• Journal of the Semiconductor & Display Technology
• /
• v.16 no.1
• /
• pp.16-21
• /
• 2017

In this paper, the effect of battery-package shape of electric vehicle on the forced convection around a group of battery cells has been numerically investigated. Simulations for the two package shapes with straight/curved ducts have been conducted to examine the two design factors; the maximum temperature and the temperature deviation of a group of cells which influence the cell durability. The simulation of the conjugate heat transfer has been simplified by employing an equivalent thermal conductivity of cell that consists of various materials. It has been found that the maximum temperature and the temperature deviation of curved duct were lower than those of straight duct. Velocity fields have also been examined to describe the temperature distribution of a group of cells and the position of maximum temperature was found to be related to the dead zone of flow field.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.580-585
• /
• 2019

Batteries are being used in ESS, electric vehicles and uninterruptible power backup systems. Lead-acid batteries are the most used batteries for high capacity power back up equipment due to their high reliability and low price advantages. It is very important to estimate the chargeable capacity(SoH), and many algorithms were proposed to estimate the internal resistance of the battery. In this paper, the Battery Monitoring System(BMS) for high capacity uninterruptible power supply for IDC is proposed. A simple algorithm for estimating internal resistance was proposed. An computational block diagram of the proposed signal processing algorithm and BMS system configuration of CPU and analog circuit were shown. The proposed method was proved useful by presenting data examples of application to actual IDC sites.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.2
• /
• pp.263-269
• /
• 2012

In order to present that the electromagnetic compatibility standards following the frequency goes up which is based automotive electronics, in this paper, a hybrid/electric vehicle battery which reflects the frequency of the equivalent circuit model is introduced. By using this circuit modeling, the impedance characteristics can be analysed and an analyze of battery one cell is finished. Using this model, each different from the discharging situation, the discharge characteristic curve could be led. Basic theoretical approaches and measuring results through MATLAB and experimental validation of the EIS measurement equipment was used.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.955-956
• /
• 2011

본 연구의 목적은 전기 자동차 BDU(Battery Disconnected Unit)의 방열 설계를 위해 전기 및 열 등가회로를 설계하여 온도 특성을 파악하는 것이다. 이 온도 특성을 분석하기 위해서 해석 프로그램으로 매트랩(matlab)의 시뮬링크(simulink) 프로그램을 사용하였으며, 각 소자에서의 발열과 최대 온도 그리고 평균 온도의 해석 값을 통해 실험결과 데이터와 접목 시킨다면, 배터리 팩(battery pack)의 핵심 부품인 BDU의 최적 방열 설계를 이룰 수 있을 것으로 판단된다.

• Journal of Power Electronics
• /
• v.18 no.5
• /
• pp.1585-1594
• /
• 2018

The estimation of $LiFePO_4$/graphite battery states suffers from the prominent hysteresis phenomenon between the respective open-circuit voltage curves towards charging and discharging. A lot of hysteresis models have been documented to investigate the hysteresis mechanism. This paper reviews and deeply interprets four non-electrochemical hysteresis models and some improvements. These models can be conveniently incorporated into commonly used equivalent circuit models to reproduce battery behaviors. Through simulation and experimental comparisons of voltage predictions and state-of-charge estimations, the pros and cons of these models are presented.

• Proceedings of the KIEE Conference
• /
• 2000.11d
• /
• pp.669-671
• /
• 2000

Vehicle electric power system, which consists of two major components; an alternator and a battery, supplies electric power to vehicle electric and electronic systems. In recent years, bigger power supply is required for the rapid demand of the number of vehicle electric and electronic systems. It is important that vehicle power system should be analyzed exactly. For the simulation of vehicle electric power system, appropriate component model of vehicle electric power system should be chosen. In this paper, a simplified and accurate battery model is developed to obtain the battery parameters, and a Variable Alternator Terminal Voltage Model is introduced to described an alternator. The case study shows that simulation results using the suggested models are well agreed with the experiments.

• Proceedings of the KIEE Conference
• /
• 1999.11c
• /
• pp.570-572
• /
• 1999

An equivalent circuit model of vehicle charging-discharging system for simulation is developed. The vehicle electric power system consists of alternator and battery. The alternator must have adequate capacity for providing electric energy to all loads, and the battery supports the alternator by offering insufficient energy when the alternator output energy is not enough. The alternator model is simplified for the use of characteristic curve, which was provided by its manufacturer, and the battery model is separated in charging mode and discharging mode because of its complex characteristics. Developed circuit model is validated by comparing the simulation data and real experimental data.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.6
• /
• pp.549-556
• /
• 2014

This study proposes a parallel operation strategy for small wind turbine systems. A small wind turbine system consists of blade, permanent magnet synchronous generator, three-phase diode rectifier, DC/DC buck converter, and the battery load. This configuration has reliability, simple control algorithm, high efficiency, and low cost. In spite of these advantages, the system stops when unexpected failures occur. Possible failures can be divided into mechanical and electrical parts. The proposed strategy focuses on the failure of electrical parts, which is verified by numerical analysis through equivalent circuit and acquired general formula of small wind power generation systems. Simulation and experimental results prove its efficiency and usefulness.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.4
• /
• pp.251-260
• /
• 2020

A growing interest has emerged in recycling used automobile batteries into energy storage systems (ESSs) to prevent their harmful effects to the environment from improper disposal and to recycle such resources. To transform used batteries into ESSs, composing battery modules with similar performance by grading them is crucial. Imbalance among battery modules degrades the performance of an entire system. Thus, the selection of modules with similar performance and remaining life is the first prerequisite in the reuse of used batteries. In this study, we develop an instrument to measure the impedance spectrum of a battery module to predict the useful remaining life of the used battery. The developed hardware and software are used to apply the AC perturbation to the used battery module and measure its impedance spectrum. The developed instrument can measure the impedance spectrum of the battery module from 0.1 Hz to 1 kHz and calculate the equivalent circuit parameters through curve fitting. The performance of the developed instrument is verified by comparing the measured impedance spectra with those obtained by a commercial equipment.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.597-598
• /
• 2005

Recently, the performance of portable electric equipment can often improved by a Li-ion battery assisted by a supercapacitor. A supercapacitor can provide high power density as well as a low resistance in the hybrid system. In this study, we have prepared, as the pluse power souce, a commercially supplied Li-ion battery with a capacity of 700mAh and AC resistivity of $60m\Omega$ at 1kHz and nonaqeous asymmetric hybrid capacitor composed of an activated carbon cathode and MCMB anode, and have examined the electrochemical characteristics of hybrid capacitor and the pulse performances of parallel connected battery/hybrid capacitor source. The nonaqueous asymmetric hybrid capacitor, the stacks of 10 pairs of the cathode, the porous separator and the anode electrode were housed in Al-laminated film cell. The hybrid capacitor, which was charged and discharged at a constant current at $0.25mA/cm^2$ between 3 and 4.3V, has exhibited the capacitance of 100F. And the equivalent series resistance was $32m\Omega$ at 1kHz. By combining a Li-ion battery and a hybrid capacitor, the pulse performance of battery can be improved 23% in run time under a pulse discharge of 7C-rate.