• Title/Summary/Keyword: Entry Speed

Search Result 163, Processing Time 0.027 seconds

Numerical and experimental study of cone-headed projectile entering water vertically based on MMALE method

  • Cao, Miaomiao;Shao, Zhiyu;Wu, Siyu;Dong, Chaochao;Yang, Xiaotian
    • International Journal of Naval Architecture and Ocean Engineering
    • /
    • v.13 no.1
    • /
    • pp.877-888
    • /
    • 2021
  • The water entry behaviors of projectiles with different cone-headed angles were studied numerically, experimentally and theoretically, mainly focusing on the hydrodynamic impact in the initial stage. Based on MMALE algorithm, it was proposed a formula of impact deceleration, which relied on the initial entry velocity and cone-headed angle. Meanwhile, in order to verify the validity of the simulation model, experiments using accelerometer and high-speed camera were carried out, and their results were in a good agreement with simulation results. Also, theoretical calculation results of cavity diameter were compared with experiments and simulation results. It was observed that the simulation method had a good reliability, which would make forecast on impact deceleration in an engineering project.

An Analysis of Roundabout Application Effects Based on Before and After Field Studies (사전·사후 비교분석을 통한 회전교차로 도입 효과분석)

  • Lee, Dongmin;You, Jungho;Kim, Dohoon;Lee, Sukki
    • International Journal of Highway Engineering
    • /
    • v.15 no.1
    • /
    • pp.111-119
    • /
    • 2013
  • PURPOSES: Though the situation that the roundabouts are actively constructed, researches on the effect of the roundabouts focus mainly on the analysis of the expected effects of using only traffic simulation on the operation. Considering such problems, this study is conducted to analyze the effects of the various aspects based on field observation studies. METHODS: This study evaluated and analyzed the effects from the aspects of traffic operation, traffic safety, and traffic behavior by performing field observation studies with six roundabouts with/without signal controls on the pilot project areas for the roundabouts installed in 2010. RESULTS: Through the study results, it was found that the average travel time decreases by 14.7% and 2.4% on the signalized intersections and unsignalized intersections, respectively. The average travel speed increases by 9.7 and 5.8km/h on the roundabouts with/without signal lights. Regarding traffic safety, the speed deviation among individual vehicles decreases by approximately 18.4 to 32.7km/h, thus confirming the safety effects. As the decrease of the number of conflicts, it might be explained that car crashes and collision with pedestrians decreased by 62.2% and 66.7%. Also the result shows that the lowest point of speed in roundabouts appears near the yield line on the entry area on the roundabouts. When passing through the roundabouts, vehicles enter at a speed of 20-30km/h, which is the design speed of the circulatory lane and drive out the roundabout with a higher speed than the entry speed. CONCLUSIONS: When a roundabout is introduced at the intersections below certain traffic volume there are effects of traffic operation, traffic safety, and traffic behavior.

Approximation Method to Estimate Water Entry Impact Forces Acting on Light Weight Torpedo (경어뢰 입수 충격력의 근사화)

  • Chan-Ki Kim
    • Journal of the Society of Naval Architects of Korea
    • /
    • v.37 no.2
    • /
    • pp.77-87
    • /
    • 2000
  • The water entry forces acting on an air-dropped torpedo are of the restrictions on launch speed and launch altitude, because it could cause the structural damage to components of torpedo. Therefore, it is necessary to estimate the water entry forces with confidence according to launch conditions. In this study, an approximation method for water entry forces is presented, and the results using this approximation are compared with those of other numerical methods. The magnitude and duration of impact forces estimated by the present approximation agree with those of impact by the analysis of ideal or viscous flow. This method can give useful tools to select the launch in initial design stage.

  • PDF

Comparison of Ballistic-Coefficient-Based Estimation Algorithms for Precise Tracking of a Re-Entry Vehicle and its Impact Point Prediction

  • Moon, Kyung Rok;Kim, Tae Han;Song, Taek Lyul
    • Journal of Astronomy and Space Sciences
    • /
    • v.29 no.4
    • /
    • pp.363-374
    • /
    • 2012
  • This paper studies the problem of tracking a re-entry vehicle (RV) in order to predict its impact point on the ground. Re-entry target dynamics combined with super-high speed has a complex non-linearity due to ballistic coefficient variations. However, it is difficult to construct a database for the ballistic coefficient of a unknown vehicle for a wide range of variations, thus the reliability of target tracking performance cannot be guaranteed if accurate ballistic coefficient estimation is not achieved. Various techniques for ballistic coefficient estimation have been previously proposed, but limitations exist for the estimation of non-linear parts accurately without obtaining prior information. In this paper we propose the ballistic coefficient ${\beta}$ model-based interacting multiple model-extended Kalman filter (${\beta}$-IMM-EKF) for precise tracking of an RV. To evaluate the performance, other ballistic coefficient model based filters, which are gamma augmented filter, gamma bootstrapped filter were compared and assessed with the proposed ${\beta}$-IMM-EKF for precise tracking of an RV.

Necessity of Climbing Lane on SMART Highway and its Design Guidelines (SMART Highway 오르막차로 설치 필요성 및 기준 연구)

  • Kim, Sang Gu;Kim, Young Chun;Sim, Dae Young;Lee, Yong Mun;Kim, Jong Won;Kim, Heung Rae
    • Journal of Korean Society of Transportation
    • /
    • v.32 no.5
    • /
    • pp.473-486
    • /
    • 2014
  • This study aims to review whether climbing lane installment is needed by analyzing the impact that standard trucks have on traffic according to vertical alignment at SMART highway, and if climbing lanes are required to propose truck speed change curves based on slope length. We used VISSIM simulation model to obtain the speed change of the standard truck on uphill roads. The standard truck on climbing lanes was set for 100kg/kW (170lb/hp) with the entry speeds set and analyzed by 90, 100, and 110 km/h considering the future speed limit of trucks. The results of the research show that under SMART highway circumstance, the 1 and 2% vertical alignment is not needed at the climbing lane but 3% vertical alignment is necessary. In order to install the climbing lane at 3% vertical alignment, the speed change curve of truck depending on slope length of 90, 100, and 110km/h of entry speed is proposed.

A Development of the Design Guidelines for Connecting Roads in Highway Rest Area (고속도로 휴게소 연결로 설계 기준 설정에 관한 연구)

  • Lee, Choulsoo;Won, Jaimu
    • International Journal of Highway Engineering
    • /
    • v.15 no.1
    • /
    • pp.143-154
    • /
    • 2013
  • PURPOSES: Design of approach roads of rest areas in highway has many drawbacks such as geometric design elements. There has been traffic accidents occured in these approach roads of rest areas. Thus, design criteria is required in order to protect accidents from being occurred. In case of Korea, geometric structure design criteria of entry facilities, such as toll-gate, interchange, junction etc was established. However there are no presence in a detailed standards for geometric structure of the rest area which affiliated road facilities. METHODS: In this study, analytic on accidents was carried out in regards to the entry of geometric structure of resting areas by utilizing a sight survey and an investigation research of traffic accidents. The survey was targeting 135 general service areas. Collisions with physical channelization and safety facilities occurred due to speeding, rapid entry, and etc at the entrance nose section. At the entrance connector roads, accidents caused by speeding, negligence, over-operation of handle of drivers were main reason of accidents. Discriminant analysis were conducted about geometric elements to distinguish influencing factors for traffic accidents. the lengths and access angles of the entrance connector roads were regarded as to have the high relation with traffic accidents. RESULTS: After classifying the design section of resting areas' entry as well as derive design elements on each section, a speed measurement by targeting entry of rest areas and car behavior surveys were performed, then each element's minimum standard was derived through the analyses. According to the speeds at the starting/end point of entrance connector road, the range of the junction setting angle of the entrance connector road is defined as $12^{\circ}{\sim}17^{\circ}$ and the connector length model was suggested. CONCLUSIONS: Suggest improvement plans for existing rest areas that can be applied realistically. This should be corresponded to the standards of entry and exit of developed rest areas.

Effect of the Introduction of High-speed Trains on Consumer Welfare

  • BAEK, JISUN
    • KDI Journal of Economic Policy
    • /
    • v.38 no.1
    • /
    • pp.23-52
    • /
    • 2016
  • This paper examines the impact of introducing high-speed trains on consumer welfare, taking the ensuing changes in train schedules into account. Based on the estimated demand model for travel which incorporates consumer's heterogeneous preferences for travel schedules into the standard discrete-choice model, I separately evaluate the impact from adding high-speed trains and that from changes in train schedules. The results indicate that consumers who travel between two cities connected by high-speed trains benefit from the introduction of high-speed trains, while some travelers whose choice set does not include high-speed trains face a reduced frequency of non-high-speed trains, resulting in significant losses.

  • PDF

Targeting a Safe Entry Point for C2 Pedicle Screw Fixation in Patients with Atlantoaxial Instability

  • Chun, Hyoung-Joon;Bak, Koang-Hum
    • Journal of Korean Neurosurgical Society
    • /
    • v.49 no.6
    • /
    • pp.351-354
    • /
    • 2011
  • Objective : This investigation was conducted to evaluate a new, safe entry point for the C2 pedicle screw, determined using the anatomical landmarks of the C2 lateral mass, the lamina, and the isthmus of the pars interarticularis. Methods : Fifteen patients underwent bilateral C1 lateral mass-C2 pedicle screw fixation, combined with posterior wiring. The C2 pedicle screw was inserted at the entry point determined using the following method : 4 mm lateral to and 4 mm inferior to the transitional point (from the superior end line of the lamina to the isthmus of the pars interarticularis). After a small hole was made with a high-speed drill, the taper was inserted with a 30 degree convergence in the cephalad direction. Other surgical procedures were performed according to Harm's description. Preoperatively, careful evaluation was performed with a cervical X-ray for C1-C2 alignment, magnetic resonance imaging for spinal cord and ligamentous structures, and a contrast-enhanced 3-dimensional computed tomogram (3-D CT) for bony anatomy and the course of the vertebral artery. A 3-D CT was checked postoperatively to evaluate screw placement Results : Bone fusion was achieved in all 15 patients (100%) without screw violation into the spinal canal, vertebral artery injury, or hardware failure. Occipital neuralgia developed in one patient, but this subsided after a C2 ganglion block. Conclusion : C2 transpedicular screw fixation can be easily and safely performed using the entry point of the present study. However, careful preoperative radiographic evaluation, regardless of methods, is mandatory.

Development of Rolling Speed Set-up Model for the Travelling Stability in Hot Strip Finishing Mill (열간사상압연 통판안정성 개선을 위한 속도설정모델 개발)

  • 문영훈;김영환
    • Proceedings of the Korean Society for Technology of Plasticity Conference
    • /
    • 1999.08a
    • /
    • pp.47-56
    • /
    • 1999
  • New rolling speed prediction model has been developed for the precise presetting rolling speed of each finishing mill stand in the tandem hot strip mill. Those factors such as neutral point, work roll diameter, rolling torque, friction coefficient, bite angle and the thickness at each side of entry and deliver of the rolls were taken into account. To consider width effect on forward slip, calibration factors obtained from rolling torque has been added to new prediction model and refining method has also been developed to reduce the speed unbalance between adjacent stands. The application of the new model showed a good agreement in rolling speeds between the predictions and the actual measurements, and the standard deviation of prediction error has also been significantly reduced.

  • PDF

Traffic Accident Model of Roundabout based on Type of Land Use (토지이용 유형별 회전교차로 교통사고모형)

  • Lee, Min Yeong;Park, Byung Ho
    • International Journal of Highway Engineering
    • /
    • v.18 no.6
    • /
    • pp.153-160
    • /
    • 2016
  • OBJECTIVES : The objective of this study is to develop a traffic accident model of a roundabout based on the type of land use. METHODS : The traffic accident data from 2010 to 2014 were collected from the "traffic accident analysis system (TAAS)" data set of the Road Traffic Authority. A multiple linear regression model was utilized in this study to analyze the accidents based on the type of land use. Variables such as geometry and traffic volume were used to develop the accident models based on the type of land use. RESULTS : The main results are as follows. First, the null hypothesis that the type of land use does not affect the number of accidents is rejected. Second, four accident models based on the type of land use have been developed, which are statistically significant (high $R^2$ values). Finally, the total entering and circulating volumes, area of the central island, number of speed breakers, mean number of entry lanes, diameter of the inscribed circle, mean width of the entry lane, area of the roundabout, bus stops, and number of circulatory roadways are analyzed to see how they affect the accident for each type of land use. CONCLUSIONS : The development of the accident models based on the type of land use has revealed that the accident factors at a roundabout are different for each case. Thus, more speed breakers in commercial areas and an inscribed circle of proper diameter in commercial and residential areas are determined to be important for reducing the number of accidents. Additionally, expanding the width of the entry lanes, decreasing the area of the roundabouts in residential areas, and reducing the conflict factors such as bus stops in green spaces are determined to be important.