• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.2
• /
• pp.23-28
• /
• 2014

This study investigates fluid flow and thermal stress at automotive exhaust manifolds as model 1 and 2. The maximum displacements happen at joint part connected with 4 pipes and upper middle of both parts in cases of model 1 and 2 respectively. At inner surface of the part connected with engine, maximum equivalent stresses of 991.85 and 698.96 MPa are shown in cases of model 1 and 2 respectively. As maximum velocities at the outlet at model 1 are shown at 19.46 and 14.61 m/s in cases of model 1 and 2 respectively, model 1 has more pressure drop than model 2. As result, model 2 has less pressure drop than 1. Model 2 has less deformation and stress than model 1. Model 2 has also less pressure drop than model 1. Therefore model 2 has more strength durability than model 1. This study result is applied with the design of safe automotive manifold and it can be useful to improve the durability by predicting prevention against the deformation due to exhaust gas.

• Transactions of the Korean hydrogen and new energy society
• /
• v.21 no.2
• /
• pp.129-135
• /
• 2010

Homogeneous charge compression ignition (HCCI) engines have the potential to provide both diesel-like efficiency and very low emissions of nitrogen oxide (NOx) and particulate matter(PM). However, several technical issues still must be resolved before HCCI can see application. Among these, steep pressure-rise rate which leads to narrow operating range of HCCI engine continues to be a major issue. This work investigates the combination of two methods to mitigate the excessive pressure-rise rates at high power output, namely fuel stratification and Cooled exhaust-gas recirculation (Cooled EGR), after identifying the each effects to pressure-rise rate. When applying the fuel stratification to simulation, total fuelling width of 0.15 at BDC is set as a equivalent ratio difference based on the previous research. In order to simulate the effects of cooled EGR, $CO_2$ mole fraction in pre-mixture is changed ranging from 0 to 30%. DME which has a characteristic of two-stage ignition is used as a fuel.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.11
• /
• pp.1140-1147
• /
• 2009

Flow analyses have been performed to investigate the uniformity of propellant flow through the fuel and oxidizer manifolds of a full-scaled gas generator for a pump-fed liquid rocket engines. Injectors were simulated as porous medium layers having equivalent pressure drops. The uniformity of propellants has been analyzed for 3 fuel rings and 3 injector head configurations. The mixture ratio distribution at the exit of injectors has been estimated from the mass flow rates of fuel and oxidizer. The best configuration of fuel ring and injection head was selected through these flow analyses.

• Journal of Mechanical Science and Technology
• /
• v.18 no.7
• /
• pp.1187-1195
• /
• 2004

The objective of this study is to investigate the effects of fuel temperature on the spray characteristics of a dual-orifice type swirl injector used in a gas turbine. The major parameters affecting spray characteristics are fuel temperature and injection pressure entering into the injector. In this study, the spray characteristics of a dual-orifice type swirl injector are investigated by varying fuel temperature from - 30$^{\circ}C$ to 120$^{\circ}C$ and injection pressure from 0.29 to 0.69 ㎫. Two kinds of fuel having different surface tension and viscosity are chosen as atomizing fluids. As a result, injection instability occurs in the low fuel temperature range due to icing phenomenon and fuel property change with a decrease of fuel temperature. As the injection pressure increases, the range of kinematic viscosity for stable atomization becomes wider. The properties controlling the SMD of spray is substantially different according to the fuel temperature range.

• Journal of Environmental Science International
• /
• v.21 no.1
• /
• pp.113-123
• /
• 2012

A unit emission reduction of nitrous oxide ($N_2O$) from anthropogenic sources is equivalent to a 310-unit $CO_2$ emission reduction because the $N_2O$ has the global warming potential (GWP) of 310. This greatly promoted very active development and commercialization of catalysts to control $N_2O$ emissions from large-scale stationary sources, representatively nitric acid production plants, and numerous catalytic systems have been proposed for the $N_2O$ reduction to date and here designated to Options A to C with respect to in-duct-application scenarios. Whether or not these Options are suitable for $N_2O$ emissions control in nitric acid industries is primarily determined by positions of them being operated in nitric acid plants, which is mainly due to the difference in gas temperatures, compositions and pressures. The Option A being installed in the $NH_3$ oxidation reactor requires catalysts that have very strong thermal stability and high selectivity, while the Option B technologies are operated between the $NO_2$ absorption column and the gas expander and catalysts with medium thermal stability, good water tolerance and strong hydrothermal stability are applicable for this option. Catalysts for the Option C, that is positioned after the gas expander thereby having the lowest gas temperatures and pressure, should possess high de$N_2O$ performance and excellent water tolerance under such conditions. Consequently, each de$N_2O$ technology has different opportunities in nitric acid production plants and the best solution needs to be chosen considering the process requirements.

• Journal of the Korean Society of Safety
• /
• v.31 no.3
• /
• pp.116-122
• /
• 2016

With the changes of industrial structure, contents and types in hazardous and dangerous works have been changed considerably. However, the hazardous and dangerous works by defined "Regulation for the hazardous and dangerous work employment restriction" and "Special education for safety and health"have not been amended over twenty years. This study aimed to identify the recent trends of the works by analyzing the death accidents cases from 2004 to 2013 and to present the management methods about future hazardous and dangerous works. The results showed that amount of 1,972 cases among 11,513 death accidents were equivalent to the works presented by "Regulation for the hazardous and dangerous work employment restriction". The amount of death accidents in 'Work of using construction equipment following construction machinery management act' was biggest among the death accidents cases and that of 'Work of handling pressure vessels following high-pressure gas safety control act' didn't show up. For the works in "Special education for safety and health"amount of 1,650 death accidents cases were equivalent. The amount of death accidents in 'Work involving a crane with a capacity of 1 ton or more or work which is carried out with a crane or hoist with a capacity of less than 1 ton in a workplace having at least 5 such machines' presented by "Special education for safety and health"was biggest. Also, death accidents case didn't occurred in three works presented by "Special education for safety and health". It was analyzed that works with low death accidents cases should be needed to study thoroughly the whole disaster research involving nonfatal accidents. Through this study, it was expected that regulation can be operated practically in the industrial field. Also, it is considered to increase

• Mass Spectrometry Letters
• /
• v.2 no.2
• /
• pp.41-44
• /
• 2011

Molecular compositions of two types of heavy oil were studied using positive atmospheric pressure photoionization (APPI) Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS). Vacuum gas oil (VGO) was generated from vacuum distillation of atmospheric residual oil (AR), and slurry oil (SLO) was generated from catalytic cracking of AR. These heavy oils have similar boiling point ranges in the range of 210-$650^{\circ}C$, but they showed different mass ranges and double-bond equivalent (DBE) distributions. Using DBE and carbon number distributions, aromatic ring distributions, and the extent of alkyl side chains were estimated. In addition to the main aromatic hydrocarbon compounds, those containing sulfur, nitrogen, and oxygen heteroatoms were identified using simple sample preparation and ultra-high mass resolution FT-ICR MS analysis. VGO is primarily composed of mono- and di-aromatic hydrocarbons as well as sulfur-containing hydrocarbons, whereas SLO contained mainly polyaromatic hydrocarbons and sulfur-containing hydrocarbons. Both heavy oils contain polyaromatic nitrogen components. SLO inludes shorter aromatic alkyl side chains than VGO. This study demonstrates that APPI FT-ICR MS is useful for molecular composition characterization of petroleum heavy oils obtained from different refining processes.

• Journal of the Korean institute of surface engineering
• /
• v.32 no.2
• /
• pp.165-171
• /
• 1999

The etching reaction of $UO_2$ in $CF_4/O_2$ gas plasma is examined as functions of $CF_4/O_2$ ratio, plasma power, and substrate temperature at up to $370^{\circ}C$ under the total pressure of 0.30 Torr. It is found that the highest etching rate is obtained at 20% $O_2$ mole fraction, regardless of r. f. power and substrate temperature. The existence of the optimum $CF_4/O_2$ ratio is confirmed by SEM, XPS and XRD analysis. The highest etching reaction rate at $370^{\circ}C$ under 150W exceeds 1000 monolayers/min., which is equivalent to 0.4$\mu\textrm{m}$/min. The mass spectrometry analysis results reveal that the major reaction product is uranium hexa-fluoride $UF_6$. Based on the experimental findings, dominant overall reaction of uranium dioxide in $CF_4/O_2$ plasma is determined : $8UO_2+12CF_4+3O_2=8UF_6+12CO_{2-x}$ where $CO_{2-x}$ represents the undetermined mix of $CO_2$ and CO.

• Nuclear Engineering and Technology
• /
• v.53 no.8
• /
• pp.2616-2628
• /
• 2021

The results of effective irradiation swelling in a wide range of burnup levels are numerically obtained for an inert matrix fuel, which are verified with DART model. The fission gas swelling of fuel particles is calculated with a mechanistic model, which depends on the external hydrostatic pressure. Additionally, irradiation and thermal creep effects are included in the inert matrix. The effects of matrix creep strains, external hydrostatic pressure and temperature on the effective irradiation swelling are investigated. The research results indicate that (1) the above effects are coupled with each other; (2) the matrix creep effects at high temperatures should be involved; and (3) ranged from 0 to 300 MPa, a remarkable dependence of external hydrostatic pressure can be found. Furthermore, an explicit multi-variable mathematic model is established for the effective irradiation swelling, as a function of particle volume fraction, temperature, external hydrostatic pressure and fuel particle fission density, which can well reproduce the finite element results. The mathematic model for the current volume fraction of fuel particles can help establish other effective performance models.

• Journal of the Korean Vacuum Society
• /
• v.8 no.3B
• /
• pp.368-375
• /
• 1999

The Maxwell equation and the transformer equivalent-circuit model are applied to a radio frequency planar inductively coupled plasma. The spatial distribution of the vector potential, the magnetic field, and the electric field are obtained analytically. As a result, the plasma current, the mutual inductance between the coil and the plasma, and the self inductance of plasma are found to increase with increasing skin depth. The spatial distribution of absorbed power has maximum where the antenna coil exists, and has a similar profile to that of the induced electric field. The power transfer efficiency is found to increase with increasing gas pressure before a saturation around p+ 20mTorr, while it shows an increase with the plasma density before a slight decrease around a density of $5\times10^{11}/\textrm{cm}^3$.