• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10b
• /
• pp.530-533
• /
• 1993

This paper describes a new method of dynamic error compensation, using a digital convolution integrator and two digital low pass filters. In this method, the process of compensation consists of three steps. First, sampling and digitizing of input signal, second, removing the noise in sampled data by the low pass filter and third, making a convolution integral using the output data of low pass filters. This method showed a good experimental result of reducing dynamic error even if there was a slight noise in the input signal. As a result, the detecting time constant of resistance thermo-bulb was improved to about 1/10th.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.160-163
• /
• 2005

This paper proposes a simple MPPT control scheme of a Current-Control-Loop Error system Based that can be obtains a lot of advantage to compare with another digital control method, P&O and IncCond algorithm, that is applied mostly a PV system. An existent method is needed an expensive processor such as DSP that calculated to change the measure power of a using current and voltage sensor at the once. Therefore, it is applied a small home power generation system that required many expenses. But, a proposed method is easy to solve the cost reduction and power unbalance problems that it is used by control scheme to limit error of a current control of common sensor. This proposed algorithm had verified through a simulation and an experiment on battery charger using PIC that is the microprocessor of a low price.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.4 no.3
• /
• pp.189-196
• /
• 2011

In this paper, we analyze the error performance of SIC-based signal detection methods in MIMO systems. Considered detection methods are SIC signal detection and LR-SIC signal detection. We derive BLER performance of the methods and the performance is confirmed by computer simulations.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.1
• /
• pp.46-54
• /
• 2002

Plasma Display Panel (PDP) is required to be both the determination of white point of each gray level and the inverse gamma correction since no-balanced RGB cell and linear property of PDP, respectively. However, these two methods cause degradation of grey level representation and undesirable false contour in the dark areas on PDP. In this paper, we implemented real time image processor of the proposed error diffusion algorithm and unsharp masking operation to protect the blurring image caused by the error diffusion. Experimental results showed drastic improvements of gray level representation and reduction of undesirable false contour.

• Proceedings of the KIEE Conference
• /
• 2006.07d
• /
• pp.2142-2143
• /
• 2006

Today any data storage system cannot satisfy all of these conditions, however holographic data storage system can perform faster data transfer rate because it is a page oriented memory system using volume hologram in writing and retrieving data. System can be constructed without mechanically actuating part therefore fast data transfer rate and high storage capacity about 1Tb/cm3 can be realized. In this research, to reduce errors of binary data stored in holographic data storage system, a new method for bit error reduction is suggested. Firstly, find fuzzy rule to use test bed system for Element of Holographic Digital Data System. Secondly, make fuzzy rule table using DNA coding method. Finally, reduce prior error element and recording digital data. Recording ratio and reconstruction ratio show good performance.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.830-835
• /
• 1993

The errors in machining process by CNC machining center are due to many elements, such as the delay of the servo drivers, friction and the gain mismatch between x-axis and y-axis motors and so on. We made a counter circuit to measure the output of motor encoders for the motion error analysis of a CNC machining center, and have measured the errors experimentally when the CNC performs a circular interpolation. We have also used an iterative learning method to reduce the radius errors and stick motion errors generated by the CNC machining center performing a circular interpolation. The proposed learning scheme worked well and the circle obtained has smaller error.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1784-1788
• /
• 2003

For the improvement of geometrical accuracy in end milling, cutting method and cutting condition selection are investigated in this paper. As machining processes are composed of several steps such as roughing, semi-finishing. and finishing, cutting forces and tool deflection are calculated considering surface shape generated by the previous cutting. The effects of tool teeth numbers, tool geometry, and cutting conditions on the form error are analyzed. Using the from error prediction method from tool deflection, cutting condition for geometrical accuracy improvement is discussed. The characteristics and the difference of generated surface shape in up and down milling are dealt with and over-cut free condition in up milling is presented. The form error reduction method by alternating up and down milling is also suggested. The effectiveness of the presented method is examined from a set of cutting tests under various cutting conditions. This research contributes to cutting process optimization for the geometrical accuracy improvement in die and mold manufacture.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.4
• /
• pp.1954-1971
• /
• 2017

In this work, first, a multiuser detection (MUD) algorithm based on component-level soft interference cancellation and linear minimum mean square error (CLSIC-LMMSE) is proposed, which can enhance the bit error ratio (BER) performance of the traditional SIC-LMMSE-based MUD by mitigating error propagation. Second, for non-binary low density parity check (NB-LDPC) coded high-order modulation systems, when the proposed algorithm is integrated with partial mapping, the receiver with iterative detection and decoding (IDD) achieves not only better BER performance but also significantly computational complexity reduction over the traditional SIC-LMMSE-based IDD scheme. Extrinsic information transfer chart (EXIT) analysis and numerical simulations are both used to support the conclusions.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1986.10a
• /
• pp.56-58
• /
• 1986

This paper propose a conversion method to reduce prediction error produced when PRA(Pel Recursive Algorithm) motion estimation method is used in real image. The method is th get a spatial difference image from a given raw image and then to apply any PRA method to the difference image. The algorithm proposed in this paper is compared with several algorithm including the ubiquitious Netravali and Robbins` based on the performance and the hardware complexity. Computer simulation shows that the difference image conversion method is about 4.5dB better than the other algorithm with regard to prediction error power.

• Journal of the Korean Data and Information Science Society
• /
• v.26 no.3
• /
• pp.749-754
• /
• 2015

This article presents Bayesian approach to regression splines with knots on a grid of equally spaced sample quantiles of the independent variables under functional measurement error model.We consider small area model by using penalized splines of non-linear pattern. Specifically, in a basis functions of the regression spline, we use radial basis functions. To fit the model and estimate parameters we suggest a hierarchical Bayesian framework using Markov Chain Monte Carlo methodology. Furthermore, we illustrate the method in an application data. We check the convergence by a potential scale reduction factor and we use the posterior predictive p-value and the mean logarithmic conditional predictive ordinate to compar models.