• Transactions of Materials Processing
• /
• v.7 no.4
• /
• pp.400-406
• /
• 1998

The press formability analysis of welding parts was studied in the current work by the tailor welded blank. The press formability was tested by means of the flash weldability and the formability for two kinds of materials (SPCC & S35C). The results indicate that SPCC & S35C steel sheets showed good weldability and formability after an optimum welding conditions. The independent operation variables were characterized by strength of welding parts, deformation after the welding, press formability of welding parts and productibility of welding. The weldability and the quality of welding parts of the flashed SPCC steel sheet was superior to those of the S35C steel sheet, since a higher carbon content in steel sheet led to a higher hardness. The experimental results were discussed by the evaluation of the results obtained from tensile test, hardness test, micro-structure and V bending test.

• Structural Engineering and Mechanics
• /
• v.20 no.3
• /
• pp.335-346
• /
• 2005

The T-stress of cracks in elastic sheets is solved by using the fractal finite element method (FFEM). The FFEM, which had been developed to determine the stress intensity factors of cracks, is re-applied to evaluate the T-stress which is one of the important fracture parameters. The FFEM combines an exterior finite element model with a localized inner model near the crack tip. The mesh geometry of the latter is self-similar in radial layers around the tip. The higher order Williams series is used to condense the large numbers of nodal displacements at the inner model near the crack tip to a small set of unknown coefficients. Numerical examples revealed that the present approach is simple and accurate for calculating the T-stresses and the stress intensity factors. Some errors of the T-stress solutions shown in the previous literature are identified and the new solutions for the T-stress calculations are presented.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.331-334
• /
• 2003

Since regulation or specification for the reinforcing method are quite ambiguous, structural design for the reinforcement can be subjectively and arbitrarily conducted. Thus, reasonable limitation and guide for the quantity of the reinforcement are required for the safe use of the structure after repair. In order to guarantee the safety of the structural member several items should be considered; reinforcing limit to avoid the brittle failure, least required strength of the existing member before reinforcement in order not to fail under the new serviceability load condition when reinforcing steel plates or CFRP sheets are harmed or subjected to fire.

• Journal of Korean Home Economics Education Association
• /
• v.14 no.1
• /
• pp.75-86
• /
• 2002

The purpose of this study is to analyze the effect of Web-based small group discussion on the achievement and satisfaction in the practice-planning phase of Technology and Home Economy. The subject of this study consists of 68 students of a middle school. The 7r7up is divided into two subgroup. the Web-based discussion croup and the face-to-face discussion grouts. each of which has 34 students. The achievement is estimated by individual reports. practice plans and the overall evaluation sheets. To estimate the satisfaction of students. the test sheets were used. together with the interviews of sampled students from both group. The results show that there is a statistically significant difference in the performance of practice between the two groups with the significant level of 0.05(p<0.05). There is also some difference in the satisfaction between the two groups.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.3
• /
• pp.8-13
• /
• 2002

In order to obtain the basic informations for the development of high strength and high weldability aluminum alloy sheets, the experimental study was carried out to evaluate resistance spot welding characteristics and welding parameters (welding current, welding time, electrode force) far the aluminum alloy sheets. The mechanical properties of spot weld of aluminum alloy were evaluated by tensile shear test and by peel test at room temperature and also the welding possible zone was established through variation of current electrode force and welding time.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.195-198
• /
• 2009

In this study, in order to get the forming limit of AHSS sheet in the negative minor strain region, the shapes of die corner and drawbead are redesigned by employing the Taguchi's design of experiment method and the FEM forming simulation. With the redesigned FLD tool, the forming limit tests of automotive multi-phase(Dual Phase and Complex Phase) steel sheets which induce the normal fractures on the blank are performed.

• Transactions of Materials Processing
• /
• v.12 no.5
• /
• pp.504-512
• /
• 2003

The plastic strain ratios(R-values) of low carbon steel sheets were determined by the automatic strain measurement method using two extensometers, the indirect photo method for the same tensile specimen during tensile test and the indirect method for the specimen after tensile test. The experimental results showed that the measured plastic strain ratios from the automatic strain measurement method using two extensometers coincided with those from the indirect photo method and the indirect method for all tensile specimens. In addition, the strain dependence of plastic strain ratios could be continuously recorded and the anisotropy of the strength coefficient, K, and strain hardening exponent, n, could be automatically calculated in three directions by computer through the use of two extensometers. The experimental results showed that the strain dependence of R-value was related to the anisotropy of strain hardening exponent in low carbon steel sheets.

• Journal of Welding and Joining
• /
• v.22 no.5
• /
• pp.32-37
• /
• 2004

Application of bonding by adhesives can be found in many industries, particularly in advanced technological domains such as aeronautical and space, automobile and electronics industries. Periodic inspection with conventional ultrasonic NDE techniques is capable of indicating the presence and possible location of crack. Continuous ultrasonic attenuation monitoring has potential to supply information. This article discusses the use of pulse-echo ultrasonic testing for the inspection of adhesive bonds between metal sheets. The method is based on the measurement of the reflection coefficient at the metal/adhesive interface. By means of a control experiment it is shown that Quantitative Nondestructive Evaluation in Adhesive Joints are evaluated together with Ultrasonic Testing and Fracture Testing.

• The Journal of the Korea Contents Association
• /
• v.2 no.4
• /
• pp.76-84
• /
• 2002

The conventional database evaluation method is carried out by the way in which the person in charge of each specialty database(DB manager) composes the evaluation sheets for corretionㆍrevision on the already-constructed database in a manual method and carries out the measurement and re-education of DB workers based upon it. As a result, that way consumes much time on career information and measurement works about DB workers, causing low time and cost efficiency and lack of systematic management of DB workers, resulting in becoming the hindrance factor of databases quality improvement. This research provides on-line, red-time results of measurements about the efficiency of DB production and DB workers by combining the static measurement with dynamic measurement by DB manager, both of which utilize the System. Therefore, the DB manager can contribute to the improvement of DB quality by determining the continuation of DB production by DB workers or carrying out the re-education of DB workers without being affected by time or spacial constraints.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.28 no.1
• /
• pp.147-157
• /
• 2005

The purpose of this study is to develope the model of economy analysis and evaluation to justify the effect of economic feasibility for constructing ERP system in the company. Since the results for the evaluation of alternatives are influenced by the nature of capital and the circumstances, it is very difficult to evaluate the alternatives and it takes too much time to apply it in the field on account of many alternatives. This study suggests establishment and application of the model on economic analysis and evaluation regarding the nature of capital by using excel spread sheets.