• KEPCO Journal on Electric Power and Energy
• /
• 제6권4호
• /
• pp.473-480
• /
• 2020

In this paper, we proposed a high frequency equivalent circuit considering parasitic impedance components for differential noise analysis on the input stage during DC-DC buck converter switching operation. Based on the proposed equivalent circuit model, we presented a method to measure parasitic impedance parameters included in DC bus plate, IGBT, and PCB track using the gain phase method of a network analyzer. In order to verify the validity of this model, a DC-DC prototype consisting of a buck converter, a signal analyzer, and a LISN device, and then resonance frequency was measured in the frequency range between 150 kHz and 30 MHz. The validity of the parasitic impedance measurement method and the proposed equivalent model is verified by deriving that the measured resonance frequency and the resonance frequency of the proposed high frequency equivalent model are the same.

• 한국전기전자재료학회논문지
• /
• 제19권12호
• /
• pp.1099-1105
• /
• 2006

In this paper, the equivalent circuit model of a Rosen-type multilayer piezoelectric transformer(MPT) has been proposed based on the Mason's equivalent circuit model and the principle of single layer piezoelectric plate. From the piezoelectric direct and converse effects, the symbolic expressions between the electric inputs and outputs of the MPT have been derived from the equivalent circuit model. A simplified equivalent circuit model of the MPT whose driving part has a single input form has been proposed. The symbolic expressions of the driving part have been derived from the simplified equivalent circuit model and the model was compared with the multi-input equivalent circuit model through the simulation. In the comparisons between the simulation results and the experimental data, output voltage is 630 Vp-p in case of 11-layered MPT and 670 Vp-p for 13-layered MPT over the experiment range. As the load resistance increases, output voltage increases and saturates over $300k{\Omega}$ and the resonant frequency changes from 102 kHz to 103 kHz. The simulation and the experimental results agree well over different load resistances and frequencies.

• 한국철도학회논문집
• /
• 제11권5호
• /
• pp.465-470
• /
• 2008

본 논문에서는 철도 차량용 허니콤 판재를 대상으로 음투과 손실을 검토한다. 허니콤재의 음투과 손실을 예측하는 데에는 등가 직방성 평판 모델과 등가 질량법칙을 적용한다. 음투과 손실의 예측치를 측정치와 비교하여 예측 모델의 신뢰도와 한계를 검토한다. 또한 일치효과와 국부공진 효과가 차음성능에 미치는 효과를 검토한다. 본 연구는 국부공진 주파수대역을 적절히 적용한다면, 등가 직방성 평판 모델을 허니콤재의 음투과손실 예측모델로 사용 할 수 있음을 보인다. 최종적으로, 국부 공진에 의한 차응성능의 급격한 저하에 대한 대책을 제시하고 그 차음 성능에 대한 효과를 분석한다.

• Composites Research
• /
• 제33권6호
• /
• pp.377-382
• /
• 2020

본 연구에서는 Rayleigh-Ritz 법을 이용하여 열린 단면보로 보강된 복합재료 주름판의 자유진동 특성을 연구하였다. 복합재료 주름판에 대해 등가균질모델을 이용하였으며, 이 등가모델은 주름판을 두 수직방향에 대해 서로 다른 재료특성을 갖도록 직교이방성판으로 취급한다. 등가 직교이방성판의 운동은 회전 관성 및 횡전단변형을 고려하기 위해 1차 전단변형이론을 기초로 표현된다. 또한 진동형상에서 보강재의 위치에 따른 국부 형상을 표현하기 위해 이산보강이론이 적용되었다. 제안된 해석 방법에 대한 타당성을 검증하기 위해 ANSYS를 이용한 유한요소해석을 수행하였으며, 두 방법을 이용해 얻은 진동수 및 진동형상을 비교하였다.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.408-413
• /
• 2004

High speed planning boats also have been required more and more the rational strength analysis and evaluation for the optimal structural design in respect of the structural lightness according to the high speed trend. Even though the suggestion of the simple type equation for the equivalent dynamic pressure is reasonable to design the scantling of ship structure conveniently, many research activities for more reasonable improvement of the simple design pressure, have been continued to suggest the more accurate equivalent static description of tire structural response such as the deflection and stress of hull structure. In this research, we focus on the aluminum bottom stiffened plate structure in which structural scantling is mainly depend on the local loads such as dynamic or impact pressure without other load effects and structural response for the simple dynamic equivalent pressure was investigated through the structural analysis. In order to investigate the structural response of the bottom stiffened plate structure subjected to the dynamic equivalent design pressure, linear and nonlinear structural analysis of the bottom stiffened plate structure of 4.3 ton aluminum planning boat was performed based on the equivalent static applied loads which were derived from the KR regulation and representative one among various dynamic equivalent pressure equations. From above analysis results, we found that the response such as deflection and stress of plate member was similar with the response results of one plate member model with fixed boundary, which was published previous paper and in case of KR design loading, all response of stiffened plate structure were within elastic limit. Through the nonlinear analysis, nearly elastic behavior including the slight geometrical nonlinear response was dominant but plastic local zone was appeared at $85\%$ limit load. Therefore, we can say that through tire linear and nonlinear analysis, this stiffened plate member has no structural strength problem based on the yield criteria in case within $60\%$ limit load except the other strength point of view such as the fatigue and buckling problem.

• Nuclear Engineering and Technology
• /
• 제47권4호
• /
• pp.500-511
• /
• 2015

In this study, the natural frequencies of the perforated square plate with a square penetration pattern are obtained as a function of ligament efficiency using the commercial finite-element analysis code ANSYS. In addition, they are used to extract the effective modulus of elasticity under an assumption of a constant Poisson's ratio. The effective modulus of elasticity of the fully perforated square plate is applied to the modal analysis of a partially perforated square plate using a homogeneous finite-element analysis model. The natural frequencies and the corresponding mode shapes of the homogeneous model are compared with the results of the detailed finite-element analysis model of the partially perforated square plate to check the validity of the effective modulus of elasticity. In addition, the theoretical method to calculate the natural frequencies of a partially perforated square plate with fixed edges is suggested according to the Rayleigh-Ritz method.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2005년도 종합학술발표회 논문집 Vol.15 No.1
• /
• pp.17-22
• /
• 2005

This paper presents a improvement equivalent circuit model for Miniaturized LTCC bandpass filter with two transmission zeros using feed-back capacitor. The bandpass filter equivalent circuit is evaluated by parallel network analysis. Besides, the filter is modeled by proposed passive element modeling algorithm in previous work. Compared to the equivalent circuit of established paper that is configured by excepted capacitance between ground plate and signal plate, this model can include that. The result, the LTCC bandpass filter reduce layers and the size is more smaller.

• 한국철도학회논문집
• /
• 제13권4호
• /
• pp.404-411
• /
• 2010

철도차량용 선형유도전동기(Linear Induction Motor, LIM) 축소-회전형 모델의 기본 설계 결과를 검증하기 위하여 LIM의 자기등가회로법을 이용한 파라미터 도출 및 특성 계산을 수행하였다. LIM의 경우, 자기등가회로상의 파라미터는 LIM의 전기자 코어와 2차측 알루미늄 도체판의 형상 및 공극에 대한 함수로써 표현이 가능하다. 즉 전기자 코어와 2차측 알루미늄 도체판의 형상 및 공극 변경에 의해 LIM의 특성이 크게 달라질 수 있다는 것을 의미한다. 따라서 본 연구에서는 철도차량용 LIM 축소-회전형 모델의 공극, 2차측 AL-Plate의 두께, 오버행 길이, 형상 변경에 따른 LIM 축소-회전형 모델의 자기등가회로 파라미터 및 특성의 변화 추세를 분석하여, 철도차량용 실모델 LIM 개발을 위한 기초 연구를 수행하였다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제7권5호
• /
• pp.805-816
• /
• 2015

In the present study, external restraints imposed normal to the plate during the cooling stage were determined to be effective for reduction of the angular distortion of butt-welded or fillet-welded plate. A welding analysis model under external force during the cooling stage was idealized as a prismatic member subjected to pure bending. The external restraint was represented by vertical force on both sides of the work piece and bending stress forms in the transverse direction. The additional bending stress distribution across the plate thickness was reflected in the improved inherent strain model, and a set of inherent strain charts with different levels of bending stress were newly calculated. From an elastic linear FE analysis using the inherent strain values taken from the chart and comparing them with those from a 3D thermal elasto-plastic FE analysis, welding deformation can be calculated.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 추계학술대회논문집; 한국과학기술회관; 6 Nov. 1997
• /
• pp.402-407
• /
• 1997

For cylindrical shells, the closed-form solutions are limited only to the cases with special boundary and/or loading conditions. Though the finite element method is certainly a powerful solution approach for the general structural dynamics problems, it is known to provide reliable solutions only in the low frequency region due to the inherent high sensitivities of structural and numerical modeling errors. Instead, the spectral element method has been proved to provide extremely accurate dynamic responses even in the high frequency region. Since the wave characteristics of a cylindrical shell becomes identical to that of a flat plate as the frequency increases, an equivalent plate model (EPM) representing the high-frequency dynamic characteristics of a cylindrical shell is introduced herein. The EPM-based spectral element analysis solutions are compared with the known analytical solutions for the corresponding cylindrical shell to confirm the validity of the present modeling approach.