• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.5
• /
• pp.789-798
• /
• 2020

This paper considers the development of the dynamic analysis model and simulation-based operation safety estimation of A-Frame to be applied to the test evaluation support vessel for real sea test. The support vessel will be manufactured by modifying the existing offshore support vessel. Also, development and installation of various sensors and supporting facilities for test evaluation are under preparation. Among these facilities, A-Frame is an equipment that transfers marine equipment from ship deck to the sea floor, and is being designed to transfer up to 50 ton class equipment. However, the A-Frame is a moving equipment using hydraulic cylinders. When the 50 ton equipment is attached and transferred to A-Frame, the buckling of cylinders may occur or A-Frame becomes inoperable due to the influence of huge inertia. For this reason, safety verification should be performed using dynamic analysis techniques that can take into account huge inertia forces in the design of A-Frame. Therefore, in this study, A-Frame and ship behavior were modeled using dynamic analysis method, and the applied loads of various equipment including hydraulic cylinder of A-Frame was measured and the operation safety review was performed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.10
• /
• pp.1852-1858
• /
• 2007

To Increase availability and to enhance the safety, the modernization of Instrumentation & Control (I&C) systems is considered. The extended use of the digital technology lets nuclear power plants(NPPs) to replace their old analog systems with some proven digital systems. To adapt digital equipment to plants effectively and systematically, however, there must be an essential prerequisite, which is to evaluate current I&C equipment. This paper shows a practical methodology to evaluate the current status and reliability of I&C systems of NPPs using Reliability Evaluation System(RES) before performing upgrades or replacements for systems. The proposed method was applied to KORI Unit 2. The proposed method shows the current status of operating I&C systems effectively for upgrading I&C systems.

• IE interfaces
• /
• v.12 no.1
• /
• pp.32-42
• /
• 1999

This paper proposes and implementation procedure for an automatic assembly system from a manual assembly and an evaluation method of implemented several automatic system alternatives using an AHP (Analytic Hierarchy Process) in a small-sized motor. First, the current product is redesigned for DFA (Design For Assembly) and assembly automation of motor, and then it is decided mechanisms of moving, magazining, feeding, composing of each part using main joining equipment and auxiliary equipment. Following the decided mechanism, the necessary assembly machines are selected or designed considering objectives and assembly conditions. Finally, the layout alternatives are completed for the automatic assembly system. According to the evaluation criteria which are established in advance, the automatic system alternatives are analyzed using AHP.

• Proceedings of the KSR Conference
• /
• 2000.05a
• /
• pp.157-163
• /
• 2000

Testing evaluation is a part of process for design, production, evaluation, operation and abolition, and is the process of certifying system performance. The main purpose of testing evaluation is to reduce the risk factor under the determining process. Testing process has the three step such as design qualification, integration and validation test in factory, system integration and commissioning test. Design Qualification is to verify errors on the design process. Integration and validation test in factory is for the H/W and S/W of an equipment and is to verify interface of subsystem, communication protocol and main functions. System integration and commissioning test is a functional test to adjust successful installation of equipment. According to the testing process, briefly consideration for test item, test method and test contents about signalling system is carried out.

• Transactions of the Korean hydrogen and new energy society
• /
• v.33 no.3
• /
• pp.232-239
• /
• 2022

This study performed qualitative and quantitative risk assessment of equipment for evaluating the protocol of hydrogen refueling stations and suggested measures to improve safety. Hazard and operability study was performed for qualitative risk assessment, and Hy-KoRAM was used for quantitative risk assessment. Through a qualitative risk assessment, additional ventilation devices were installed, simultaneous venting of the storage container was prohibited, and the number of repeated refilling of the evaluation equipment was identified to manage the number of fillings of the container. Through quantitative risk assessment, the area around the device was set as a restricted area when evaluating the station, and measures were suggested to reduce the frequency of accidents.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.24 no.3
• /
• pp.123-128
• /
• 2020

Analysis of the 2016 Gyeongju earthquake and the 2017 Pohang earthquake showed the characteristics of a typical high-frequency earthquake with many high-frequency components, short time strong motion duration, and large peak ground acceleration relative to the magnitude of the earthquake. Domestic nuclear power plants were designed and evaluated based on NRC's Regulatory Guide 1.60 design response spectrum, which had a great deal of energy in the low-frequency range. Therefore, nuclear power plants should carry out seismic verification and seismic performance evaluation of systems, structures, and components by reflecting the domestic characteristics of earthquakes. In this study, high-frequency amplification factors that can be used for seismic verification and seismic performance evaluation of nuclear power plant systems, structures, and equipment were analyzed. In order to analyze the high-frequency amplification factor, five sets of seismic time history were generated, which were matched with the uniform hazard response spectrum to reflect the characteristics of domestic earthquake motion. The nuclear power plant was subjected to seismic analysis for the construction of the Korean standard nuclear power plant, OPR1000, which is a reactor building, an auxiliary building assembly, a component cooling water heat exchanger building, and an essential service water building. Based on the results of the seismic analysis, a high-frequency amplification factor was derived upon the calculation of the floor response spectrum of the important locations of nuclear power plants. The high-frequency amplification factor can be effectively used for the seismic verification and seismic performance evaluation of electric equipment which are sensitive to high-frequency earthquakes.

• Korea Journal of Hospital Management
• /
• v.5 no.2
• /
• pp.22-39
• /
• 2000

The purpose of this study was to determine the difference between estimated profit and utilization of medical equipment upon purchasing and actual results at one teaching hospital in Seoul, Korea Medical equipments over $100,000 from 1992 to 1997 were selected and results were as follows: 1. Twenty equipments out of thirty exceeded estimated profits and the difference was 3.98 billion won and ten equipments did not reach the estimated profits and 5.5 billion won was the difference. Diagnostic equipment exceeded the estimated profit which surgical equipment didn't. 2. Eleven equipments exceeded estimated utilization, which showed 100%. In the mean time, eighteen equipments didn't reach the estimated utilization, which was 71%. Diagnostic equipment showed the less estimated utilization than surgical equipment 3. Twenty-one equipments showed the 6.83 billion won profits and nine equipments showed the 1.6 billion won deficits. Diagnostic equipment was more profitable than surgical equipment. Finally. diagnostic equipment helped improving hospital management than surgical equipment. 4. Main factors which showed the big difference from the initial plan were lacking reasonable estimated method, no evaluation system for purchase, emphasis in medical treatment, excessive expenditure in maintenance, duplicated investment for medical equipment and leadership commitment. As a result. Substantial planning is required from the requesting department in consideration of estimated profit and utilization and systematic quality control is needed to confirm. Also, One-sided decision making should be avoided to purchase a high cost medical equipment and efforts should be made in examining carefully and developing a reasonable analytic method.

• The Journal of the Korea Contents Association
• /
• v.19 no.8
• /
• pp.79-92
• /
• 2019

The existing computer equipment management system is designed to computerize and manage equipment information that was managed only by documents in the computer room. However, the existing system focuses on computerizing the equipment arranged in the document, so there is a limit to the equipment that can be registered and it is difficult to find the necessary equipment. In addition, it caused inconvenience to confirm whether the registered equipment is currently used. In this paper, we redesign and implement the computer equipment management system to solve the problem. For this purpose, the existing computer equipment management system was thoroughly analyzed throughout, and the system is designed and implemented to improve the system by reflecting the opinions of public officials and management companies using the system. In the performance evaluation, the efficiency of the improved system is proved by comparing the number of equipment registrations and equipment search accuracy of the existing system.

• Journal of the Ergonomics Society of Korea
• /
• v.30 no.4
• /
• pp.451-458
• /
• 2011

Objective: This study is to develop a design and evaluation guide to the ergonomic design of the farm working convenient equipments in order for the elderly to use them easily and safely. Background: The aging population has already increased in farm villages. But due to the usage of the farm working equipments that did not reflect the characteristics and functional changes of aging, accidents and patients with disease are increasing. Method: The study investigated the functional changes and physical, cognitive, and sensuous characteristics of the aged. By determining the criteria for classification of the convenient equipments by crop, and by finding out the items necessary for the ergonomic design, a guide to this study is proposed. Results: It is obvious that the physical, cognitive and sensuous functions change as the aging process continues. Therefore, for the design and evaluation of Control Panel, Control Lever, Frame Size, Shape, and Equipment Weight that are the necessary items for the ergonomic approach for the farm working equipments, such characteristics have to be reflected. Conclusion: Through this study, a guide to the design and evaluation of convenient equipments for the farm works that reflected the aging characteristics and functional changes has been proposed. Application: The result of this study is to expect not only designers but also related specialists to make the best use of it.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.2
• /
• pp.27-32
• /
• 2010

This paper suggests the new performance evaluation system which is suitable for high speed EFEM(Equipment Front End Module) device using a semiconductor process. An EFEM consisting of multi-joint robots is the mainstay of semiconductor automation, shuffling silicon wafers or quartz photo-masks between ultra-clean storage carriers and a variety of processing, measurement and testing systems. The theoretical and experimental studies for the development of performance evaluation system have been carried out. The presented results from the above investigation show considerably developed performance evaluation system for the high speed EFEM Especially, it is efficient for prepareing the WTO/TBT(Technical Barriers to Trade) Agreement and the PL(Product Liability) law.