• Journal of Mechanical Science and Technology
• /
• v.18 no.4
• /
• pp.681-688
• /
• 2004

For use of the thermal cycle of the biochemical fluid sample, the isothermal temperature source with a large surface area was designed, fabricated and its thermal characterization was experimentally evaluated. The comprehensive overview of the technology trend on the temperature control devices was detailed. The large surface area isothermal temperature source was realized by using the vapor chamber heat spreader. The cost-effectiveness and simple manufacturing process were achieved by using the metal-etched wick structure. The temperature distribution was quantitatively investigated by using IR temperature imaging system at equivalent temperatures to the PCR thermal cycle. The standard deviation was measured to be within 0.7$^{\circ}C$ for each temperature cycle. This concludes that the presented isothermal temperature source enables no temperature gradient inside bio-sample fluid. Furthermore it can be applied to the cooling of the electronic devices due to its slimness and low thermal spreading resistance.

• Proceedings of the KIEE Conference
• /
• 2006.07a
• /
• pp.504-505
• /
• 2006

We installed the measurement equipment which measure the equivalent Salt Deposit Density(ESDD) of the domestic coast area in the selected 112 place and investigated the influence of the wind which blow at the point of 500m from coast installing a wind vane, wind gauge for realtime measurement. During september${\sim}$december, 2005, ESDD which passively measured at the point of 50m from coast is maximum C grade in the Homigot of Pohang, B grade in the Gochang and A grade in the remaining point. Also ESDD which is measured in the east coast, west coast respectively is the more the distance being far from the coast to inland, the more ESDD rapidly decreasing but each area of the south coast is difficult to identify the decreased tendency because of very low measurements.

• Solar Energy
• /
• v.2 no.2
• /
• pp.1-9
• /
• 1982

This paper presents a method. for estimating the useful output of solar heating sys-terns. Heating load calculations, climatic data and various conditions are used in this procedure to estimate the fraction of the monthly heating load supplied by solar energy for a particular system the design procedure presented in this paper referred to the f-chart method. The results of this study are as follows; 1) The collected energy is not rised lineary to collector area. 2) If the heating area has equivalent solar collector area, the solar energy utilization for space heating is over 90%. 3) Transmittance- absorptance product for radiation at normal incidence, (${\tau}{\alpha}$)/(${\tau}{\alpha}$)n, during most of the heating season is 0.92 for a two-cover collector. 4) Orientation of the collector has little effect on the annual performance of solar heating system within the $15^{\circ}$.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.453-458
• /
• 2001

The stability of turbulent nonpremixed interacting flames is investigated in terms of nozzle configuration shapes which depend on the existence of the center nozzles. Six nozzle arrangements which are cross 4, 5, 8, 9, square 8 and circular 8 nozzles are used for the experiment. Those are arranged to see the effect of the center nozzle out of multi-nozzle. There are many parameters that affect flame stability in multi-nozzle flame such as nozzle separation distance, fuel flowrates and nozzle configuration, but the most important factor is the existence of nozzles in the center area from the nozzle arrangement. As the number of nozzle in the area is reduced, more air can be entrained into the center of flame base and then tag flame is formed. In the case of circular 8 nozzles, blowout flowrates are above 5.4 times compared with that of single equivalent area nozzle.

• Journal of Advanced Navigation Technology
• /
• v.15 no.2
• /
• pp.227-233
• /
• 2011

This paper presents a small-area ISDB-T time deinterleaver structure. ISDB-T is an mobile TV standard that is widely used in Japan and many South American countries. One of the strong points of the standard is the long interleaving depth, which enhance the communication performance. However, long interleaving requires many delay buffers, in other words many pointer registers. This paper reduces the number of pointer registers with the deinterleaver equivalent transformation. The experimental results show that the area is reduced with the proposed structure.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.4C
• /
• pp.388-397
• /
• 2002

We designed a SIMD-DSP/FPU that can efficiently improve multimedia processing performance when integrated into high-performance embedded microprocessors. We proposed partitioned architectures and new schemes for several functional units to reduce chip area. Sharing functional units reduces the area of FPU significantly. The proposed architecture is modeled in HDL and synthesized with a 0.35$\mu\textrm{m}$ standard cell library. The chip area is estimated to be about 100,000 equivalent gates. The designed unit can run at higher than 50MHz clock frequency of CPU core under the worst-case operating conditions.

• Journal of Multimedia Information System
• /
• v.6 no.1
• /
• pp.7-14
• /
• 2019

This work presents a virtual prototyping design approach for an area-based image stitching hardware. The virtual hardware obtained from virtual prototyping is equivalent to the conceptual algorithm, yet the conceptual blocks are linked to the actual circuit components including the memory, logic gates, and arithmetic units. Through the proposed method, the overall structure, size, and computation speed of the actual hardware can be estimated in the early design stage. As a result, the optimized virtual hardware facilitates the hardware implementation by eliminating trail design and redundant simulation steps to optimize the hardware performance. In order to verify the feasibility of the proposed method, the virtual hardware of an image stitching platform has been realized, where it required 10,522,368 clock cycles to stitch two $1280{\times}1024$ sized images. Furthermore, with a clock frequency of 250MHz, the estimated computation time of the proposed virtual hardware is 0.877sec, which is 10x faster than the software-based image stitch platform using MATLAB.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.45 no.11
• /
• pp.1681-1684
• /
• 2016

Oats (Avena sativa L.) are well known for having high contents of bioactive compounds and health benefits. The objective of this study was to evaluate the antioxidant compounds and antioxidant activities of methanolic extracts from milling fractions and whole grains of oat. The contents of total polyphenolics and flavonoids were analyzed by spectrophotometric methods. ABTS radical and DPPH radical scavenging activities and reducing power were used to compare relative antioxidant activities of milling fractions from oat. Total polyphenolics and flavonoids were much more abundant in oat bran extract than in extracts from whole grain and endosperm. In addition, high levels of ABTS radical (42.34 mg Trolox equivalent antioxidant capacity (TEAC)/100 g sample) and DPPH radical (24.18 mg TEAC/100 g sample) scavenging activities and reducing power ($A_{700}=0.76$) were detected in oat bran. The results of this study indicate that oat bran has significantly higher antioxidant activities and appears to have significant health benefits.

• Korean Journal of Food Science and Technology
• /
• v.50 no.1
• /
• pp.111-116
• /
• 2018

Roasting process of grains modifies their physicochemical characteristics that affect flavor, color, taste, and textures, as well as composition of bioactive compounds. We roasted oats at different temperatures (150, 200, and $250^{\circ}C$) and for different time periods (15 and 30 min). The polyphenol and flavonoid contents in different solvent extracts (methanol, fermented ethanol, and water) were also investigated. The total polyphenol and flavonoid contents were highest in the methanolic extract (135 mg gallic acid equivalent/g and 29 mg catechin equivalent/g, respectively, at $250^{\circ}C/30min$ roasting) and increased with roasting time and temperature. In addition, the avenanthramides were most abundant as accessed ($266{\mu}g/g$) in the methanolic extract upon roasting at $200^{\circ}C$ for 15 min. The radical scavenging activities, using 2,2-diphenyl-1-picrylhydrazyl and 2,2'-azino-bis-3-ethylbenzothiazoline-6-sulphonic acid scavenging, increased with roasting temperature and time. The roasting process may modify the physicochemical structure of oats, thereby, improving polyphenol extraction and antioxidant activity. The results of this study could be used for the manufacture of foods using roasted oats.

• The Journal of Korean Academy of Prosthodontics
• /
• v.28 no.1
• /
• pp.63-94
• /
• 1990

The purpose of this study was to analyze the displacement and the magnitude and the mode of distribution of the stresses in the lower overdenture, the mucous membrane, the abutment tooth and the mandibular supporting bone when various denture base materials, such as acrylic resin and 0.5mm metal base, and various denture base designs were subjected to different loading schemes. For this study, the two-dimensional finite element method was used. Mandibular arch models, with only canine remaining, were fabricated. In the first denture base design, a space, approximately 1mm thick, was prepared between the denture and the dome abutment. In the second denture base design, contact between the denture and the dome abutment was eliminated except the contact of the occlusal third of the abutment. In order to represent the same physiological condition as the fixed areas of the mandible under loading schemes, the eight nodes which lie at the mandibular angle region, the coronoid process and the mandibular condyle were assumed to be fixed. Each model was loaded with a magnitude of 10 kgs on the first molar region(P1) and 7 kgs on the central incisal region (P2) in a vertical direction. Then the force of 10 kgs was applied distributively from the first premolar to the second molar of each model in a vertical direction(P3). The results were as follows. : 1. When the testing vertical loads were given to the selected points of the overdenture, the overdenture showed the rotatory phenomenon, as well as sinking and the displacements of alveolar ridge, abutment and lower border of mandible under the metal base overdenture were less than those under the acrylic resin overdenture. 2. The maximum principal stresses(the maximum tensile stresses) being considered, high tensile stresses occured at the buccal shelf area, the posterior region of the ridge crest and the anterior border region of the mandibular ramus. 3. The minimum principal stresses(the maximum compressive stresses) being considered, high compressive stresses occured at the inferior and posterior border region of the mandible, the mandibular angle and the posterior border region of the mandibular ramus. 4. The vertical load on the central incisal region(P2) produced higher equivalent stress in the mandible than that on any other region(P1, P3) because of the long lever arm distance from the fixed points to the loading point. 5. Higher equivalent stresses were distributed throughout the metal base overdenture than the resin base overdenture under the same loading condition. 6. The case of occlusal third contact of the abutment to the denture produced higher equivalent stresses in the abutment, the mandibular area around the abutment and the overdenture than the case of a 1mm space between the denture and the abutment. 7. Without regard to overdenture base materials and designs, the amounts and distribution patterns of equivalent stresses under the same loading condition were similar in the mucous membrane.