• Journal of Positioning, Navigation, and Timing
• /
• v.7 no.2
• /
• pp.73-90
• /
• 2018

Various navigation systems are integrated with the Global Navigation Satellite System (GNSS) to improve navigation performance so that continuous navigation information can be obtained even when navigation performance is degraded or navigation is not available due to the outage of GNSS. Time and cost can be reduced by evaluating performance of the integrated navigation system through Modeling and Simulation (M&S) software prior to the deployment of the integrated navigation system. The measurements of the navigation system should be generated to evaluate performance through of the navigation system M&S software. This paper proposes a method of designing a navigation environment generation module in M&S software of the integrated navigation system. To show applicability of the proposed method to M&S software design of the integrated navigation system, functions are verified through MATLAB. And then visual C++ based M&S software for the integrated navigation system is implemented to check the operation of the navigation environment generation module. The reference trajectory is generated and true measurements of Global Positioning System (GPS), Korea Positioning System (KPS), and enhanced Long range navigation (eLoran) are generated from the reference trajectory. The navigation results obtained from the true measurements are compared with the reference trajectories. The results show that the measurements generated using the design generation module by the proposed method are valid and the navigation environment generation module can be applied to M&S software of the integrated navigation system.

• Korean Journal of Chemical Engineering
• /
• v.35 no.11
• /
• pp.2256-2268
• /
• 2018

Hydrophilic and hydrophobic polyethersulfone (PES)-zinc oxide (ZnO) sublayers were prepared by loading of ZnO nanoparticles into PES matrix. Both porosity and hydrophilicity of the hydrophilic sublayer were increased upon addition of hydrophilic ZnO, while these were decreased for the hydrophobic sublayer. In addition, the results demonstrated that the hydrophilic membrane exhibited smaller structural parameter (S value or S parameter or S), which is beneficial for improving pure water permeability and decreasing mass transfer resistance. In contrast, a higher S parameter was obtained for the hydrophobic membrane. With a 2 M NaCl as DS and DI water as FS, the pure water flux of hydrophilic TFN0.5 membrane was increased from $21.02L/m^2h$ to $30.06L/m^2h$ and decreased for hydrophobic TFN0.5 membrane to $14.98L/m^2h$, while the salt flux of hydrophilic membrane increased from $10.12g/m^2h$ to $17.31g/m^2h$ and decreased for hydrophobic TFN0.5 membrane to $3.12g/m^2h$. The increment in pure water permeability can be ascribed to reduction in S parameter, which resulted in reduced internal concentration polarization (ICP). The current study provides a feasible and low cost procedure to decrease the ICP in FO processes.

• Korean Journal of Metals and Materials
• /
• v.49 no.8
• /
• pp.635-641
• /
• 2011

The effect of high shear speed on shear force, shear energy and fracture surface was investigated for the solder joint of a $Sn-_{3.0}Ag-_{0.5}Cu$ ball. For both ENIG and OSP pads, the shear force increased with an increase in shearing speed to 0.3 m/s. However, for an ENEPIG pad, the shear force increased with an increase in shear speed to 0.6 m/s and kept almost constant afterward. The shear energy decreased with an increase in shearing speed for ENIG and OSP pads. For the ENEPIG pad, however, the shear energy almost remained constant in a shearing speed range 0.3-3.0 m/s. The fracture mode analysis revealed that the amount of brittle fracture for the ENIG and the OSP pads increased with shearing speed, and a complete brittle fracture appeared at 1.0 m/s for ENIG and 2.0 m/s for OSP. However, the ENEPIG pad showed only a ductile fracture until 0.25 m/s, and a full brittle fracture didn't occur up to 3.0 m/s. The fracture mode matched well with the shear energy. The results from the high speed shear test of SAC305 were similar to those of SAC105.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.337-338
• /
• 2012

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.645-646
• /
• 2006

Pressure-induced decubitus is a serious disease among the elderly people. Interface pressure occluding vascular perfusion is known to be a cause of decubitus. Therefore, it is essential to quantify the relationship between vascular perfusion and interface pressure among the elderly people. Nine elderly normal people ($57.8{\pm}5.6\;years,\;63.3{\pm}7.0kg,\;1.68{\pm}0.05m$) were participated. Pressure was applied on the ischial tuberosity in the sitting posture from 0mmHg to 135mmHg as capillary vascular perfusion was recorded. The average interface pressure to occlude vascular perfusion under the ischial tuberosity is 120mmHg. Vascular perfusion values at the capillary occlusion is often lower than 60% of the vascular perfusion at 15mmHg. Higher sampling number is required to have more accurate results.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.6
• /
• pp.615-620
• /
• 1996

Chromium-Molybdenum steel was plasma-nitrided at 823 K for 10.8 ks in an atmosphere of 30% $N_2$-70% $H_2$ gas under 665 Pa without and with a subsidiary cathode of $MoS_2$ to compare ion-nitriding and plasma-sulfnitriding using subsidiary cathode. When the steel was ion-nitrided without $MoS_2$, iron nitride layer of 4$\mu\textrm{m}$ and nitrogen diffusion layer of 400mm were formed on the steel. A compound layer of 15$\mu\textrm{m}$ and nitrogen diffusion layer of 400$\mu\textrm{m}$ were formed on the surface of the steel plasma-sulfnitrided with subsidiary cathode of $MoS_2$. The compound layer consisted of FeS containing Mo and iron nitrides. The nitrides of $\varepsilon$-$Fe_2$, $_3N$ and $\gamma$-$Fe_4N$ formed under the FeS. The thicker compound layer was formed by plasma-sulfnitriding than ion-nitriding. In plasma-sulfnitriding, the surface hardness was about 730 Hv. The surface hardness of the steel plasma-sulfnitrided with $MoS_2$ was lower than that of ion-nitrided without $MoS_2$. This may be due to the soft FeS layer formed on the surface of the plasma-sulfnitrided steel.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.03a
• /
• pp.47-47
• /
• 2011

최근 m-Aramid 섬유의 염색에 대한 연구가 진행되면서 기존의 원착법 및 초고온고압법 등 상업성이 낮거나 제약이 많았던 염색법에서 차츰 cationic dye를 이용한 염색법이 상용화되고 있다. m-Aramid 섬유는 amide기의 분자 간 수소결합으로 인하여 결정화도를 증가시킴으로서 고강도, 고탄성의 특성을 가질 수 있지만, 강력한 분자구조와 고결정성의 치밀구조로 인하여 염료가 섬유의 분자구조 내부로 확산, 염착되기 어려운 단점을 가지기도 한다. 따라서 m-Aramid 섬유를 침염법으로 염색 시, 섬유의 치밀구조를 이완시켜줄 수 있는 swelling agent가 중요하게 작용한다. 본 연구에서는 cationic dye를 이용하여 swelling agent의 영향성을 살펴보았다. 사용된 시료는 100% m-Aramid 섬유이며, C.I. Basic Yellow 28, Red 46, Blue 54를 사용하여, 욕비 1:10, $NaNO_3$ 7g/l의 조건으로 $130^{\circ}C{\times}60$분간 염색하였다. 이때 사용된 Swelling agent는 두 가지로 각각 1-phenoxypropan-2-ol(S1)과 N-methyl formanilide(S2)를 주성분으로 한다. 염색 시 염료의 농도는 0.5~7% o.w.f.이며, 염색 전 후 염욕을 UV-VIS을 통해 absorbance값을 측정하여 산출한 염착율과, CCM을 사용하여 최대흡수 파장에서 산출 된 K/S값을 비교 고찰 하였다. 각각의 염색물을 비교한 결과 Red 염료를 제외한 yellow 및 blue 모두 3% o.w.f. 염료농도까지 90% 이상의 흡착율을 보였으며, S1에 비해 S2의 경우 염착율이 근소하게 높은 결과를 보였다. 반면 K/S 값을 비교해보면, S2를 사용하였을 때 10%~60% 높은 K/S값을 보였다. 염착율은 비슷하지만 K/S값의 차이를 보이는 이유는 염색이 끝난 후 수세과정에서 섬유표면에 미고착된 염료들이 빠져나가는 것으로, 이를 통해 S2의 경우 섬유의 내부로 염료를 잘 고착시켜 줌으로서 수세안정성이 S1에 비에 우수한 결과를 보인 것으로 고찰된다.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.562-571
• /
• 2006

Mean shear wave velocity of the upper 30m $(V_s30)$ used as the current site classification criterion for determining seismic design ground motions in Korea was established based on the typical depth of site investigations in western US, in which the depth to bedrock is much deeper than that in Korea. In this study, to establish appropriate site classification system for site conditions of Korea, site investigations including in-situ seismic tests to determine shear wave velocity $(V_s)$ were carried out at total 72 sites in Korean peninsula. The mean $V_s's$ to the depths of 5m, 10m, 15m, 20m and 25m together with the $V_s30$ at the testing sites were determined, and the correlation between the mean $V_s$ to a depth shallower than 30m and the $V_s30$ was drawn and suggested for the efficient seismic site classification in Korea. The proposed correlation could be utilized for the seismic design in case of the $V_s$ profiles shallower than 30 m in depth. The correlation in this study, nevertheless, requires further modification by means of the accumulation of various site data in Korea.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.563-564
• /
• 2012

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.189-190
• /
• 2012