• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.1
• /
• pp.132-142
• /
• 2000

The objective of this study is to experimentally investigate the noise propagating characteristics, the noise reduction mechanism and the performance of a slotted tube attached at the exit plane of a circular convergent nozzle. The experiment is performed through the systematic change of the jet pressure ratio and the slot length under the condition of two kinds of open area ratios, 25% and 51%. The open area ratio calculated by the tube length equivalent for the slot length is defined as the ratio of the total slot area to the surface area of a slotted tube. The experimental results for the near and far field sound, the visualization of jet structures and the static pressure distributions in the jet passing through a slotted tube are presented and explained in comparison with those for a simple tube. The propagating characteristics of supersonic jet noises from the slotted tube is closely connected with the slot length rather than the open area ratio, and its propagating pattern is similar to the simple tube. It is shown that the slotted tube has a good performance to suppress the shock-associated noise as well as the turbulent mixing noise in the range of a limited jet pressure and slot dimension. The considerable suppression of the shock‘associated noise is mainly due to the pressure relief caused by the high-speed jets passing through the slots on the tube. Both the strength of shock waves and the interval between them in a jet plume are decreased by the pressure relief. Moreover, the pressure relief is divided into the gradual and the sudden relief depending upon the open area ratio of the slotted tube. Consequently, the shock waves in a jet plume are also changed by the type of pressure relief. The gradual pressure relief caused by the slotted tube with the open area ratio 25% generates the weak oblique shock waves. On the contrary, the weak normal shock waves appear due to the sudden pressure relief caused by the slotted tube with the open area ratio 51%.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.1
• /
• pp.1-10
• /
• 2004

This paper presents a navigation garde capacitive microaccelerometer, whose low-noise high-resolution detection capability is achieved by a new electrode design based on a high-amplitude anti-phase sense voltage. We reduce the mechanical noise of the microaccelerometer to the level of 5.5$\mu\textrm{g}$/(equation omitted) by increasing the proof-mass based on deep RIE process of an SOI wafer. We reduce the electrical noise as low as 0.6$\mu\textrm{g}$/(equation omitted) by using an anti-phase high-amplitude square-wave sense voltage of 19V. The nonlinearity problem caused by the high-amplitude sense voltage is solved by a new electrode design of branched finger type. Combined use of the branched finger electrode and high-amplitude sense voltage generates self force-balancing effects, resulting in an 140％ increase of the bandwidth from 726㎐ to 1,734㎐. For a fixed sense voltage of 10V, the total noise is measured as 2.6$\mu\textrm{g}$/(equation omitted) at the air pressure of 3.9torr, which is the 51％ of the total noise of 5.1$\mu\textrm{g}$/(equation omitted) at the atmospheric pressure. From the excitation test using 1g, 10㎐ sinusoidal acceleration, the signal-to-noise ratio of the fabricated microaccelerometer is measured as 105㏈, which is equivalent to the noise level of 5.7$\mu\textrm{g}$/(equation omitted). The sensitivity and linearity of the branched finger capacitive microaccelerometer are measured as 0.638V/g and 0.044％, respectively.

• Progress in Medical Physics
• /
• v.11 no.1
• /
• pp.19-27
• /
• 2000

In order to predict the propagation of road traffic noise over level terrain, this paper presents the model of the simple monopole and dipole source. Excess attenuations by ground acoustic impedance with continuity are investigated by outdoor experiments. In this results, the propagation of road traffic noise is affected by the acoustic impedance properties of the ground surface over which the noise travels, particularly when the receiver position is close to the surface. These results are then used to derive sound pressure level contours for the attenuation with distance of the equivalent energy level received from passing vehicle. The percentage of deep sleep and the number of wakings are studied for continuous traffic noise. The hearing loss and sensitivity threshold shift is investigated by changing the various parameters such as the effects of aging and noise exposure. Evaluation of the response of human to traffic noise is discribed. It is shown that exposure to excessive noise can cause temporary loss of hearing that may become permanent if the exposure is prolonged or intense.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.2
• /
• pp.126-134
• /
• 2007

Although there has been substantial research on the squeal noise for the automotive brake system, robust design issues with respect to control factors equivalent to design variables in optimization, noise factors due to system uncertainties, and signal factors designed to accommodate a user-adjustable setting still need to be addressed. For the purpose, the robust design applied to the disk brake system has been investigated by DOE (Design of Experiments) based Taguchi analysis with dynamic characteristics. The specific goal of this methodology is to identify a design with linear signal-response relationship, and variability minimization. The finite element models of the disk brake assembly have been constructed, and the squeal noise problems have been solved by complex eigenvalue analysis. As the practical robust design to reduce the brake squeal noise, material properties of pad, disk, and backplate, thickness and geometry of pad are selected as control factors, material properties of pad and disk, and the contact stiffness have been considered as noise factors, and friction coefficient between pad and disk is chosen as a signal factor. Through the DOE based robust design, the signal-to-noise ratio and the sensitivity for each orthogonal array experiment have been analyzed. Also, it has been proved that the proposed robust design is effective and adequate to reduce the brake squeal noise.

• Journal of Biosystems Engineering
• /
• v.32 no.3
• /
• pp.153-159
• /
• 2007

This study was conducted to measure and analyze the noise from a combine head. The combine head, comprised of a cutting knife assembly, pick-up chains, horizontally conveying chains and vertically conveying chains, had an overall sound level of 101 dBA. The sound levels of each component were, respectively, 98.3 dBA for the cutting knife assembly, 88.9 dBA for the pick-up chains, 79.8 dBA for the horizontally conveying chains and 86.3 dBA for the vertically conveying chains, being equivalent to 54.4%, 18.4%, 6.5% and 13.7% of the overall head noise. The main cause of the head noise was considered the impacts that the joint of the cutting knife assembly made with frame when it oscillated. The impact sound was also generated when the chain lug collided with the chain case. To reduce these impact sound, anti-vibration rubbers were installed on the knife assembly joint and the chain cases. It reduced the head noise by 4 dBA but the overall noise level of the combine head was still high. In order to protect the combine operators more effectively from the noise, a safety cab needs to be installed on the combine.

• Journal of IKEEE
• /
• v.3 no.2 s.5
• /
• pp.226-235
• /
• 1999

To investigate SPICE noise model and the behavior of its parameters, 1/f noise of NMOS devices fabricated by BiCMOS process is measured and compared to the various noise models and measured results. For the long channel devices, bias dependence of the drain current noise power spectral density $S_{Id}$ of NMOS is similar to the previous results. Equivalent gate noise power spectral density $S_{Vg}$ shows weak dependence on the gate and drain voltages in long channel NMOS as the previous results. However, it is shown that most of published noise models are difficult to apply to short channel devices. Therefore, in this study, with comparison of our experimental results, we have tried to find the model of 1/f noise, appropriate for our NMOS device fabricated by BiCMOS process.

• Journal of Internet Computing and Services
• /
• v.17 no.1
• /
• pp.1-6
• /
• 2016

The biased zero-error probability and its related algorithms require heavy computational burden related with some summation operations at each iteration time. In this paper, a recursive approach to the biased zero-error probability and related algorithms are proposed, and compared in the simulation environment of shallow water communication channels with ambient noise of biased Gaussian and impulsive noise. The proposed recursive method has significantly reduced computational burden regardless of sample size, contrast to the original MBZEP algorithm with computational complexity proportional to sample size. With this computational efficiency the proposed algorithm, compared with the block-processing method, shows the equivalent robustness to multipath fading, biased Gaussian and impulsive noise.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.5
• /
• pp.863-871
• /
• 2003

In this paper, we design a high stable Ku-band phase-locked dielectric resonant microwave oscillator with the gate voltage controls of p-HEMT. By adapting the nonlinear equivalent elements which affects phase noise of microwave oscillator, we optimize the nonlinear elements of p-HEMT to have low phase noise operation. Using the scattering parameters according to bias voltages, we designed the gate voltage control microwave dielectric resonant oscillator and phase-locked loop circuits is applied to have the high stable operations. Designed microwave oscillator as a local oscillator of digital microwave communication shows that output power is 9.17dBm at 10.75GHz and it's phase noise is -88dBc/Hz at 10KHz offset frequency.

• Journal of IKEEE
• /
• v.3 no.2 s.5
• /
• pp.236-242
• /
• 1999

J noise component due to base spreading resistance ${\gamma}_{bb}$ of bipolar junction transistors fabricated by BiCMOS process is experimentally analyzed. The analysis of equivalent noise circuit for common collector shows that output 1/f noise value is purely generated from ${\gamma}_{bb}\;when\;g_m^{-1}-{\gamma}_{bb}-R_B$ is closely to zero. From the $S^{1/f}_{Irbb}=K_fI_b{^{A_1}}/f$, we fine that $A_f=2,\;K_f{\simeq}5{\times}10^{-9}$. And Hooge constant ${\alpha}$ values are in the order, of 10$^{-3}$.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.818-821
• /
• 2005

The sound measurement procedures of IEC 61400-11 are applied to field test and evaluation of noise emission from 1.5 MW wind turbine generator (WTG) at Yongdang and 660 kW WTG at Hangwon in Jeju Island. Apparent sound power level, wind speed dependence and third-octave band levels are evaluated for both of WTGs. 1.5 MW WTG at Yongdang is found to emit lower sound power than 660 kW one at Hangwon, which seems to be due to lower rotating speed of the rotor of WTG at Yongdang. Equivalent continuous sound pressure levels (ECSPL) of 660 kW WTG at Hangwon vary more widely with wind speed than those of 1.5 MW WTG at Yongdang. The reason for this is believed to be the fixed blade rotating speed of WTG at Yongdang. One-third octave band analysis of the measured data show that the band components around 400-500 Hz are dominant for 1.5 MW WTG at Yongdang and those around 1K Hz are dominant for 660 kW WTG at Hangwon.