• 한국전기전자재료학회논문지
• /
• 제35권3호
• /
• pp.269-274
• /
• 2022

We prepared carbon nanotube (CNT) paper by a vacuum filtration method for the use of a chip-typed resistor as a precision passive device with a constant resistance. Hybrid resistor composed of the CNT resistor with a negative temperature coefficient of resistance (T.C.R) and a metal alloy resistor with a positive T.C.R could lead to a constant resistance, because the resistance increase owing to the temperature increase at the metal alloy and decrease at the CNT could counterbalance each other. The constant resistance for the precision passive devices should be maintained even when a heat was generated by a current flow resulting in resistance change. Performance reliabilities of the CNT resistor for the precision passive device applications such as electrical load limit, environmental load limit, and life limit specified in IEC 60115-1 must be ensured. In this study, therefore, the rated power determination and T.C.R tests of the CNT paper were conducted. -900~-700 ppm/℃ of TCR, 0.1~0.2 A of the carrying current capacity, and 0.0625~0.125 W of the rated power limit were obtained from the CNT paper. Consequently, we confirmed that the application of CNT materials for the precision hybrid passive devices with a metal alloy could result in a better performance reliability with a zero tolerance.

• 콘크리트학회논문집
• /
• 제26권3호
• /
• pp.267-275
• /
• 2014

최근 곡선교 사용이 증가함에 따라 기존 곡선 교량의 한계점을 극복하고자 PSC 곡선 주형을 이용한 곡선교에 대한 해석적 연구가 활발히 진행되고 있다. 그러나 기존의 프레임 요소를 이용한 격자해석방법으로는 PSC 곡선교에 대한 정밀해석이 어렵다. 이에 따라 이 연구에서는 PSC 곡선교의 정밀 유한 요소 해석을 실시하여 프리캐스트 PSC 곡선교의 설계를 위한 참고자료로 사용하고자 한다. 이를 위하여 3차원 솔리드 요소를 사용한 모델링을 실시하고, 거더 수, 하중 재하 위치, 단면 변화, 긴장력 변화 및 편긴장력 도입 여부와 같은 매개변수에 대한 거동을 평가하였다. 해석 결과 경간장 50 m 3주형 교량의 항복하중과 파괴 하중이 경간장 40 m 2주형 교량에 비해 200% 이상의 성능을 보였고, 외측거더에 하중을 가하였을 경우 도심의 위치에 따라 하중저항력 및 거더 간의 처짐 편차가 낮게 평가되는 것으로 나타났다. 또한 거더 단면을 변화시킨 경우 단면의 증가에 따라 구조성능이 향상되는 것으로 나타났으나 PS도입량의 변화에 의한 효과에 비해 경제성과 시공성에서 불리한 것으로 나타났다. PS 도입량 변화에 따른 영향을 분석한 결과 PS 도입량이 증가함에 따라 솟음량과 하중저항력이 비례하여 증가하였으며 거더 간 처짐 편차가 줄어드는 경향을 보였다. 또한, 편긴장력을 도입하였을 시 도입량 증가에 비례하여 내외측 거더 모두에서 하중저항력이 증가하며, 특히 외측거더에 편긴장력이 도입되었을 때 더 우수한 성능을 보이는 것으로 나타나, PSC 곡선교의 경제성 및 안정성을 확보하는데 효율적인 것으로 나타났다.

• 대한토목학회논문집
• /
• 제3권4호
• /
• pp.133-142
• /
• 1983

말뚝의 동적(動的) 지지력(支持力)을 더욱 정확(正確)하게 추정(推定)하기 위하여 파동이론(波動理論)과 잔류응력(殘留應力)을 고려(考慮)하여 유도(誘導)된 필자(筆者)의 새로운 공식(公式)을 말뚝의 재하시험자료(載荷試驗資料)를 이용(利用)하여 통계적(統計的) 분석(分析) 방법(方法)으로 다른 대표적(代表的) 공식(公式)과 비교(比較)하여 평가(評價)하였다. 그 결과(結果), 새로운 공식(公式)은 그 안전율(安全率)이 3 이하(以下)이며, 비교적(比較的) 정확도(精確度)가 높은 것으로 평가(評價)되었다.

• Structural Engineering and Mechanics
• /
• 제18권5호
• /
• pp.609-626
• /
• 2004

The Land Transport Authority of Singapore has a continuing program of highway bridge upgrading, to refurbish and strengthen bridges to allow for increasing vehicle traffic and increasing axle loads. One subject of this program has been a short span bridge taking a busy highway across a coastal inlet near a major port facility. Experiment-based structural assessments of the bridge were conducted before and after upgrading works including strengthening. Each assessment exercise comprised two separate components; a strain and acceleration monitoring exercise lasting approximately one month, and a full-scale dynamic test carried out in a single day. This paper reports the application of extreme value statistics to estimate bridge live loads using strain measurements.

• Structural Engineering and Mechanics
• /
• 제9권2호
• /
• pp.111-126
• /
• 2000

Truss type structures are attractive to a variety of engineering applications on earth as well as in space due to their high stiffness to mass ratios and ease of construction and fabrication. During the service life, an individual member of a truss structure may lose load carrying capacity due to many reasons, which may lead to collapse of the structure. An analytical and computational procedure has been developed to study the response of truss structures subject to member failure under static and dynamic loadings. Emphasis is given to the dynamic effects of member failure and the propagation of local damage to other parts of the structure. The methodology developed is based on nonlinear finite element analysis technique and considers elasto-plastic material nonlinearity, postbuckling of members, and large deformation geometric nonlinearity. The pseudo force approach is used to represent the member failure. Results obtained for a planar nine-bay indeterminate truss undergoing sequential member failure show that failure of one member can initiate failure of several members in the structure.

• Steel and Composite Structures
• /
• 제7권6호
• /
• pp.421-440
• /
• 2007

An optimal design method in cooperated with nonlinear inelastic analysis is presented. The proposed nonlinear inelastic method overcomes the difficulties due to incompatibility between the elastic global analysis and the limit state member design in the conventional LRFD method. The genetic algorithm used is a procedure based on Darwinian notions of survival of the fittest, where selection, crossover, and mutation operators are used to look for high performance ones among sections in the database. They are satisfied with the constraint functions and give the lightest weight to the structure. The objective function taken is the total weight of the steel structure and the constraint functions are load-carrying capacity, serviceability, and ductility requirement. Case studies of a planar portal frame, a space two-story frame, and a three-dimensional steel arch bridge are presented.

• Structural Engineering and Mechanics
• /
• 제56권6호
• /
• pp.983-1001
• /
• 2015

This study focuses on the load carrying capacity and the force transfer mechanism of multi-hole perfobond shear connectors in steel-concrete composite structure. The behavior of multi-hole perfobond shear connector is more complicated than single-hole connector cases. 2 groups push-out tests were conducted. Based on the test results, behavior of the connection was analyzed and the failure mechanism was identified. Simplified iterative method and analytic solution were proposed based on force equilibrium for analyzing multi-hole perfobond shear connector performance. Finally, the sensitivity of design parameters of multi-hole perfobond shear connector was investigated. The results of this research showed that shear force distribution curve of multi-hole perfobond shear connector is near catenary. Shear forces distribution were determined by stiffness ratio of steel to concrete member, stiffness ratio of shear connector to steel member, and number of row. Efficiency coefficient was proposed to should be taking into account in different limit state.

• 한국해양공학회지
• /
• 제18권4호
• /
• pp.46-51
• /
• 2004

The surface layer in dredged and reclaimed marine clay is improved by mixing of shallow soils and hardening agents, which is made of cement, containing some other special admixtures. Tests in both laboratory and field settings are performed to investigate the improvement effect and strength properties of cement-stabilized soils. The test results show that the hardening agent sufficiently improves the soil properties of the surface layer, while increasing the load-carrying capacity. The strength of cement-stabilized soils depends, primarily, on water-to-cement ratio and curing temperature. That is, the higher curing temperature and the longer curing time, the higher the strength in cement-stabilized soils. The high ratio of water-ta-cement results in a lower strength.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.1488-1489
• /
• 2007

This paper described the current rating methodology of high voltage connectors used for high efficient vehicles. Typically, temperature rise at rated current has been used to rate power contacts in automotive connector. However, for automotive applications, they are required to meet severe environmental conditions and high connector reliability. Therefore, it is very important to rate correctly an allowable current of automotive connector. We have measured the contact characteristics through current cycling at room temperature and at high temperature, as well as temperature rising and current carrying capacity by de-rating. From the above results, we have developed high reliable contacts with about 80 Amperes.

• Steel and Composite Structures
• /
• 제35권5호
• /
• pp.701-715
• /
• 2020

Steel storage racks are lightweight structures, made of thin-walled cold-formed members, whose behaviour is remarkably influenced by local, distortional and overall buckling phenomena, frequently mutually combined. In addition, the need of an easy and rapid erection and reconfiguration of the skeleton frame usually entails the presence of regular perforations along the length of the vertical elements (uprights). Holes and slots strongly influence their behaviour, whose prediction is however of paramount importance to guarantee an efficient design and a safe use of racks. This paper focuses on the behaviour of isolated uprights subjected to both axial load and bending moments, differing for the cross-section geometry and for the regular perforation systems. According to the European standards for routine design, four alternatives to evaluate the bending moment-axial load resisting domains are shortly discussed and critically compared in terms of member load carrying capacity.