• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.29 no.2
• /
• pp.76-82
• /
• 1997

In paper the evenness of planar distribution of mass in a small scale is called formation (orbetter:mass formation). Traditionally formation has been assessed visually, by looking the sheet of paper against transmitted light. Different kinds of optieal testers are being usd to obtain quantitative rankings htat would be independent of the observer but would well correspond to the visual assessment. However, various raw-material and process factors do influence light trans-mittance in paper and do impair the correspondence between basis weight and the optical formation measurement (or visual assessment). As the optical formation test methods do not incorporate an efficient calib ration routine, the formation of the sophisticated paper grades of today the is rather difficult to measure optically and may lead to erroneous results. It may be concluded that the optical measurement is not suitable for paper grades with high filler content. coating, heavy calendering or that are made of heavily beaten pulp, nordoes it apply for dyed or printed papers. For this reason, visual assessment and optical evaluation shoild be replaced with a measurement that gives reliable results independent on paper grode and manufacturing process. Formation measuremend based on beta radiation is suitable for all paper grades regardless to the material contents or process treatment. It is possible to measure even dyed or printed samples. Thonks to a sim ple and relioble calibration, the results are converted to real basis weight balues that remain reliable even with time. The only beta tester commercially available is the AMBERTEC Beta Formation Tester. Formation of paper does vary locally in the web. Typically there exists a formation profile, too similarly to other properties of paper. Therefore, formation should ？ ays be expressed as a mean of a sufficient amount of parallel determinations. All formation measurements should be calibrated against basis weight.

• Archives of design research
• /
• v.20
• /
• pp.265-276
• /
• 1997

I intend to grope for the desirable outdoor color environment creation plan through researching situation of our apartment houses color environment and grasping the point at issue. The rearch was made that Ilsan(16 items) new city apartment were selected and the color seperately measured such as the dominant, the aid, the accent colors through applied color component ratio was researched by calculating square measure of matched colors and through that the evaluation of apartment complex color environment was formed. The planned construction problems were issued from comparing the planned scheme and the present carrying color status guide by investigating the color plan applied Ilsan new city. The current out apartment outdoor color environment is poor, and the color plan of the early stage has many insufficient parts and many operation errors. For the creation of desirable color environment, the color plan establishment by regional characteristics, the color environment management, though exhaustive color consultation, and the external construction technique improvement, the standard color sheet diffusion, the color understanding of architects, the public relations (P.R), the education on the importance of color are required.

• Journal of Fashion Business
• /
• v.21 no.4
• /
• pp.105-115
• /
• 2017

Continuous lifting and carrying of babies constitutes a serious physical burden, leading to issues such as muscle fatigue and pain in child-care workers. However, there is a lack of research on the pressure and subjective comfort of baby carriers that are commercially available in the market. Therefore, this study was intended to determine the most comfortable and least burdensome type of baby carrier. This was done by analyzing muscle activity and pressure when subjects carried babies using three types of baby carriers. The types of baby carriers evaluated included a 'baby carrier of thin shoulder straps without back support band (X-type)', a 'baby carrier with a back-support band and without a hip sheet (H-type)', and a 'baby carrier with back support band and hip support (H-hip type). The subjective comfort of subjects wearing each type of baby carrier was investigated and compared to the objectively measured data. As a result, the X-type baby carrier showed the heaviest pressure on the shoulders and the subjective comfort was found to not be good. On the waist region, the H-type and H-hip type baby carriers showed significantly less muscle activation than the X-type baby carrier. However, subjects showed a stronger preference for the X-type baby carrier on the waist region, despite greater muscle activation. This appears to be because although the back-support band disperses the weight and thus improves physiological comfort; the wearers feel cramped and thus, lower their psychological comfort.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.5 no.1
• /
• pp.1-8
• /
• 2014

Pultruded glass fiber reinforced polymeric plastic (PFRP) and FRP member manufactured by sheet molding compound (SMC) have superior mechanical and physical properties compared with those of conventional structural materials. Since FRP has an excellent corrosion-resistance and high specific strength and stiffness, the FRP material may be highly appreciated for the development of floating-type photovoltaic (PV) power generation system. In this paper, advanced floating PV generation system made of PFRP and SMC is designed. In the design, it includes tracking solar altitude by tilting photovoltaic arrays and tracking solar azimuth by spinning structures. Moreover, the results of the finite element analysis (FEA) are presented to confirm stability of entire structure under the external loads. Additionally, installation procedure and mooring systems in the Hap-Cheon Dam are discussed and the measurement of strain under the actual circumstances is conducted for assuring stability of actually installed structures. Finally, by comparison with allowable stress, appropriate safety of structure is confirmed to operate the system.

• The Journal of the Korea Contents Association
• /
• v.17 no.12
• /
• pp.191-201
• /
• 2017

The purpose of this study was to examine the learning outcome of problem-based learning as an efficient teaching method to improve the competencies of great talents for future society. A general education course of a university that was one of teaching profession courses titled "prevention of school violence and countermeasures" was provided in the form of PBL, and data were gathered, which were reflective journals, evaluation sheet and observational journals. As a result, PBL produced learning effects such as understanding and applying learning contents, fostering cooperativeness, problem-solving skills and a sense of responsibility, extended thinking and good understanding of PBL. Also, that provided a great opportunity for the students to build up their character by learning caring and by improving cooperativeness, a sense of responsibility and communicative competency, which preservice teachers should have. The findings of the study suggest that the expansion of PBL is necessary to bolster problem- solving skills, self-directed learning, cooperativeness and creativity that are competencies required in the era of the Fourth Industrial Revolution.

• Journal of the Korean Society of Radiology
• /
• v.11 no.4
• /
• pp.189-195
• /
• 2017

Radiation protection equipment has widely used to protect human body from radiations, for example X-ray and gamma ray. The material of the radiation protection equipment is mainly lead (Pb) which has brought out lead poisoning and pollution when the equipment is fallen into disuse. This problem makes research and development find new Pb-free materials for use of radiation protection. Manufacturing and evaluation processes for developing those material were carried out repletely until obtaining the performance of protection rate. In this study, combination possibility of shielding material was studied using Geant4 monte carlo simulation. X-ray tube under the same condition in the real measurement of the protection rate was simulated, and X-ray tube spectrum was obtained. The X-ray tube spectrum was applied to study on the protection rate and lead equivalent. The porosity effect was simulated, and was one of key factors to determine protection rate or lead equivalent in radiation protection sheet of Pb-free.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.111-116
• /
• 2001

Waste office paper, photocopied or laser printed, has recently increased along with office automatization. In waste office paper, toner ink is used as the printing medium in place of conventional oil ink. Since toner ink cannot be saponificated by alkali and be decolored by bleaching, different from the case of oil ink, toner remains on regenerated paper as black specks. Although cascade recycling of waste office paper is compelled at present, the demand for low-grade paper is limited. From such circumstances, a new separation process for waste office paper is demanded to achieve parallel recycling. At the first stage of separation studies, the sharpness of separation is evaluated using small separators to obtain fundamental data. In a lab-scale separator, the sample amount of one feed is generally a few grams. However, the sample amount used for brightness, ERIC, and image analysis that are generally used to evaluate the efficiency of deinking are not small for lab-scale tests of these analyses. This paper describes an investigation of a sheet preparation method by a small amount of sample under 0.5g and compares the precision of toner content determination of spectroscopic analysis and image analysis from the viewpoint of separation evaluation. The easiness and convenience of the operation using only general-purpose equipments has also been set as a principle purpose. From the viewpoint of an analysis that yields high precision with a small amount of sample in short time, the method calculating the absorption coefficient from diffuse reflectance in the visible region is the most rational method in this study.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.7 no.3
• /
• pp.79-88
• /
• 2003

For the construction of PC bridge piers the implementation of 1992 seismic provisions, longitudinal steels were practically lap-spliced in the plastic hinge region. Experimental investigation was conducted ductility of evaluate the seismic earthquake-experienced reinforced concrete columns with 2,5 aspect ratio. Six test specimens were mode with test parameters: confinement ratios, lap splices, and retrofitting FRP materials. They were damaged under series of artificial earthquakes that could be compatible in Korean peninsula. Directly after the pseudo-dynamic test, damaged columns were retested under inelastic reversal cyclic loading simultaneously under a constant axial load, P＝0.1f$\_$ck/A$\_$g/. Residual seismic performance of damaged columns was evaluated and compared to that of the corresponding original columns. Test results show that PC bridge piers with lap-spliced longitudinal steels appeared to fail at low ductility. This was due to the debonding of the lap splice, which resulted from insufficient development of the longitudinal steels. The specimens externally wrapped with composite FRP straps in the potential plastic hinge region indicated significant improvement both in flexural strength and displacement ductility.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.5
• /
• pp.571-578
• /
• 2014

As a way of developing wooden joint development, a glass fiber reinforced wood plate was manufactured to replace a steel plate. Also, the fracture toughness was evaluated. Through application to a cantilever-type specimen made of a column and a beam, the moment resistance performance was evaluated. For the fracture toughness specimen of the wood plate, 12 types were manufactured by varying the combination of a main member (veneer and plywood) and reinforcement (glass fiber sheet and glass fiber cloth). The results of the fracture toughness test indicated that the 5% yield load of the specimen using plywood was 18% higher than that of the specimen using veneer, and that the specimen reinforced by inserting glass fiber sheets between testing materials (Type-3-PS) had the highest average 5% yield load 4841 N. Thus, a moment resistance strength test was performed by applying Type-3-PS to a column-beam joint. The results of the test indicated that compared to the specimen using a steel plate and a drift pin (Type-A), the maximum moment ratio of the specimen using a glass fiber reinforced wood plate (Type-3-PS) and a drift pin (Type-B) was 0.79; and that a rupture occurred in the wood plate due to high stiffness of the drift pin. The maximum moment ratio of the specimen using a glass fiber reinforced wood plate (Type-3-PS) and a glass fiber reinforced wooden laminated pin (Type-C) was 0.67, which showed low performance. However, unlike Type-A, a ductile fracture occurred on Type-C, and the load gradually decreased even after the maximum moment.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.1
• /
• pp.51-61
• /
• 1993

A systematic approach of the energy method is proposed for analysis of axisymmetric deep drawing in which the total deforming region is divided into five sections by the geometric characteristic. The corresponding solution is found through optimization of the total energy dissipation with respect to some parameters assumed in the kinematically admissible velocity field defined over each region. The sheet blank is divided into three-or five-layers to consider the bending effect. For the evaluation of frictional energy, it is assumed that the blank holding force acts on the outer rim of the flange and that the contact pressure acting on punch shoulder or die shoulder has uniform distributions, respectively. The computed results by the present method are compared with the experiment and the computed results by the elastic-plastic finite element method for the distribution of thickness strain and the relation between the punch stroke and punch load. The results for the case of multi-layers show better agreements than for the case of a single layer in load vs. stroke relation and strain distribution. It is thus shown that the multi-layer technique can be effectively employed in analyzing axisymmetric deep drawing in connection with the energy method.