• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.4
• /
• pp.909-916
• /
• 2015

Recently, as shown demands and the need for Cloud dig data, large-scale data centers, as well as factory unit's have also vigor. This study focuses the system design that can integrate various facilities on the data center build upon of the factory and the midsize group. Because the integrated facilities management of midsize groups should have variety of sensors and devices requires integrated monitoring system that can manage them as a whole. In this study, it constitutes a integrated model protocol interface of the various facilities, it suggests ways to avoid the errors that may occur during design to study the development and systematically carried out. For this purpose, this study provides the analysis of a failure information delivery time and integration scenario for efficient analysis and evaluation of an integrated monitoring system.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.12
• /
• pp.1025-1031
• /
• 2012

The present paper deals with concept design of supersonic inlet based on compressible flow theory and flow control of bleeding in order to guarantee stability of supersonic inlet of ramjet engine in broad range of operating conditions. Shock instability, shock wave-boundary layer interaction and flow separation should be properly controlled to improve performance of the supersonic inlet. Considering shock strength, boundary layer and flow separation, the supersonic inlet is modified from the basic model which is designed under inviscid theory. Consequently, shock is stabilized, and required mass flow rate is obtained. Furthermore, bleeding is applied to the supersonic inlet to maintain performance in off-design conditions. Mass flow condition is adopted for modeling of bleeding effect, and performance of the supersonic inlet is evaluated by changing bleeding locations and numbers.

• Journal of Power System Engineering
• /
• v.21 no.3
• /
• pp.37-44
• /
• 2017

In this study, failure analysis of the angular pin for molding machines to aluminum component molding was carried out. SM45C steel was used for the angular pin, it was surface hardened by the induction surface hardening heat treatment. The cross section of damaged angular pin was observed, and micro Vickers hardness value from the fractured part was measured. Brittle fracture was occurred from the fracture surface of angular pin, therefore, impact toughness value was evaluated by V-notch Charpy impact test. It was confirmed that the impact absorption energy was high when was tempered at a high temperature for a long time, and the toughness was slightly increased. Also, 2-parameter Weibull statistical analysis was investigated in order to evaluate the reliability of the measured micro Vickers hardness values and absorbed energy. The micro Vickers hardness and absorbed energy well followed a two-parameter Weibull probability distribution, respectively. The reverse design against angular pin was proposed as possible by using test results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.12
• /
• pp.1212-1218
• /
• 2014

This paper proposes a planar bow-tie UWB antenna by modifying the ground patch of a reference bowtie-monopole antenna satisfying low band of UWB. The proposed antenna was implemented with five-angled ground patch to be operated in whole UWB band, while the reference antenna had a ground patch of half circle type. The measured return loss satisfies less than -10 dB in 3.1~10.6 GHz, except 4.9~5.8 GHz rejection band. The measured radiation pattern is almost the same with that of the monopole antenna. The radiation gain reduction is about 8 dB at rejection band.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.33 no.4
• /
• pp.209-216
• /
• 2020

In this paper, parametric structural analysis is presented utilizing the co-rotational(CR) shell analysis utilizing EDISON. CR shell analysis shows faster convergence than the commercial software, NASTRAN, does. The 1st natural frequency of the rear frame is obtained, which is close to that of the engine during high speed cruise. Three cases under two design variables are presented and analyzed. Gusset is shown to be more effective among those which feature the same weight change. The results presented in this paper will be applicable for further researches to improve the durability of a motorcycle rear frame.

• Journal of Power System Engineering
• /
• v.18 no.5
• /
• pp.80-87
• /
• 2014

The pipelines are apt to erosion or corrosion because of the high-speed flow of water and steam with high temperatures or high pressures. This study was carried out a finite element analysis (FEA) and an experimental for the fracture behavior of T-joint pipes with local wall thinning under internal pressure. Local wall thinning was machined on the pipes in order to simulate erosion and corrosion of the metal. The configurations of the eroded area included an eroded ratio of d/t=0.80~0.963 and an eroded length of l=25 mm, 50 mm, and 102 mm. Three-dimensional elastic-plastic analyses were also carried out using FEA, which accurately simulates failure behaviors. In regards to the relationship between pressure and eroded, the criterion that indicates what can be used safely under operating pressure and design pressure were obtained from FEA. The FEA results were in relatively good agreement with that of the experiment.

• Journal of Power System Engineering
• /
• v.18 no.5
• /
• pp.66-73
• /
• 2014

This study was considered to occur the local wall thinning at elbow which is flowing the steam and high-pressure water of high-temperature. The angle of elbow is ${\Theta}=45^{\circ}$ and $67.545^{\circ}$. The damage behaviors of inner or outer wall thinning elbow under internal pressure were calculated by FEA(finite element analysis). We compared the simulated results by FEA with experimental data. The FEA results are as follows: In the FEA results of three types of wall thinning ratio, the circumferential and longitudinal stresses show the similar values regardless of the angle of elbow, respectively. The circumferential strain was greater at elbow of small angle, but the longitudinal strain was nearly same. The FEM stress of outer wall thinning elbow was slightly higher than that of the inner wall thinning elbow, and strain was also slightly higher. In the experiments, the circumferential strain was increased with the increase in the internal pressure, and increased rapidly on about 0.2% of strain. The longitudinal strain was small. The strain at break was much smaller than 0.2%. In the relation between pressure and eroded ratio, the criteria that can be used safely under operating pressure and design pressure were obtained. The results of FEA were in relatively good agreement with those of the experiment.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2005.05a
• /
• pp.321-324
• /
• 2005

기존의 LMS(Learning Management System)는 웹 기반의 e-Learning 교육의 장점에도 불구하고 학습자의 요구와 수준에 무관하게 학습과 관련한 컨텐츠들이 획일적으로 구성됨으로써, 학습자의 요구를 만족시키지 못하고 있다. 본 논문에서는 LCMS(Learning Content Management System) 와 LMS를 연계한 학습 통계 모듈을 제시하고, LMS에 학습자와 운영자에게 학습정보 데이터를 제공함으로써 학습하는 과정을 추적하고 학습이력을 관리 할 수 있는 학습통계모듈을 설계하고 구현한다. 제시된 모듈에서는 효과적인 학습통계을 위한 검색 방안으로 LCMS의 메타데이터와 다양한 학습관리 정보(CMI)값을 LMS를 호출하는 기능인 API(Application Program Interface) 어댑터를 이용하여 연계된 값과 LMS시스템에 학습지원과 운영지원 기능을 추가하여 나온 결과값을 바탕으로 하였다. 이 학습통계모듈을 통해서 LMS운영자는 학습자의 컨텐츠의 활용을 더욱 확장할 수가 있으며 학습자의 학습정보관리를 하는 LMS의 성능을 향상 시키고자 하였다.

• Proceedings of the Korean Information Science Society Conference
• /
• 2007.06b
• /
• pp.15-20
• /
• 2007

기존의 연구는 DNA 커널을 통한 기계 학습이 DNA 분자들을 통한 in vitro 실험을 통해 가능함을 보였다. 이 때, DNA 커널을 통한 분류 분제는 온도 조절을 통해 양한정(positive definite) 조건을 만족시킬 때 분류 문제를 잘 풀며, 양한정 조건을 만족시키기 위한 조건으로 높은 온도에서 시작하여 온도를 내리며 hybridization시키는 방법을 제안하였다. 이 논문에서는 보다 정량적인 분석을 통해서 이 hybridization 방법이 양한정 조건을 만족시키기에 적합한 방법임을 보이고, 간단한 hybridization 모델을 통해 양한정 조건을 만족시킬 수 있는 hybridization 온도 계획의 충분 조건을 유도한다. 또한 시작 온도와 끝 온도의 경계 조건으로 제시되는 이 충분 조건을 통해 현실적인 온도 조절 계획을 위한 시퀀스의 코딩 방법을 알게 된다.

• Korean Chemical Engineering Research
• /
• v.52 no.6
• /
• pp.834-839
• /
• 2014

This study was conducted to optimize the medium composition for carotenoid production in Arthrobacter sp. PAMC 25486 through response surface methodology (RSM). Using a Placket-Burman design, from which yeast extract, $MgSO_4$ and dextrose were identified as the significant factors affecting carotenoids production. RSM studies for carotenoids production by Arthrobacter sp. PAMC 25486 have been carried out for three parameters of yeast extract, $MgSO_4$ and dextrose concentrations. These significant factors were optimized by experiments and RSM, as 1 g/L yeast extract, 0.0879 g/L $MgSO_4$ and 1 g/L dextrose. The experimentally obtained concentration of carotenoid was 288 mg/L, and it became 2-fold increase on concentration before optimization.