• 한국자동차공학회논문집
• /
• 제12권6호
• /
• pp.111-118
• /
• 2004

The work presented in this paper concerns the aerodynamic characteristics and compression wave generated in a tunnel when a high speed train enters it. A large number of solutions have been proposed to reduce the amplitude of the pressure gradient in tunnels and some of the most efficient solutions consist of (a) addition ofa blind hood, (b) addition of inclined part at the entrance, and (c) holes in the ceiling of the tunnel. These are numerically studied by using the three-dimensional unsteady compressible Euler equation solver with ALE, CFD code, based on FEM method. Computational results showed that the smaller inclined angle leads to the lower pressure gradient of compression wave front. This study indicated that the most efficient slant angle is in the range from $30^{\circ}$ to $50^{\circ}$. The maximum pressure gradient is reduced by $26.81\%$ for the inclined angle of $30^{\circ}$ as compared to vertical entry. Results also showed that maximum pressure gradient can be reduced by $15.94\%$ in blind hood entry as compared to $30^{\circ}$ inclined tunnel entry. Furthermore, the present analysis showed that inclined slant angle has little effect on aerodynamic drag. Comparison of the pressure gradient between the inclined tunnel hood and the vertical entry with air vent holes indicated that the optimum inclined tunnel hood is much more effective way in reducing pressure gradient and increasing the pressure rise time.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2009년 춘계학술대회논문집
• /
• pp.191-195
• /
• 2009

A parametric study for for the water entry of a two dimensional symmetric wedge with deadrise angle of 10 degrees was carried out to find out the most dominant parameter. Water entry problem with constant velocity is simplified as the stationary wedge in the way of the upcoming water surface. The calculated impact loads showed that the effect of the viscosity was not so important in this problem. For a given grid system a suitable time step size can be found. The most sensitive parameter was found to be the grid size.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제11권1호
• /
• pp.482-494
• /
• 2019

In this paper, the oblique water-entry impact of a vehicle with a disk cavitator is studied experimentally and numerically. The effectiveness and accuracy of the numerical simulation are verified quantitatively by the experiments in this paper and the data available in the literature. Then, the numerical model is used to simulate the hydrodynamic characteristics and flow patterns of the vehicle under different entry conditions, and the axial force is found to be an important parameter. The influences of entry angle, entry speed and cavitator area on the axial force are studied. The variation law of the force coefficient and the dimensionless penetration distance at the peak of the axial force are revealed. The research conclusions are beneficial to engineering calculations on the impact force of a vehicle with a disk cavitator over a wide range of water-entry parameters.

• Geomechanics and Engineering
• /
• 제13권2호
• /
• pp.195-215
• /
• 2017

This paper proposes gob-side entry retaining by roof break and filling in thick-layer soft rock conditions based on the thick-layer soft rock roof strata migration law and the demand for non-pillar gob-side entry retaining projects. The functional expressions of main roof subsidence are derived for three break roof direction conditions: lateral deflection toward the roadway, lateral deflection toward the gob and vertically to the roof. These are derived according to the load-bearing boundary conditions of the main roadway roof stratum. It is concluded that the break roof angle is an important factor influencing the stability of gob-side entry retaining surrounding rock. This paper studies the stress distribution characteristics and plastic damage scope of gob-side entry retaining integrated coal seams, as well as the roof strata migration law and the supporting stability of caving structure filled on the break roof layer at the break roof angles of $-5^{\circ}$, $0^{\circ}$, $5^{\circ}$, $10^{\circ}$ and $15^{\circ}$ are studied. The simulation results of numerical analysis indicate that, the stress concentration and plastic damage scope to the sides of gob-side entry retaining integrated coal at the break roof angle of $5^{\circ}$ are reduced and shearing stress concentration of the caving filling body has been eliminated. The disturbance of coal mining to the roadway roof and loss of carrying capacity are mitigated. Field tests have been carried out on air-return roadway 5203 with the break roof angle of $5^{\circ}$. The monitoring indicates that the break roof filling section and compaction section are located at 0-45 m and 45-75 m behind the working face, respectively. The section from 75-100 m tends to be stable.

• Design & Manufacturing
• /
• 제17권2호
• /
• pp.9-14
• /
• 2023

In this study, an experiment was conducted to confirm the applicability of the external shape control of the ultrasonic knife to the CFRTP material, which is the base material of thermoplastic. TC910 based on polyamide6 (PA6) was used as the material. The slope 와 and tool transfer speed of the material and tool were selected as process factors for processing, and the following results were obtained. Under all cutting conditions using an ultrasonic knife, friction heat caused by high-frequency vibration was issued at 150℃ at the contact part between the material and the knife during cutting. As a result of the cutting force analysis, the faster the transfer speed, the higher the cutting force as the angle of entry of the blade increased, and the size of the cutting force changed during cutting. As for the size of the burr in accordance with the transfer speed condition, the smallest burr occurred at 150mm/min in the side part, and the smallest burr occurred at 150mm/min and 200mm/min in the case of the outlet burr. The size of the burr according to the entry angle tended to decrease as the tool entry angle increased, and the side part tended to increase as the tool entry angle increased. As a result of the cutting surface analysis, it was confirmed that the base material was eluted under all conditions, and the faster the transfer speed, the lower the elution phenomenon of the base material. Based on the above results, cutting the CFRTP material with an ultrasonic knife is possible, but the effect on heat generation caused by friction needs to be minimized, and further research needs to be conducted on this.

• 한국항공우주학회지
• /
• 제30권7호
• /
• pp.51-60
• /
• 2002

통계학적 해석인 몬테-칼로 모의실험은 대기권 재진입 분산의 결과인 낙하예정지역뿐만 아니라 상태변수들의 최종조건들을 조사하는데도 사용된다. 본 논문에서 재진입 분산은 위도, 경도, 고도, 뱅크각, 비행경로각, 기수 오차, 그리고 항속거리로 생성되는 $7\times7$ 공분산 행렬로 한정된다. 감속을 목표로 하는 대기권 재진입시 이것들에 영향을 미치는 오차 원인들은 대기밀도, 온도, 초기오차, 바람, 그리고 항력계수의 추정오차 등에 관련된 불확실성들로서 이들 오차의 $3{\sigma}_n$와 공칭 비행궤적을 사용해서 상태변수의 공분산 행렬은 궤적 오차 해석을 수행함으로 결정될 수 있다. 재진입에 대한 몬테-칼로법의 적용에 있어서 주요 고려할 점은 교란궤적, 뱅크역전, 그리고 이 제적들 각각에 대한 최종 낙하지점의 결정이다. 본 논문은 불확실성에 대한 결과를 공력계수와 뱅크역전의 관점에서 해석한다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 Proceedings of the Korea Automatic Control Conference, 11th (KACC); Pohang, Korea; 24-26 Oct. 1996
• /
• pp.307-310
• /
• 1996

In this paper, we deal with some numerical analyses of a re-entry vehicle in a 2-dimensional plane as an optimal control problem. To reduce the dynamic load, the heat load and the oscillation in the trajectory, we researched the trajectories in which the load factor or the rate of flight path angle was minimized during re-entry. In addition to that, taking advantage of the monotonous subarc method and the folded time-axis method, we tried to find the heat-less and load-less trajectory with combinations of some sectional functionals so that we can achieve more comfortability.

• 한국군사과학기술학회지
• /
• 제20권4호
• /
• pp.467-473
• /
• 2017

In this paper, impact characteristics of a water entry gliding vehicle were analyzed using a finite element method. To guarantee the validity of analysis results, a convergence test was performed for several ratios of Euler and Largrange mesh sizes. The impact coefficient was calculated with respect to entry angles and angle of attacks. It can be observed that the impact coefficient was large at a high cross-section gradient and was also affected by cavitation. This study could be useful in the preliminary design stage of a water entry bomb development.

• 대한금속재료학회지
• /
• 제50권2호
• /
• pp.129-135
• /
• 2012

High speed casting technology is an attractive method to increase the productivity of continuous casting. However, high speed casting causes flow instability of molten steel in a mold. In this study, Large Eddy Simulation (LES) has been performed to identify the characteristics of mold flow for various shapes of submerged entry nozzles. The LES code has been newly developed to efficiently compute the two-phase flow by using the Fractional Step Method (FSM) combined with the Volume of Fluid (VOF) method. The Immersed Boundary Method was used to implement the shape of the submerged entry nozzle. Three cases of discharge angle of the submerged entry nozzle were computed and compared. The current results shed light on improving shape design of a submerged entry nozzle.

• 한국분무공학회지
• /
• 제9권1호
• /
• pp.21-29
• /
• 2004

The flow characteristics of a swirl injector were investigated with the variation of the flow condition and geometric dimensions, such as orifice length for considering the viscous effect and tangential entry port area for considering the swirl intensity. The liquid film thickness strongly influencing on the formed drop size of the spray was measured using a new technique. The film thickness measurement technique proposed here, used the attenuation of fluorescence signal near the injector exit. The breakup length that is important for the flame location as well as the spray cone angle which influences on the ignition performance was measured using a backlit stroboscopic photography technique. From the experimental results, it is found that an increase in injection pressure decreased the film thickness and breakup length, and also enlarged the spray cone angle. A decrease in orifice length and tangential entry port area has a similar tendency of thinner film thickness, shorter breakup length and larger spray cone angle. In the present study, we proposed empirical models of the flow characteristics of the swirl injectors.