• Korean Journal of Environmental Biology
• /
• v.36 no.1
• /
• pp.73-81
• /
• 2018

This study was conducted to understand the current status of the translocated species using a precede study and a model to evaluate the potential invasiveness that could adversely affect the aquatic ecosystem in the Gangneungnamdae Stream. A total of 12 translocated species were investigated and identified from 9 sites in a precede study, and steadily increased since 1982. For the study, which utilized research based on the total FISK (Fish Invasivenss Screening Kit) scores, all of the non-native fishes in Gangneungnamdae Stream were classified into two groups: namely as a high and a medium risk of becoming invasive. It was determined that there were two species (Zacco platypus and Pseudorasbora parva) that were determined to have posed the highest risk. The study determined that the mean scores were shown to have ranged from $3.06({\pm}0.16)-3.42({\pm}0.13)$. Consequently, the habitat analysis showed that the determined QHEI (Qualitative Habitat Evaluation Index) values in the stream averaged 146 (88-171), indicating that an optimal habitat condition did exist in that locale. It can be inferred that compared to land use in the surrounding watersheds, the QHEI values and frequency of translocated species showed the lower the altitude of stream, the QHEI values were decreased and in case of land use pattern, a noted decreased forest and grassland area, and gradually increased urbanized area was seen to exist in the region. The correlation between the fish assemblage, QHEI, land use pattern of surrounding watershed and number of translocated species was identified and analyzed when the stream altitude decreased, and the number of species was increased (r= - 0.782, p=0.0127), the number of species was decreased (r= - 0.737, p=0.0234), and finally when the QHEI values were decreased, it was noted that the urbanized area was increased (r=0.292, p=0.446). In the case of the number of translocated species, when the number of translocated species was increased, the associated urbanized area was increased.

• The Journal of Engineering Geology
• /
• v.15 no.2 s.42
• /
• pp.213-227
• /
• 2005

This study aims to assess the problems with investigation method and to suggest the complementary solutions by comparing the predicted data from surface investigation with the outcome data from underground cavern. In the study area, one(NE-1) of 6 fracture zones predicted during the surface investigation was only confirmed in underground caverns. Therefore, it is necessary to improve the confidence level for prediction. In this study, the fracture classification criteria was quantitatively suggested on the basis of the BHTV images of NE-1 fracture zone. The major orientation of background fractures in rock mass was changed at the depth of the storage cavern, the length and intensity were decreased. These characteristics result in the deviation of predieted predicted fracture properties and generate the investigation bias depending on the bore hole directions and investigated scales. The evaluation of hydraulic connectivity in the surface investigation stage needs to be analyze by the groundwater pressures and hydrochemical properties from the monitoring bore hole(s) equipped with a double completion or multi-packer system during the test bore hole is pumping or injecting. The hydraulic conductivities in geometric mean measured in the underground caverns are 2-3 times lower than those from the surface and furthermore the horizontal hydraulic conductivity in geometric mean is six times lower than the vertical one. To improve confidence level of the hydraulic conductivity, the orientation of test hole should be considered during the analysis of the hydraulic conductivity and the methodology of hydro-testing and interpretation should be based on the characteristics of rock mass and investigation purposes.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.11 no.4
• /
• pp.181-190
• /
• 2008

To response climate change and Kyoto protocol and to reduce greenhouse gas emissions, marine geological storage of $CO_2$ is regarded as one of the most promising option. Marine geological storage of $CO_2$ is to capture $CO_2$ from major point sources(eg. power plant), to transport to the storage sites and to store $CO_2$ into the marine geological structure such as deep sea saline aquifer. To design a reliable $CO_2$ marine geological storage system, it is necessary to perform numerical process simulation using thermodynamic equation of state. The purpose of this paper is to compare and analyse the relevant equations of state including ideal, BWRS, PR, PRBM and SRK equation of state. To evaluate the predictive accuracy of the equation of the state, we compared numerical calculation results with reference experimental data. Ideal and SRK equation of state did not predict the density behavior above $29.85^{\circ}C$, 60 bar. Especially, they showed maximum 100% error in supercritical state. BWRS equation of state did not predict the density behavior between $60{\sim}80\;bar$ and near critical temperature. On the other hand, PR and PRBM equation of state showed good predictive capability in supercritical state. Since the thermodynamic conditions of $CO_2$ reservoir sites correspond to supercritical state(above $31.1^{\circ}C$ and 73.9 bar), we conclude that it is recommended to use PR and PRBM equation of state in designing of $CO_2$ marine geological storage process.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.9 no.4
• /
• pp.125-134
• /
• 2001

The purpose of this study is to provide basic information for a future countermeasure municipal and to establish several wastes policy after investigating solid wastes from Sunchon City. In addition, this research can be supported to manage of recycling plant and to reuse plant of each wastes. Results are as bellows after checking up and analysis type of waste in Sunchon city Unit solid waste generation rate from single family is $0.50kg/person{\cdot}day$, and total solid wastes are 41.9ton/day. Unit solid waste generation rate from apartments is $0.45kg/person{\cdot}day$, and solid wastes generation is 55.5ton/day. Unit solid waste generation rate from agricultural is $0.22kg/person{\cdot}day$ and total solid wastes are 13.5ton/day. That show total amount of municipal solid wastes from residential are 110.9ton/day. Unit solid waste generation rate from traditional markets is $1.85kg/person{\cdot}day$, and solid waste total volume is 5,400kg/day. Unit solid waste generation rate from small store is $2.03kg/person{\cdot}day$, and solid waste total are 25,101kg/day. Therefore, this show that total wastes are 30.50kg from downtown and commercial area. Solid waste quantity from Industrial area (Factory region) is 8.5ton and in case of school and hospitals are 7.2kg/day and 3.0kg/day. Solid waste amount from Institutional is 6.6kg/day. Food wastes were eliminated from municipal solid wastes as standard 63.4ton/day, and combustible wastes were 126.9ton/day. If it schedule about 5 years (by 2006) as durable year for food wastes treatment plant, it is expected 42.5ton/day for treatment capacity. We can judge that it is effective to be set 2 lines equipment ${\times}25ton/day$ as treatment ability under considering unexpected working condition such as any repair, trouble and an electrical load. If it schedule about 10 years (by 2011) as durable year for food wastes treatment plant, it is expected 150 ton/day for treatment capacity. We can conclude that it is effective to be set 2 lines equipment ${\times}80ton/day$ as treatment ability under considering working condition such as low loaded operating and the repair for incineration.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.3
• /
• pp.375-388
• /
• 2017

In order to solve the traffic congest and environmental issues, small-cross section tunnel for small car only is increasing, but there is not standard for installation of disaster prevention facility. In this study, in order to investigate the behavioral characteristics of thermal environment and smoke in a small cross section tunnels with a large port exhaust ventilation system, the A86, the U-Smartway and the Seobu moterawy tunnel, Temperature and CO concentration in case of fire according to cross sectional area, heat release rate and exhaust air flow rate were analyzed by numerical analysis and the results were as follows. As the cross-sectional area of the tunnel decreases, the temperature of the fire zone increases and the rate of temperature rise is not significantly affected by heat release rate. However, there is a difference depending on the change of the exhaust air flow rate. In the case of applying the exhaust air flow rate $Q_3+2.5Ar$ of the large port exhaust ventilation system, the temperature of the fire zone was 7.1 times for A86 ($Ar=25.3m^2$) and 5.4 time for U-smartway ($Ar=37.32m^2$) by Seobu moterway tunnel ($Ar=46.67m^2$). The CO concentration of fire zone also showed the same tendency. The A86 tunnels were 10.7 times and the U-Smartways were 9.5 times more than the Seobu moterway. Therefore, in the case of a small section tunnel, the thermal environment and noxious gas concentration due to the reduction of the cross-sectional area are expected to increase significantly more than the cross-sectional reduction rate.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.4
• /
• pp.223-231
• /
• 2012

The purpose of this study is to investigate basically the mechanism of heat transfer by the resolution of complex fluid flow inside a sophisticated designed screw dryer for the treatment of sewage sludge by using numerical analysis and experimental study. By doing this, the result was quite helpful to obtain the design criteria for enhancing drying efficiency, thereby achieving the optimal design of a multiple screw type dryer for treating inorganic and organic sludge wastes. One notable design feature of the dryer was to bypass a certain of fraction of the hot combustion gases into the bottom of the screw cylinder, by the fluid flow induction, across the delicately designed holes on the screw surface to agitate internally the sticky sludges. This offers many benefits not only in the enhancement of thermal efficiency even for the high viscosity material but also greater flexibility in the application of system design and operation. However, one careful precaution was made in operation in that when distributing the hot flue gas over the lump of sludge for internal agitation not to make any pore blocking and to avoid too much pressure drop caused by inertial resistance across the lump of sludge. The optimal retention time for rotating the screw at 1 rpm in order to treat 200 kg/hr of sewage sludge was determined empirically about 100 minutes. The corresponding optimal heat source was found to be 150,000 kcal/hr. A series of numerical calculation is performed to resolve flow characteristics in order to assist in the system design as function of important system and operational variables. The numerical calculation is successfully evaluated against experimental temperature profile and flow field characteristics. In general, the calculation results are physically reasonable and consistent in parametric study. In further studies, more quantitative data analyses such as pressure drop across the type and loading of drying sludge will be made for the system evaluation in experiment and calculation.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.9
• /
• pp.939-947
• /
• 2008

PCR-DGGE method was applied to analyze changes of microbial community in simultaneous nitrification and denitrification (SND) bioreactor with various DO concentrations. In the analysis of eubacterial community, band profiles of DGGE were similar with 2 or 1 mg/L DO concentrations in the reactor. Experimental results led to 16 different bacteria being identified, including 5 dominant strains(3 strains of Uncultured Bacterium, 1 strains of Bacillus, 1 strains of Uncultured Bacteroidetes). DGGE results at 0.5 mg/L DO concentration led to 12 strains being identified, including 7 dominant strains(5 strains of Uncultured Bacterium, 2 strains of Zoogloea sp.). DGGE results at 0.1 mg/L DO concentration led to 11 strains being identified, including 3 dominant strains(1 strains of Uncultured Bacterium, 2 strains of Zoogloea sp.). In DGGE band profiles of $\beta$-AOB($\beta$-Ammonia Oxidizing Bacteria), only one band was observed. This band had 97% similarity with Nitrosomonas sp. done DNB Y20. This band was clearly observed at the 2, 1 and 0.5 mg/L DO concentrations, while the brightness of the band at 0.1 mg/L DO concentration was mostly dimmed. In DGGE band profiles of denitrification process, 5 bands(3 strains of Uncultured organism containing nirS, 2 strains of Uncultured organism containing nirK) were observed. Among those bands, the brightness of one band was gradually increased at the lower DO concentrations. This band has 86% identity with Uncultured organism clone eS1 cd1 nirS gene, partial cds. Based on this result, it could be concluded that Uncultured organism clone eS1 cd1 nirS gene, partial cds is a predominant microorganism in the denitrification process.

• Journal of Bio-Environment Control
• /
• v.16 no.3
• /
• pp.210-216
• /
• 2007

A study was conducted to find mechanism and spray characteristics of a mini-sprinkler with downward spray to develop a new design type to be able to prevent drop water. The experiments were executed in a plastic greenhouse to minimize the effect of the wind. Data was collected at five different operation pressures and at 4 different raiser heights. Spray characteristics of the sprinkler such as effective radius, effective area, mean application depth, absolute maximum application depth, effective maximum application depth and coefficient of variation were determined. In order to analyze the mechanism and packing supporter of sprinkler, the numerical simulation using ABAQUS was performed. The optimum pressure for preventing drop water was determined.

• Current Research on Agriculture and Life Sciences
• /
• v.3
• /
• pp.28-35
• /
• 1985

This work Was carried out to obtain the most suitable crop coefficient for the paddy rice growing in Taegu area. The result was due to the comparative measurements of evapotranspiration formula in terms of Blaney & Criddle and eight other formulas with those produced by experiment particularly in this area. The crop coefficient, evapotranspiration and transpiration ratio produced by this research are hopefully expected to be of service in the future calculation of evapotranspiration without repeating experiment respectively, whenever the water requirement of paddy rice is planned in Taegu and its vicinity. The accomplished results could be summarized as follows : The maximum amount of evapotranspiration was recorded in the early and middle parts of August. The average reading of evapotranspiration was 6.33mm/day throughout the growth. The evapotranspiration had a highly significant correlation with pan evaporation, solar radiation, sunshine hours and relative humidity of meteorological elements. K and Kc by the use of Blaney & Criddle formula calculated at 0.76 to 1.45 and 0.82 to 1.27, respectively. Its peak value appeared commonly in early August. The ratio of transpiration was 269.03.

• Applied Biological Chemistry
• /
• v.48 no.1
• /
• pp.23-33
• /
• 2005

Agricultural sciences field in South Korea has many strong points such as numerous researchers, establishment of research infra-structure, excellence in research competitiveness and high technological level. However, there are also many weaknesses including insufficient leadership at related societies and institutes, deficiency of the next generation research group, and insufficiency in research productivity. There are many opportunities including increasing the importance of the biotechnological industry, activating international cooperation researches, and exploring the multitude of possible research areas to be studied. However, some threats still exist, such as pressure from the government of developed countries to open the agricultural market, the decrease of specialized farms, and intensification for researches to gratify economic and social demands. To encourage research activities in the agricultural sciences field in Korea, the following actions and systems are required: 1) formulation of a mid- and a long-term research master plan, 2) development of a database on the man power in related fields, 3) activation of top-down research topics, and associated increase of individual research grants, 4) development of special national programs for basic researches in agricultural sciences, 5) organization of a committee for policy and planning within the related societies, and 6) system development for the fair evaluation of the research results.