P3HT-based thin-film transistors (TFTs) for liquid crystal display that consist of $NiO_x$, poly-vinyl phenol (PVP), and Ni for the source-drain (S/D) electrodes, gate dielectric layer, and gate electrode, respectively The $NiO_x$ S/D electrodes of which the work function is well matched to that of P3HT are deposited on a P3HT channel by electron-beam evaporation of NiO powder. The maximum saturation current of our P3HT-based TFT is about $15{\mu}A$ at a gate bias of -30 V showing a high field effect mobility of $0.079cm^2/Vs$ in the dark, and the on/off current ratio of our TFT is about $10^5$. It is concluded that jointly adopting $NiO_x$ for the S/D electrodes and PVP for gate dielectric realizes a high-quality P3HT-based TFT.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.918-919
• /
• 2015

Because of environmental regulations in emissions control area, the demand for ships to use LNG as fuel is increasing. Orders for domestic shipbuilders to produce LNG carriers are steadily increasing. However, major appliances such as spray pump, main cargo pump and others have been relied on imports. Therefore, development of pump motor using at cryogenic temperature is necessary. Operating temperature of an induction motor is at $-163^{\circ}C$. At this low temperature, the resistivity of a motor coil is quite different from normal ones, and so does the torque characteristics of motor. This paper presents a designing method of a cryogenic induction motor for LNG pump. The variation of resistivity of motor coil is considered in the design process. The heat source such as core-loss, hysteresis-loss and copper-loss are analyzed to prevent the LNG evaporation which may cause the motor failure.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.628-631
• /
• 2002

$Al_2O_3$ capping layer and MgO protective layer were deposited by electron beam evaporation method using single crystal source. Thickness of the capping layer, $Al_2O_3$, was varied from 5 nm to 10 nm. Surface morphology was observed by SEM and AFM before and after hydration. And microstructure of deposited $Al_2O_3$ layer and chemical shift of electron binding energy were also observed by high resolution TEM and XPS, respectively, after hydration. From these results, it was found that Mg atoms diffused into $Al_2O_3$ layer, reacted with moisture and formed $Mg(OH)_2$ during hydration. As thickness of $Al_2O_3$ increased, extent of hydration increased. $Al_2O_3$ capped MgO thin films and uncapped MgO thin films were deposited on AC-PDP test panel to characterize discharge properties. Although $Al_2O_3$ has poor discharge properties rather than MgO, because of many hydrated species on the surface of MgO, similar discharge properties were observed.

• Journal of ILASS-Korea
• /
• v.14 no.2
• /
• pp.71-76
• /
• 2009

The aim of this investigation is to study the effect of the high injection pressure on the dimethyl ether (DME) spray characteristics injected through a common-rail diesel injector under various ambient pressures. In order to investigate the effect of the injection pressure and ambient condition, the common-rail injection system with two high pressure pumps and high pressure chamber pressurized up to 40 bar were used, respectively. Spray images of DME fuel obtained from a visualization system composed of high speed camera and two metal halide lamps as the light source. From the obtained images, the spray behaviors such as a spray development process, spray tip penetration, spray width, and spray cone angle were measured for analyzing the DME spray characteristics under various experimental conditions. It was found that the spray development slowed as the ambient pressure increased and spray tip penetration at injection pressure of 90 MPa is longer than that at 50 MPa. In addition, the spray width at the end stage of injection decreased under the atmospheric conditions due to the evaporation property of DME fuel, and DME spray shows narrow spray cone angle according to the injection pressure increased.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1546-1548
• /
• 2002

In this paper, the electrical characteristics of pentacene thin film transistors(TFTs) with stacked and surface-treated gate insulators have been investigated. The semiconductor layer of pentacene was thermally evaporated onto the stacked gate insulators. For the gate insulating materials. PVP(PolyvinylPhenol) and polystyrene were spin-coated with two different stacking orders, PVP-polystyrene and polystyrene-PVP. Rapid solvent evaporation during the spin-coating processes of these insulating layers produces non-equilibrium phase morphologies accompanied by surface undulations on gate insulator interfaces. This non-equilibrium phase morphology affects the growth mode of the subsequent pentacene layer. Therefore, in order to smoothen the gate dielectric surfaces, gate dielectric surfaces were rubbed laterally along the direction from the drain to the source TFTs with with stacked and surface-treated gate insulators have provided improved operational characteristics.

• Journal of Energy Engineering
• /
• v.25 no.3
• /
• pp.59-65
• /
• 2016

MVR evaporation is a method of pressurizing the evaporating steam to raise its temperature with an electric compressor instead of burning fuel and reusing the heat source through the embraced heat exchanger to minimize energy use. MVR desalination system with wind power uses varying wind power instead of stable electricity and can flexibly control the volume of fresh water production. The present study introduces the design, construction and operation of a MVR desalination system of 30ton/day capacity. Experimental results, MVR compression ratio is higher than 1.5, temperature difference of the main heat exchanger is $5{\sim}7^{\circ}C$. This value shows the same performance as the designed value.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.150-150
• /
• 2012

진공증착을 이용하여 제조된 알루미늄 박막은 증착 조건에 따라 그 특성이 현저히 달라지는 것으로 알려져 있다. 특히, 진공도와 증착율에 따라 비저항과 반사율, 표면 색상 등이 크게 달라지며 이에 따라 적절한 증발원 및 증착 방법의 선택이 박막의 특성을 좌우하게 된다. 알루미늄은 융점이 낮은 반면 증기화되는 온도가 높을 뿐만 아니라 고온에서는 대부분의 내화물 금속과 반응하기 때문에 저항가열 증발원을 이용하여 증발시키기가 매우 까다로운 물질중의 하나이다. 또한 전자빔으로 증발시킬 경우에는 열전도도가 커서 수냉 도가니를 통해 열이 빠져나가기 때문에 효과적인 증발을 위해서는 고전력을 투입해야 하는 어려움이 있다. 한편, 스퍼터링 증발원을 이용하여 알루미늄을 증착하면 낮은 증착율로 인해 반사율과 같은 제반 특성이 현저히 떨어지는 단점이 있다. 본 논문에서는 알루미늄 박막의 제조를 위한 최적의 증발원과 증착 방법을 소개하고 증착 조건과 박막 특성의 상관성 자료를 소개하였다. 이를 위해 각종 저항가열 및 전자빔 증발원 그리고 스퍼터링을 이용한 증발 실험 결과를 소개하고 증발원에 따른 알루미늄 박막의 특성 변화 그리고 제반 증착 조건이 박막의 특성에 미치는 영향을 소개하였다.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.56 no.1
• /
• pp.18-22
• /
• 2011

Study on extraction and color characteristics of mulberry fruit pigment(C3G; cyanidin-3-glucoside) was performed to increase utilization as new source of natural food colorant. C3G was extracted with 0.1 % citric acid-70% EtOH. Then it was evaporated with large scale evaporation system. After adding dextrin to C3G concentration materials, we made pigment powder with freezing dryer.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.3
• /
• pp.28-36
• /
• 2000

Spray characteristics of diesel fuel injection is one of the most important factors in diesel combustion and pollutant emissions especially in HSDI (High Speed Direct Injection) diesel engines where the interval between the onset of combustion and the evaporation of atomized fuel is relatively short, An investigation into various spray characteristics from different holes of VCO(Valve Covered Orifice) nozzles was performed and its results were compared to standard sac nozzle. The global characteristics of spray, including spray angle, spray tip penetration, and spray pattern were measured from the spray images which were frozen by an instantaneous photography with a spark light source. For better understanding of spray behavior, SMD of the fuel sprays from multi hole nozzles were measured with back light imaging while the sprays from the other holes are covered by a purpose-built nozzle cap. The investigation manifestly reveals the different spray patterns at the beginning of injection produced by VCO nozzles can be identified as three distinct types with their own macroscopic and microscopic characteristics, while macroscopic non-uniformity disappears at 0.9∼1.0ms from the start of injection.