• Transactions on Electrical and Electronic Materials
• /
• 제11권2호
• /
• pp.89-91
• /
• 2010

Partial discharge (PD) resistances were investigated for three types of samples: original epoxy resins, epoxy micro composites with and without the silane processing, and mixture composites with micro and nano particles. The PD was applied to these materials using rod, gap, and plane electrodes. The partial discharge resistance found in the micro composites was better than that found in the original epoxy resin. Moreover, the mixture composites of $SiO_2$ nano and micro particles had much larger resistances than the original epoxy resin or microcomposites. It can be regarded that this excellent property was due to the fact that the nano particles have a dense structure between the micro particles.

• 한국정밀공학회지
• /
• 제10권3호
• /
• pp.31-40
• /
• 1993

The vibration-proof material normally used in structural components of precision machinery or measuring instruments requires higher damping in vibration and better characteristics in dimensional stability and rigidity to accomplish the quality assurance of the products. In this study the ferrite-resin material, which is the mixture of epoxy resin and the oxidized steel (Fe$_{3}$O$_{4}$: ferrite) in consideration of characteristics of aggregator and binder, is developed and investigated as one of vibration-proof materials. Four kinds of composite plates for experiments are made by adding another filler materials such as steel powder, granite powder and carbon-fiber sheet to the basic ferrite-resin matrix. Their characteristics are compared with a cast iron specimen which has the same bending rigidity as other specimens. The ferrite-resin material gives the best damping effect in the motor-induced vibration test. Therefore, the material can be applied to the manufacturing industry for vibration damping of machine elements.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 춘계학술발표대회 논문집
• /
• pp.110-113
• /
• 2001

Dielectrometry has been used to monitor the cure of epoxy resin using composite matrix. In this investigation, physical properties of the mixture of epoxy resin(LY564), bisphenol A type, and cycloaliphatic hardener(HY 2954) were observed. Activation energy at maximum tan $\delta$ and gelation point was determined during isothermal scanning. From IonViscosity data, it was found that vitrification peak after gelation was appeared on slow heating rate. It was also measured that the duration time for full cure was necessary and it was about 24 hr at $145^{\circ}C$. Therefore, epoxy resin used in this research is required the extended time for full cure.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2000년도 추계학술대회논문집
• /
• pp.69-72
• /
• 2000

In this paper, the electrical properties due to epoxy resin used in transformer of rail road signal are studied. The specimen of epoxy resin was hardened as each 3[h], 4[h], 5[h] in this experiment. In order to measure the conductivity properties, the highmegohm meter is used at temperature 25 to 140[$^{\circ}C$] and applying voltage 100 to 1000[V]. As a result of this experiment, we confirmed that 3[h] specimen is better than the others.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 추계학술발표대회 논문집
• /
• pp.111-114
• /
• 2003

Thermosets are highly cross-linked polymers with a three-dimensional molecular structure. The network structure gives rise to mechanical properties, however, one major drawback of thermosets, which also results from their network structure, is their poor resistance to impact and to crack initiation. In this study, to solve this problem, the reactive thermoplastics such as amine terminated polyetherimide (ATPEI), ATPEI-CTBN-ATPEI(ABA) triblock copolymer, CTBN-ATPEI(AB) diblock copolymer, and carboxyl group modified ATPEI was synthesized, after that blended with epoxy resin, and the carbon fiber reinforced composites were fabricated. The impact load, energy, and delamination were investigated by using drop weight impact test and C-scan test. As a results, the ABA/epoxy blend system showed good impact properties.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 춘계학술대회 논문집
• /
• pp.285-288
• /
• 1998

Ultrasonic signal characteristics related with the growth of electrical trees in epoxy resin are examined under 67[Hz] ac voltage application along with a CCD camera and PD current method. The ultrasonic sensor with a resonant frequency of 200[Hz] supported by a mechanical spring is attached directly to the lower-side of plane electrode. The magnitude of Partial discharge and count rate of ultrasonic signals have been measured according to the tree growth from a needle tip in an epoxy sample.

• Fibers and Polymers
• /
• 제5권4호
• /
• pp.259-263
• /
• 2004

Rubber-modified epoxy resins have been employed as adhesive and matrix materials for glass and corbon-fiber composites. The behavior of fracture around a crack tip for rubber-modified epoxy resin is investigated through the acoustic emission (AE) analysis of compact tension specimens. Damage zone and rubber particles distributed around a crack tip were observed by a polarized optical microscope and an atomic force microscope (AFM). The damage zone in front of pre-crack tip in rubber-modified specimen $(15wt\%\; rubber)$ began to form at about $13\%$ level of the fracture load and grew in size until $57\%$ load level. After that, the crack propagated in a stick-slip manner. Based on time-frequency analysis of AE signals and microscopic observation of damage zone, it was thought that AE signals with frequency bands of 0.15-0.20 MHz and 0.20­0.30 MHz were generated from cavitation in the damage zone and crack propagation, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 추계학술대회 논문집
• /
• pp.69-72
• /
• 2000

In this paper, the electrical properties due to epoxy resin used in transformer of rail road signal are studied. The specimen of epoxy resin was hardened as each 3[h], 4[h], 5[h] in this experiment. In order to measure the conductivity properties, the highmegohm meter is used at temperature 25 to 140[$^{\circ}C$] and applying voltage 100 to 1000[V]. As a result of this experiment, we confirmed that 3[h] specimen is better than the others.

• 보존과학회지
• /
• 제30권2호
• /
• pp.181-187
• /
• 2014

도자기 복원용으로 가장 많이 사용되고 있는 에폭시 복원제는 높은 접착력, 저수축, 고강도 등의 조건을 충족시키지만 에폭시 수지(Epoxy resin) 자체의 황변 현상으로 인하여 복원 후 시간이 경과함에 따라 복원부의 색이 변하는 단점을 지니고 있다. 본 연구에서는 도자기 복원용으로 사용되고 있는 에폭시 수지(Epoxy resin)의 문제점인 황변 현상을 대폭줄인 저황변 및 접착력과 고강도를 가진 복원제를 개발하고자 하였다. 기존 에폭시 재료 중에 도자기 복원 재료로 많이 사용되고 있는 EPO-TEK301$^{(R)}$, L30$^{(R)}$, XTR-311$^{(R)}$ 등과 비교하여 접착력과 강도 등의 물성을 가지면서 황변성이 거의 없는 복원제를 개발하고자 하였다. 접착력은 개발된 수지가 2.51 MPa를 나타내도록 하여, 최고의 접착력을 나타내는 XTR-311$^{(R)}$ 2.30 MPa를 능가하도록 하였으며 1.21 MPa를 나타내는 EPO-TEK301$^{(R)}$이나 1.81 MPa을 나타내는 L30$^{(R)}$보다 약 2 배의 접착력을 나타내 도록하였다. 특히 에폭시 수지(Epoxy resin)가 지니고 있는 황변 현상 실험 결과 ${\Delta}E^*ab$ 색상 변화량의 변화 값이 10 ~ 25 정도의 변화량을 나타내고 있지만 개발된 저황변 에폭시 수지(Epoxy resin)의 경우 원액 기준 ${\Delta}E^*ab$ 색상 변화 값이 8.3으로 기존의 재료들 보다 1 ~ 3 배 정도 황변 현상을 줄여 황변 현상으로 인한 색상의 변화에 따른 이질감에 대한 문제점을 해결하였다.

• 한국산업융합학회 논문집
• /
• 제10권4호
• /
• pp.207-211
• /
• 2007

The durable lifetime of RC structures is shortened by various reasons, which are the generation of cracks in construction and service term, the exterior deterioration according to climatic condition, the surface damage due to chloride attack and the corrosion of reinforced bars. The durability of concrete structures is nevertheless able to be increased by the method and the material of reinforcement and repair. The epoxy resin is widely used for reinforment and repair of concrete because of the superiority in mechanical property, adhesive property, abrasion resistance, impact resistance and chemical resistance. The epoxy cement mortar with hardening agent has a lot of disadvantages that are troublesome mixing work, weakened weatherability and high cost for hardening agent. In this study, the mix proportion of mortar is presented just only with epoxy resin and some admixtures, and the test result of mortar without hardening agent shows the higher strength than the mortar with hardening agent. In the mix proportion, the weight of epoxy resin must be less than 15% of the unit weight of cement, and 10% of unit weight of cement is adequate for the weight of admixtures.