• Corrosion Science and Technology
• /
• v.14 no.4
• /
• pp.184-189
• /
• 2015

In this study, the combined effect of chloride and thiosulfate ions and the effect of the ratio of the two ions on passivation in 304L, 316L, and the duplex stainless steels 2101 and 2205 are investigated using potentiostatic scratch tests. Cyclic polarization and the scratch tests were used to understand the role of anions on localized corrosion in these systems. It was found that the thiosulfate pitting began at a lower potential for 2101 than 304L in 0.6 M NaCl + 0.03 M $Na_2S_2O_3$ solution. The pit morphologies for 304L, 316L, and 2101 in an 0.6 M NaCl + 0.03 M $Na_2S_2O_3$ solution were very different from each other. The results indicate that the pitting switches from predominately thiosulfate pitting to chloride pitting at approximately 0.1 V.

• Computational Structural Engineering
• /
• v.11 no.4
• /
• pp.147-154
• /
• 1998

강체 충격자가 납 표적에 33m/s ∼ 141m/s의 속도로 충돌할 때의 침투특성을 연구하기 위하여 Jognson 이론식을 이용한 이론해석과 AUTODYN 코드를 이용한 수치해석 및 실험장치를 이용한 실험측정을 실시하고 그 결과들을 비교 분석하였다. 실험장치로는 가스압력식 발사장치를 설계 제작하였으며, 실험용 충격자로는 충돌부위 형상이 반구형인 반구형 충격자와 원추형인 원추형 충격자 2종류를 사용하였다. 또한, 납재료에 대한 동적 유동응력을 얻기 위하여 홉킨스 압력봉실험을 수행하였다. 침투특성에 관한 연구결과, 이론적 해석결과는 저속 충돌범위(반구형 충격자 : 53m/s, 원추형 충격자 ; 73m/s)에서 실험결과치와 93%이상 잘 일치하였으며, 수치해석결과는 전체적인 충돌속도 범위에서 반구형 충격자인 경우 73%이상, 원추형 충격자인 경우 86%이상 일치하였다.

• Journal of the Korean Society of Systems Engineering
• /
• v.2 no.2
• /
• pp.39-44
• /
• 2006

With the advent of low cost, miniature and high-g hardened inertial sensors and actuators, many kind of smart munitions are becoming practical such as 1D or 2D TCM, SFM, Range Extended GPS guided munitions and so on. They have more complicated trajectory control algorithm than conventional munitions'. Therefore it is necessary to study the complicated operation algorithm of smart munitions with M&S in advance of developing them. The purpose of this paper is to introduce a practical M&S method to study an operation concept of smart munitions using PRODAS and Matlab.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.4
• /
• pp.377-383
• /
• 2005

This paper deals with the flow characteristics of air-water two-phase flow in a vertical tube of 10mm I.D. and 600mm in length at an adiabatic condition. The obtained experimental data were covered with the liquid superficial velocity ranging from 0.095m/s to 2.56m/s. and the gas superficial velocity ranging from 0.032m/s to 21.08m/s. The effects of the gas and liquid superficial velocity on the flow pattern transitions, frictional pressure drop, and film thickness and gas-liquid interface roughness were also examined. It was found that the film thickness increased and the liquid film wave length was more longer with the liquid superficial velocity $j_L$ increasing at $j_G$ constant. It was also showed that the frictional pressure drops were experienced in three regions. namely increasing region(bubbly flow), decreasing region (Taylor bubble and slug flows) and re-increasing region (annular flow).

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.10a
• /
• pp.155-155
• /
• 2009

The copper plating was deposited by pulse reverse current (PRC) method with additives. The all specimens were first immersted in 10% H2SO4 for 10 minutes, and then were rinsed with deionized water. The current densities of forward pulse were 400mA/$cm^2$, and those of reverse pulse were 1900mA/$cm^2$ and 100mA/$cm^2$. Results are compared for different additives for pulse plating conditions. When it added in Only CH4N2S (TU) or only C10H13NO3S (SVH), the effect of surface side growth of Cu was not different. But when it added in TU and SVH, surface side growth of Cu decreased. Polarization curves were measured from OCP to -0.7 V at a rate of 1mV/sec. Each specimen was observed under the PHENOM to see surface morphology.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.3
• /
• pp.627-633
• /
• 2013

An important problem in the transmission performance and efficiency is to find the values and the number of the cross-correlation function between two different maximal sequences. In this paper, we present the new maximal sequences which are obtained by the new decimations $d=\frac{2^{m-st-1}}{2^s-1}(2^n+2^{st+s+1}-2^{m+st+1}-1)$ from some maximal sequences. We will also find the values and the number of occurrences of each value of the cross-correlation function from the proposed decimations.

• Journal of Energy Engineering
• /
• v.16 no.3
• /
• pp.149-154
• /
• 2007

An experimental study on the air-side pressure drop of slit fin-tube heat exchanger has been carried out. The data reduction methodology for air-side pressure drop in the literature is not based on a consistent approach. This paper focuses on method of data reduction to obtain the air-side performance of fin-tube heat exchanger using R22 and recommends standard procedures for dry and wet surface pressure drop estimation in fin-tube heat exchanger. A comparison was made between the predictions of previously proposed empirical correlations and experimental data for the air-side pressure drop on design conditions of condenser and evaporator. Results are pre-sented as plots of friction f-factor against Reynolds number based on the fin collar outside diameter and compared with previous studies. The data covers a range of refrigerant mass fluxes of $150{\sim}250\;kg/m^2s$ with air flows at velocity ranges from 0.38 m/s to 1.6 m/s.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.4
• /
• pp.287-293
• /
• 2009

This study investigated the influence of ionic strength on the adhesion and release of bacteria (Escherichia coli, Bacillus subtilis, and Staphylococcus aureus) in quartz and iron-coated sands using column experiments. Results show that the mass recovery remained constant (E. coli = 13.7${\pm}$0.5%, B. subtilis = 9.8${\pm}$1.3%, S. aureus = 13.0${\pm}$2.1%) in iron-coated sand while it decreased from 80.7 to 45.3% (S. aureus) in quartz sand with increasing ionic concentrations from 1 to 100 mM. As the ionic concentrations of leaching solution was lowered from 100 to 0.1 mM, average 39.1% of bacterial detachment was quantified from quartz sand, but no bacterial release was observed in iron-coated sand. The phenomenon observed in iron-coated sand can be attributed to the inner-sphere complexes between bacteria and coated sand, which have minimal effect from ionic strength. This study improves our knowledge regarding the bacterial interaction with surface-modified porous media.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1994.10a
• /
• pp.312-316
• /
• 1994

본 연구를 통해 공간 푸리에변환을 이용한 반사계수측정에 있어서 L.S.B.M 및 유한크기 모델의 사용가능성과 유용성을 살펴보았다. 1) L.S.B.M은 P.D.M의 측정음압내에 포함되는 잡음에 대한 민감성을 줄일 수 있어 잡음에 대해 안정한 측정을 할 수 있는 장점이 있음을 알 수 있었다. 2) 유한크기모델은 무한크기모델의 경우 측정면적보다 큰 측정할 반사물질이 요구되는데 반해 측정할 물질의 크기에는 무관하게 반사계수를 얻을 수 있었고 이는 공간 푸리에 변환을 이용한 반사계수 측정방법의 유용성을 증가시킬 수 있다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.779-780
• /
• 2009