• Journal of Environmental Science International
• /
• v.2 no.4
• /
• pp.325-330
• /
• 1993

A number of experiments were conducted in order to investigate the organic removal efficiency and biomass characteristics according to the organic shock loading rate in a fluidized bed biofilm reactor. At the operation conditions of HRT, 8.44 hour, superficial upflow velocity, 0.9 cm/sec and temperature, 22$\pm$$1^{\circ}C$, the removal efficiency of SCOD was founded to be 96.5, 92 and 90 % with the organic shock loading rate of 3.5, 10.8 and 33 kgCOD/m$^3$ㆍday, respectively. Within the F/M ratio ranged 0.4 to 2.0 kgCOD/kgVSSㆍday, the SCOD removal efficiency was shown as 90% at F/M ratio of 2.0 kgCOD/kgVSSㆍday, but the TCOD removal efficiency was 72 % at F/M ratio of 1.8 kgCOD/kgVSSㆍday. The average biomass concentrations were 7800, 14950 and 27532 mg/l on the organic shock loading rate of 3.5, 10.8 and 33 kgCOD/$\textrm{m}^3$ㆍday, respectively. This result was agreed with the fact that more biomass could be produced at high concentration of substrate, but some biomass was detached at the onset of shock and easily acclimated at the shock condition.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.6
• /
• pp.5-15
• /
• 2011

In this study, centrifuge model tests were performed to investigate stress concentration ratio, stress characteristics of soft clay ground improved by granular compaction piles with changes of piles type, loading condition and area replacement ratio. From the results of rigid loading tests, while vertical stresses acting on clay ground is similar, vertical stresses acting on GCP is larger than those acting on SCP with same replacement ratio. Also, average stress concentration ratio is increased proportionally with increasing the area replacement ratio of GCP and SCP. It was evaluated that average stress concentration ratio of soft clay ground improved by GCP is larger than that of SCP. As a result of flexible loading tests, stress concentration ratio is the highest when replacement ratio of GCP and SCP is 40%. Average stress concentration ratio of soft clay ground improved by GCP is a little more higher than is improved by SCP.

• Journal of Environmental Science International
• /
• v.9 no.6
• /
• pp.449-454
• /
• 2000

Sustainable development has been the key concept, both in economic policies and in environmental management. On the basis of an systems ecology perspective, this suggests the sustainable development of Korea\`s natural environment and economic activity using the EMERGY evaluation. The total EMERGY use(7,730E20sej/yr) in Korea is 81 percent from imported sources, fuels and goods and services. The ratio of outside investment to attracting natural resources is already large, like other industrialized countries. Continued availability of purchased inputs at a favorable balance of EMERGY trade, currently about 2.85 to 1 net EMERGY, tis the basis for present economic activity and must decrease as the net EMERGY of purchased inputs including fossil fuels goes down. EMERGY yield ratio and environmental loading ratio were 1.23 and 20.30, respectively. The population level is already in excess of carrying capacity. Its carrying capacity for steady state on its renewable sources is only 2.2 million people, compared to 45.9 million in 1977. EMERGY sustainability index is therefore less than one, which is indicative of highly developed consumer oriented economies. Until now the development of a country has been achieved by the economic growth, but it can be sustained in the long run by the use of renewable resource systems. the efficiency of energy usage, and the transformation of the social-economic structure based on an ecological-recycling concept.

• Journal of environmental and Sanitary engineering
• /
• v.12 no.3
• /
• pp.95-102
• /
• 1997

The process which can stabilize water quality of treatment and improve nitrogen removal rate under the condition of high organic loading was developed by charging fibrous HBC media to single sludge nitrification-denitrification process. This process was operated easier, minimized the treatment cost, and shortened the retention time. To improve T-N removal rate, a part of nitrifing liquid at aerobic zone was recycled to anoxic zone by approximate internal recycle ratio. The experimental results are as follows ; T-N removal efficiency in the organic volumetric loading 0.14-0.19 kg/COD/m$^{3}$·d was obtained asmaxium of 85% at internal recycle ratio 2.5 and in more ratio than this it was decreased. Organic removal efficiency was about 91% under the overall experimental conditions and not influenced by recycle ratio.

• Structural Engineering and Mechanics
• /
• v.30 no.2
• /
• pp.177-190
• /
• 2008

Material failure behavior is generally dependent on loading rate. Especially in brittle and quasi-brittle materials, rate dependent material behavior can be significant. Empirical formulations are often used to predict the rate dependency, but such methods depend on extensive experimental works and are limited by practical constraints of physical testing. Numerical simulation can be an effective means for extracting knowledge about rate dependent behavior and for complementing the results obtained by testing. In this paper, the failure behavior of a brittle material under different loading rates is simulated by molecular dynamics analysis. A notched specimen is modeled by sub-million particles with a normalization scheme. Lennard-Jones potential is used to describe the interparticle force. Numerical simulations are performed with six different loading rates in a direct tensile test, where the loading velocity is normalized to the ratio of the pseudo-sonic speed. As a consequence, dynamic features are achieved from the numerical experiments. Remarkable failure characteristics, such as crack surface interaction/crack arrest, branching, and void nucleation, vary in case of the six loading cases. These characteristics are interpreted by the energy concept approach. This study provides insight into the change in dynamic failure mechanism under different loading rates.

• Computers and Concrete
• /
• v.33 no.4
• /
• pp.399-407
• /
• 2024

This study nondestructively examined the evolution of crack density in ultra-high performance concrete (UHPC) upon cyclic loading. Uniaxial compression was repeatedly applied to the cylindrical specimens at levels corresponding to 32% and 53% of the maximum load-bearing capacity, each at a steady strain rate. At each stage, both P-wave and S-wave velocities were measured in the absence of the applied load. In particular, the continuous monitoring of P-wave velocity from the first loading prior to the second loading allowed real-time observation of the strengthening effect during loading and the recovery effect afterwards. Increasing the number of cycles resulted in the reduction of both elastic wave velocities and Young's modulus, along with a slight rise in Poisson's ratio in both tested cases. The computed crack density showed a monotonically increasing trend with repeated loading, more significant at 53% than at 32% loading. Furthermore, the spatial distribution of the crack density along the height was achieved, validating the directional dependency of microcracking development. This study demonstrated the capability of the crack density to capture the evolution of microcracks in UHPC under cyclic loading condition, as an early-stage damage indicator.

• Structural Engineering and Mechanics
• /
• v.31 no.6
• /
• pp.679-696
• /
• 2009

The paper aims at analyzing the stress distribution around an underground opening that is subjected to non-symmetrical surface loading with emphasis on opening shapes with sharp corners and the stress concentrations developed at these locations. The analysis is performed utilizing the BIE method coupled with the Neumann's series. In order to implement this approach, the special recurrent relations for half plane were proven and the modified Shanks transform was incorporated to accelerate the series convergence. To demonstrate the capability of the developed approach, a horseshoe shape opening with sharp corners was investigated and the location and magnitude of the maximum hoop stress was calculated. The dependence of the maximum hoop stress location on the parameters of the surface loading (degree of asymmetry, size of loaded area) and of the opening (the opening height) was studied. It was found that the absolute magnitude of the maximum hoop stress (for all possible surface loading locations) is developed at the roof points when the opening height/width ratio is relatively large or when the pressure loading area is relatively narrow (compared to the roof arch radius), and contrarily, when the opening height/width ratio is relatively small or when the surface pressure is applied to a relatively wide area, the absolute magnitude of the maximum hoop stress is developed at the bottom sharp corner points.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.6C
• /
• pp.379-388
• /
• 2008

In the bi-directional pile load test (BD PLT) for pile load tests of Mega pile foundations, loading capacity standard is not specified exactly. Therefore there are so many confusions in performing the BD PLT and variations up to maximum 2 times in loading capacity are come out. In this study, standards of bi-directional pile load test (BD PLT) were considered. Based on cases of the bi-directional pile load test performed in domestic areas, maximum equivalent test load, test load increasing ratio, loading capacity increasing ratio and sufficiency ratio of design load were analyzed. It could be known that the loading capacity standard of bi-directional pile load test must be defined as 1-directional loading capacity and also must be established as more than 2 times of design load.

• Journal of Environmental Science International
• /
• v.9 no.1
• /
• pp.49-55
• /
• 2000

An EMERGY analysis of the main energy flows driving the economy of humans and life support systems consists of environmental energies, fuels, and imports, all expresses as solar emjoules. Total EMERGY use(720.0 E20 sej/yr) of the Nakdong River Basin is 96 per cent from imported sources, fuels and goods and services. EMERGY flows from the environment such as rain and geological uplift flux accounted for only 4 percent of total EMERGY use. Consequently, the ratio of outside investment to attracting natural resources was large, like other industrialized areas. EMERGY use per person in the Nakdong River Basin indicates a moderate EMERGY standard of living, even though the indigenous resources are very poor. Population of 6.66 million people in 1996 is already in excess of carrying capacity of the basin. Carrying capacity for steady state based on its renewable sources in only 0.226 million people. EMERGY yield ratio and environment loading ratio were 1.07 and 28.52, respectively. EMERGY sustainability index, a ratio of EMERGY yield ratio to environment loading ratio, is therefore less than one, which is indicative of highly developed consumer oriented economies. This study suggests that the economic structure of the Nakdong River Basin should be transformed from the present industrial structure to the social-economic structure based on an ecological-recycling concept for the sustainable use of the Nakdong River.

• Environmental Engineering Research
• /
• v.19 no.4
• /
• pp.395-399
• /
• 2014

Operation characteristics of the sequencing batch reactor (SBR) process with electro-flotation (EF) as a solid liquid separation method (EF-SBR) were investigated. EF-SBR process showed excellent solid-liquid separation performance which enabled to separate biosolids from liquid phase within 30 min and to extend cyclic reaction time. Although influent organic loading rate was increased stepwise from 5 to 15 g COD/day, food to microorganisms (F/M) ratio could be maintained about 0.3 g COD/g VSS/day in EF-SBR because biomass concentration could be easily controlled at desired level by EF. However, it was impossible to increase biomass concentration at the same level in control SBR (C-SBR) process because solid-liquid separation by gravity settling showed a limitation at higher mixed liquor suspended solids (MLSS) concentration with 60 min of settling time. Total chemical oxygen demand (TCOD) removal efficiency of EF-SBR process was not decreased although influent organic loading rate became 3 times higher than initial value. However, it was seriously deteriorated in C-SBR process after increasing the rate over 10 g COD/day, which was accounted for insufficient organic removal by relatively higher food to microorganisms (F/M) ratio as well as biosolids wash-out by a limitation of gravity sedimentation.