• Advanced Composite Materials
• /
• v.16 no.1
• /
• pp.1-10
• /
• 2007

Composite materials consisting of crushed carbon fiber reinforced plastics (CFRP) pieces and acrylonitrile-butadiene-styrene (ABS) resin were prepared by an injection mold method to solve the problem of recycling of CFRP. The electrical properties, such as electrical resistivity, alternating current impedance and electromagnetic interference (EMI) shielding effect, were measured for the composites. The electrical resistivity of the composites showed a percolation type of conduction behavior and no difference between parallel and perpendicular to the injection direction was observed for CFRP content higher than the critical value. Measurement of alternating current impedance revealed that the conduction mechanism is attributed to the direct conductive paths generated by distributed carbon fibers; however, strong frequency dependence of the impedance was observed for the CFRP content near the critical one. The frequency dependence of the impedance is caused by the inter-fiber connection and can be expressed as a simple equivalent circuit. The absorption component of shielding effect (SE) was smaller than the expected value estimated from its resistivity. The decline of SE is thought to be caused by the decrease in effective thickness due to fiber orientation.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.6
• /
• pp.81-89
• /
• 1996

Quantum RF impedance of SIS (superconductor insulator superconductor) junction has been analyzed by using through on tucker's quantum mixer theory in the frequency range form 80 GHz to 120 GHz. The embedding impedance of waveguide-type mixer mount and its equivalent circuit have been evaluated. From these evaluated results, the impedance matching efficiency between mixer mount embedding impedance and mixer port impedance of upper-side band and IF which were determined by augmented admittance matrix with given backshort position has been discussed in detail. It is found that the mixer with fixed backshort mount ahs a impedance matching efficiency about 80% at each port of mixer within 85GHz to 115GHz, which implys a conversion los of mixer would be good enough to be operated such a wide band frequency range. Therefore, the theoretical evaluated results show that our method can be used ot design the mixer mount without any mechanical tuning elements such a backshort or an E-plane tunners for wide band operation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.2
• /
• pp.107-115
• /
• 1997

In this paper, a 23 GHz push-push oscillator was designed and fabricated for 23 GHz point-to-point communication using split ring resonator. The split ring resonator was equivalent circuit and numerical method of MPIE(Mixed Potential Integral Equation). The analysis of split ring resonator which coupled between microstrip lines was carried out with transmission-mode using this results. The fabricated oscillator showed the output power of 4 dBm, the 1'st harmonic suppression of -20 dBc, the 3rd harmonic suppression of -34 dBc, a SSB phase noise of -109 dBc / Hz at 1MHz offset frequency from the carrier was achieved and 1.4 percents efficiency at 23 GHz. The experimental outputs were in good results with the theoretical and simulated results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.5
• /
• pp.541-546
• /
• 2008

A novel, simple and broadband $90^{\circ}$ phase shifter was proposed and fabricated by the LTCC process. It is composed of a $180^{\circ}$ transmission line between two $90^{\circ}$ shorted transmission lines. Design equations for the proposed $90^{\circ}$ phase shifter are derived by the method of admittance parameter analysis. Based on design equations, $90^{\circ}$ phase shifter was designed and fabricated to operate in the C-band with ${\pm}2^{\circ}$ of phase deviation.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.1
• /
• pp.143-147
• /
• 2005

In this paper, an axial type brushless DC motor which has double rotors using rare-earth magnet pieces is designed. This kind of motor has shorter axial length and is easier to assemble than the radial type motors. To get enough torque, NdFeB magnet is used and for the cost of production, the magnets are segmented to rectangle or disk shape. To design this motor, a equivalent circuit is adopted and the air-gap density is calculated using 3D finite element method to get exact parameters. The design variables are optimized with genetic algorithm. From the results of the simulations, the reference of the axial type BLDC motors can be obtained.

• Proceedings of the KIPE Conference
• /
• 2003.07b
• /
• pp.765-768
• /
• 2003

In the end of a production line a new built power converter has to undergo a series of stress tests. This can be achieved by connecting it to a dynamometer consisting of a three-phase machine joined by a rigid shaft to a DC load machine. The latter is controlled to create some specific load characteristic needed for the test. In this paper a test method is proposed, in which no mechanical equipment is needed. The suggested test stand consists only of a converter to be tested and a simulator converter. Both devices are connected back-to-back on the AC-side via smoothing reactors. The simulator operates in real-time as an equivalent load circuit, so that the device under test will only notice the behaviour of a three-phase machine under consideration of the load.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.14 no.6
• /
• pp.579-589
• /
• 1989

In this paper, planar power dividers/combiners for millimeter waves K-band or bands which can be printed on the substrates of hybrid or monolithic IC by surface mounting are designed and studied. Power dividers/combiners, and the conductor loss of microstrip lines in particualr the existing Wilkinson power dividers/combiners is modified ad amployes by ist equivalent circuit. Microwave CAD program SUPEROMPACT is employed for the Wilkinson power combiner which is modified and analyzed to reduce the high frequency coupling between the branches of the combiner, and the method to diminish the sensitivity of the input reflection of $2^n$-way power dividers/combiners is studied employing the commerical microwave CAD program package SUPERCOMPACT.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.8
• /
• pp.823-829
• /
• 2003

For high frequency microstrip line modelling, a fast inductance extraction technique using an adaptive PEEC(partial element equivalent circuit) grid is proposed. The grid refinement technique is based on the current distribution depend on the excitation frequencies and the geometry of the microstrip lines. The adaptive ids are refined mainly in the area where heavy currents reside. This technique is applied to the inductance extraction of the microstrip lines. The results show fast convergence, and this adaptive technique is efficient to reduce computing time and the number of grids.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.1984-1986
• /
• 1998

This paper presents an optimal efficiency control for the inverter fed induction machine system using neural network. The motor speed and the load torque vary the efficiency characteristics of an induction motor. The optimal slip frequency has nonlinearity varied by the load torque as well as the motor speed. The induction motor is driven using the inverter system and the indirect vector control method which input is slip frequency. The neural network for estimating the optimal slip frequency has two input layer(the motor speed and the load torque) and one output layer(the optimal slip frequency that minimize the input power). Learning algorithm of the neural network is the back-propagation. Using the equivalent circuit including the nonlinearity of the induction motor, the loss reduction is analyzed quantitatively. Experimental results are shown noticeable power savings by proposed scheme in high speed and light load conditions.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.1259-1260
• /
• 2006

High temperature superconducting(HTS) power cable is expected to be used for power transmission lines supplying electric power for densely populated cities in the near future. Commercializing of HTS power cable is coming. Simulation is required for safety before install of HTS power cable, a fabrication model used at the power system simulation. In this paper, we shows a single line-to ground fault analysis in the grid system which has a 100m length HTS power cable. The authors developed a single line-to-ground fault current calculation method which is considering the shield layer of HTS power cable. In the calculation, the T type equivalent circuit is used to derive the mutual inductance of the HTS power cable.