• Journal of Biomedical Engineering Research
• /
• v.24 no.5
• /
• pp.401-410
• /
• 2003

This study investigates the biomechanical efficacies of various cement augmentation techniques with or without pressurization for varying degrees of osteoporotic femur. For this study, a biomechanical analysis using a finite element method (FEM) was undertaken to evaluate surgical procedures, Simulated models include the non-cemented(i.e., hip screw only, Type I), the cement-augmented(Type II), and the cemented augmented with pressurization(Type III) models. To simulate the fracture plane and other interfacial regions, 3-D contact elements were used with appropriate friction coefficients. Material properties of the cancellous bone were varied to accommodate varying degrees of osteoporosis(Singh indices, II∼V). For each model. the following items were analyzed to investigate the effect surgical procedures in relation to osteoporosis of varying degrees : (a) von Mises stress distribution within the femoral head in terms of volumetric percentages. (b) Peak von Mises stress(PVMS) within the femoral head and the surgical constructs. (c) Maximum von Mises strain(MVMS) within the femoral head, (d) micromotions at the fracture plane and at the interfacial region between surgical construct and surrounding bone. Type III showed the lowest PVMS and MVMS at the cancellous bone near the bone-construct interface regardless of bone densities. an indication of its least likelihood of construct loosening due to failure of the host bone. Particularly, its efficacy was more prominent when the bone density level was low. Micromotions at the interfacial surgical construct was lowest in Type III. followed by Type I and Type II. They were about 15-20% of other types. which suggested that pressurization was most effective in limiting the interfacial motion. Our results demonstrated the cement augmentation with hip screw could be more effective when used with pressurization technique for the treatment of intertrochanteric fractures. For patients with low bone density. its effectiveness can be more pronounced in limiting construct loosening and promoting bone union.

• The Journal of Engineering Geology
• /
• v.22 no.4
• /
• pp.387-398
• /
• 2012

Korean agricultural areas that employ water curtain cultivation (WCC) have recently suffered extensive groundwater shortages due to an increase in the number of facilities. The primary focus of this study is to measure the daily groundwater use and discharge rates in the Cheongweon and Chungju pilot areas, while the second focus is to estimate the total amount of groundwater used in WCC areas nationwide in Korea. Taking into consideration several factors, including motor type, outflow abilities of wells, records of daily minimum temperatures below $0^{\circ}C$, and the number of running wells according to weather variations, we estimated that $53,138m^3/ha$ of groundwater had been used in the 4-hectare Cheongweon pilot area during the winter period of late 2011 through early 2012. On a prorated areal basis, we can calculate that the total groundwater used nationwide was 0.57 billion $m^3$ in WCC areas of $10,746m^2$. This value is equivalent to 33.7% of the total agricultural groundwater use (1.69 billion $m^3$) in Korea. During 9-22 February 2012, the daily water discharge rate in the 4-ha Cheongweon pilot area ranged from 2,079 to $2,628m^3$, averaging $2,341m^3$. Combining this value with meteorological records for 94 days with a daily minimum temperature below $0^{\circ}C$ results in an estimated groundwater volume of $54,990m^3/ha$ for the pilot area during the 2011-2012 winter period. The total amount of groundwater used nationwide in WCC areas would then be 0.59 billion $m^3$, equivalent to 34.9% of the total agricultural groundwater use in Korea. In the Chungju area, the groundwater discharge rate was estimated to be less than 805 $m^3$/ha. This value, combined with weather data for 108 days with a daily minimum temperature below $0^{\circ}C$ in this area, can be applied to infer that the total groundwater volume used in WCC areas nationwide is no more than 55% of the total agricultural groundwater use in Korea.

• Journal of Engineering Education Research
• /
• v.12 no.1
• /
• pp.3-16
• /
• 2009

The purpose of this study is to prepare diverse measures to enhance the utilization of national authorized qualification. The detail objectives of this study are first, to re-establish the utilization scope and range of national authorized qualification through analysis of advance research and theory in various fields of learning on the function of qualification; and second, to set the direction to strengthen the utilization of national authorized qualification. Based on discussions on the various fields of learning on the function of qualification, this study divided the utilization scope of qualification into personal utilization for the benefit of the qualification acquirer him or herself and public utilization for the social and economic benefits. And according to this distinction, we prepared measures to strengthen the utilization of national authorized qualification. First of all, as a way to strengthen personal utilization of the national authorized qualification, we prepared measures to enhance accessibility and facilitate further improvement. As a means to enhance accessibility, we proposed restriction on setting the application condition, diversification of qualification authorization method, facilitation of partial qualification system and minimization of expense required to acquire qualification. Also for the further improvement, we proposed creation of job-level centered grade system and development of job-level centered qualification item by stage. For strengthening the public utilization of national authorized qualification, we come up with ways of strengthening flexibility, transparency, public trust and compatibility. As a way to strengthen flexibility, we proposed establishment of qualification demand monitoring system, expansion of direct participation of users on qualification management, establishment of qualification expiration period and its renewal. For the strengthening of transparency, we proposed to build general qualification information system and to utilize qualification recommendation system. To strengthen public trust, we proposed to strengthen the management of qualification management regulation, secure independency, establish internal audit system and strengthen post management of national authorized qualification. And lastly, we suggested that compatibility comparison standard between qualification and qualification level standard be developed for the strengthening of compatibility.

• Journal of Internet Computing and Services
• /
• v.16 no.1
• /
• pp.57-65
• /
• 2015

As information technology fusion is accelerated, the researches to improve the quality and productivity of crops inside a plant factory actively progress. Advanced growth environment management technology that can provide thermal environment and air flow suited to the growth of crops and considering the characteristics inside a facility is necessary to maximize productivity inside a plant factory. Currently running plant factories are designed to rely on experience or personal judgment; hence, design and operation technology specific to plant factories are not established, inherently producing problems such as uneven crop production due to the deviation of temperature and air flow and additional increases in energy consumption after prolonged cultivation. The optimization process has to be set up in advance for the arrangement of air flow devices and operation technology using computational fluid dynamics (CFD) during the design stage of a facility for plant factories to resolve the problems. In this study, the optimum arrangement and air flow of air circulation fans were investigated to save energy while minimizing temperature deviation at each point inside a plant factory using CFD. The condition for simulation was categorized into a total of 12 types according to installation location, quantity, and air flow changes in air circulation fans. Also, the variables of boundary conditions for simulation were set in the same level. The analysis results for each case showed that an average temperature of 296.33K matching with a set temperature and average air flow velocity of 0.51m/s suiting plant growth were well-maintained under Case 4 condition wherein two sets of air circulation fans were installed at the upper part of plant cultivation beds. Further, control of air circulation fan set under Case D yielded the most excellent results from Case D-3 conditions wherein air velocity at the outlet was adjusted to 2.9m/s.

• Journal of Food Hygiene and Safety
• /
• v.25 no.4
• /
• pp.367-375
• /
• 2010

The bacteriological and physiochemical analysis of sea water and sediments in Tongyeong harbor was conducted to evaluate sanitary conditions. The samples were collected at 8 stations established once a month from June, 2008 to May, 2009. During the study period, the range of temperature was from 6.7 to $25.2^{\circ}C$, transparency ranged from 1.2 to 2.6 m, chemical oxygen demand ranged from 1.90 to 2.92 mg/L, dissolved oxygen ranged from 6.2 to 10.5 mg/L, dissolved nitrogen ranged from 0.052 to 0.098 mg/L, phosphate ranged from 0.044 to 0.065 mg/L, respectively. Seafood, if eaten raw, carries the risk of food poisoning. Seafood poisoning is often cause by pathogenic microorganism originating from fecal contamination, such as Salmonella sp., Shigella sp. and norovirus. Fecal coliforms are an important indicator of fecal contamination. Therefore, data on fecal coliform are very important for evaluating the safety of fisheries in coastal areas. So, we investigated the sanitary indicate bacteria. The coliform group and fecal coliform MPN's of sea water in Tongyeong harbor were ranged from < 1.8~22,000/100 mL (GM 164.9 MPN/100 mL) and < 1.8~7,900 MPN/100 mL (GM 33.7 MPN/100 mL), respectively. Total coliform were detected 97.0% in 96 of samples and 68.9% of total coliforms were fecal coliforms. These results similar to another seawater detection ratio of total coloforms and fecal coliforms. The Vibrios was isolated and identified with VITEK system. Four hundred eighty strains that were obtained from sea water samples in Tongyeong harbor Detection ratio Vibrio alginolyticus, 34.2%, Vibrio parahaemolyticus, 13.8%, Vibrio vulnificus 10.0%, and V. mimicus 12.5% respectively. Vibrio cholerae O1, was not detected. During the study period, the ranges of water content, ignition loss, COD, and acid volatile sulfates in sediments in Tongyeoung harbor were 41.0~57.4%, 7.8~10.5%, 6.51~9.30 mg/g, 0.04~0.09 mg/g, respectively. Heavy metals in sediment of Tongyeoung harbor were Cd, $0.10{\pm}0.05$; Cu, $4.79{\pm}8.20$; As, $1.95{\pm}0.17$; Hg, $0.10{\pm}0.07$; $Cr^{6+}$, $0.34{\pm}0.12$; Zn, $125.33{\pm}16.40$; Ni, $16.43{\pm}1.93$ mg/kg.

• Journal of Biomedical Engineering Research
• /
• v.23 no.1
• /
• pp.49-60
• /
• 2002

Receive dynamic focusing with an array transducer can provide near optimum resolution only in the vicinity of transmit focal depth. A customary method to increase the depth of field is to combine several beams with different focal depths, with an accompanying decrease in the frame rate. In this Paper. we Present a simultaneous multiple transmit focusing method in which chirp signals focused at different depths are transmitted at the same time. These chirp signals are mutually orthogonal in a sense that the autocorrelation function of each signal has a narrow mainlobe width and low sidelobe levels. and the crossorelation function of any Pair of the signals has values smaller than the sidelobe levels of each autocorrelation function. This means that each chirp signal can be separated from the combined received signals and compressed into a short pulse. which is then individually focused on a separate receive beamformer. Next. the individually focused beams are combined to form a frame of image. Theoretically, any two chirp signals defined over two nonoverlapped frequency bands are mutually orthogonal In the present work. however, a tractional overlap of adjacent frequency bands is permitted to design more chirp signals within a given transducer bandwidth. The elevation of the rosscorrelation values due to the frequency overlap could be reduced by alternating the direction of frequency sweep of the adjacent chirp signals We also observe that the Proposed method provides better images when the low frequency chirp is focused at a near Point and the high frequency chirp at a far point along the depth. better lateral resolution is obtained at the far field with reasonable SNR due to the SNR gain in Pulse compression Imaging .

• Journal of Biomedical Engineering Research
• /
• v.25 no.5
• /
• pp.403-414
• /
• 2004

In the accompanying paper, we proposed a real. time volumetric imaging method using a cross array based on receive dynamic focusing and synthetic aperture focusing along lateral and elevational directions, respetively. But synthetic aperture methods using spherical waves are subject to beam spreading with increasing depth due to the wave diffraction phenomenon. Moreover, since the proposed method uses only one element for each transmission, it has a limited transmit power. To overcome these limitations, we propose a new real. time volumetric imaging method using cross arrays based on synthetic aperture technique with linear wave fronts. In the proposed method, linear wave fronts having different angles on the horizontal plane is transmitted successively from all transmit array elements. On receive, by employing the conventional dynamic focusing and synthetic aperture methods along lateral and elevational directions, respectively, ultrasound waves can be focused effectively at all imaging points. Mathematical analysis and computer simulation results show that the proposed method can provide uniform elevational resolution over a large depth of field. Especially, since the new method can construct a volume image with a limited number of transmit receive events using a full transmit aperture, it is suitable for real-time 3D imaging with high transmit power and volume rate.

• Applied Chemistry for Engineering
• /
• v.28 no.1
• /
• pp.101-111
• /
• 2017

Mineral carbonation is a technology in which carbonates are synthesized from minerals including serpentine and olivine, and industrial wastes such as slag and cement, of which all contain calcium or magnesium when reacted with carbon dioxide. This study aims to develop the mineral carbonation technology for commercialization, which can reduce environmental burden and process cost through the reduction of carbon dioxide using steel slag and the slag reuse after calcium extraction. Calcium extraction was conducted using NH4Cl solution for air-cooled slag and convert slag, and ${\geq}98%$ purity calcium carbonate was synthesized by reaction with calcium-extracted solution and carbon dioxide. And we conducted experimentally to minimize the quantity of by-product, the slag residue after calcium extraction, which has occupied large amount of weight ratio (about 80-90%) at the point of mineral carbonation process using slag. The slag residue was used to replace silica sand in the manufacture of cement panel, and physical properties including compressive strength and flexible strength of panel using the slag residue and normal cement panel, respectively, were analyzed. The calcium concentration in extraction solution was analyzed by inductively coupled plasma optical emission spectrometer (ICP-OES). Field-emission scanning electron microscope (FE-SEM) was also used to identify the surface morphology of calcium carbonate, and XRD was used to analyze the crystallinity and the quantitative analysis of calcium carbonate. In addition, the cement panel evaluation was carried out according to KS L ISO 679, and the compressive strength and flexural strength of the panels were measured.

• Journal of the Korean Geographical Society
• /
• v.41 no.2 s.113
• /
• pp.212-226
• /
• 2006

Surface data generally represent continuous distribution of geographical or social phenomena of a region in urban analysis. Instances include distribution of temperature, population of region, and various distributions related to human activities. When spatial data are given in the form of surface, surface comparison is required as a way of comprehending the surface change or the relationship between two surfaces. As for previous approaches of surface comparison, there are visualization, quantitative methods and qualitative method. All those approaches, however, show the difference between two surfaces in a limited way. Especially, they are not able to distinguish spatial difference between two surfaces. To overcome such problem, this paper proposes a method of comparing two surfaces in terms of their spatial structure. Main concept of the method comes from earth moving problem and the method is named minimum surface transformation, here. When a surface is transformed into another, total surface volume moved in the process of transformation should be the minimum. Both quantitative and spatial differences between two surfaces are evaluted by total surface volume moved and the distribution of moved surface volume of each cell respectively. The method is applied to hypothetical and actual data. From the former, it is understood that the method explains how two surfaces are quantitatively and spatially different. The result of the latter shows that moved total surface volume decreases as time goes by which fits the actual situation that population change rate gets smaller. Concerning the other measure of surface difference, the distribution of $X_{ij}$ describes detailed flow of surface volume than that of simply subtracting surface volume by indicating to what direction the population change occurs.

• The korean journal of orthodontics
• /
• v.40 no.5
• /
• pp.294-303
• /
• 2010

Objective: This study was designed to measure the surface roughness at the slot floor of various ceramic brackets. Methods: One kind of stainless steel bracket ($Succes^{(R)}$), two kinds of monocrystalline brackets (Inspire $Ice^{(R)}$, $Perfect^{(R)}$) and two kinds of polycrystalline brackets (Crystalline $V^{(R)}$, $Invu^{(R)}$) were examined. Atomic force microscopy (AFM) was used to measure the surface roughness of each bracket. Data acquisition and processing were performed using $SPIP^{TM}$. Results: The differences in values of Sa, Sq, and Sz in $Invu^{(R)}$ and Inspire $Ice^{(R)}$ were not statistically different from the control group $Succes^{(R)}$. The values of Sa, Sq, and Sz of $Perfect^{(R)}$ and Crystalline $V^{(R)}$ were greater than those of $Succes^{(R)}$. Differences of all the Sa, Sq, and Sz values between $Perfect^{(R)}$ and Crystalline $V^{(R)}$ were not statistically significant. Conclusions: It is concluded that the slot surfaces of $Succes^{(R)}$, Inspire $Ice^{(R)}$, and $Invu^{(R)}$ were smooth compared to those of Crystalline $V^{(R)}$ and $Perfect^{(R)}$.