• 한국자동차공학회논문집
• /
• 제22권5호
• /
• pp.35-43
• /
• 2014

The automobile industry requires technological innovations to reduce fuel consumption with the public interest in environmental conservation in recent years. Thus, the hybrid system is applied not only to passenger cars but also commercial vehicles. The purpose of this paper is to develop engine ECU_ILS to develop commercial hybrid vehicles. In order to develop the engine and vehicle, the dynamometer and exhaust gas analyzer is needed. However, a lot of time and cost are required. In contrast, the model-based development environment that can be applied to a variety of test conditions can reduce development time. Therefore, a HILS system environment that can consider the behavior of actual vehicles for evaluation of the control logic, fuel consumption and exhaust gas is required. This engine ECU_ILS system was developed in this study, can analyze parameter such as the fuel injection rate, fuel injection time, fuel consumption and exhaust gas like the actual vehicle test using map data. Also, this system is expected to be able to analyze the characteristic of vehicle behavior and the development of peripheral device in relation to engine and vehicles. This HILS system can be used to develop control strategies of commercial hybrid vehicle systems in the future.

• 한국산학기술학회논문지
• /
• 제14권10호
• /
• pp.4665-4671
• /
• 2013

엔진 설치 시스템은 차량의 NVH 성능에 매우 중요한 시스템 이다. 차량의 NVH 성능은 공회전 진동(Idle Vibration), 엔진 쉐이크(Engine Shake) 시동 진동(Key ON/OFF Vibration), 변속 진동(Gear Shift Vibration) 등 다양한 이론이 존재한다. NVH 성능 개선을 위해 이러한 이론들에 대한 실제적 최적화가 필요하며, 특히 최적의 엔진 설치 위치와 강성을 찾아내는 것이 매우 중요하다. 또한 효과적인 NVH 성능 개선을 위하여 차량개발 프로세스 측면에서 제약조건과 한계가 있는 사후 조정보다는 개발 초기에 최적화가 필요하다. 본 논문에서는 엔진 설치 시스템 관련 여러 이론에 대한 최적화 해석과 파워 트레인의 엄격한 모드 분리와 토크롤축(Torque Roll Axis), 탄성롤축(Elastic Roll Axis) 사이의 각도를 최소화 하는 다양한 시뮬레이션 케이스(Simulation Case)와 FE-모드를 개발초기에 수행하여 다중 최적화 분석을 함으로서 최적의 엔진 설치 위치와 강성을 찾아내어 NVH 성능을 개선하였다.

• Journal of Biosystems Engineering
• /
• 제12권1호
• /
• pp.6-13
• /
• 1987

A mathematical model for the waste heat recovery system for an engine was developed. The model based on the experimental data reported before was validated and was used to predict the waste heat recovery and recoverable heat of the engine at various operating conditions of the engine and the system. The model was also used to determine flow rates of the circulating water in the system for a certain temperature increment of the water at various operating conditions of the engine to give basic data to design the system. Stability of the system performance was tested on subjects of vapor lock problem, thermal characteristics of the thermostatic valve, and temperature variation of the circulating water in the engine and fuel consumption of the engine during each mode of the system operation and its change into the other. The test showed that the system operation was stable enough. Temperature profile in the thermal energy storage (TES) was observed during storing thermal energy, and thermal stratification in the TES was well formed acceptable to be used in the system. Finally a scheme to automatize the system was suggested.

• International Journal of Automotive Technology
• /
• 제6권2호
• /
• pp.107-117
• /
• 2005

A distributed hardware-in-the-loop simulation (HILS) platform is developed for designing an automotive engine control system. The HILS equipment consists of a widely used PC and commercial-off-the-shelf (COTS) I/O boards instead of a powerful computing system and custom-made I/O boards. The distributed structure of the HILS system supplements the lack of computing power. These features make the HILS equipment more cost-effective and flexible. The HILS uses an automatic code generation extension, REAL-TIME WORKSHOP$^{ (RTW$^{) of MATLAB$^{ tool-chain and RT-LAB$^{, which enables distributed simulation as well as the detection and generation of digital event between simulation time steps. The mean value engine model, which is used in control design phase, is imported into this HILS. The engine model is supplemented with some I/O subsystems and I/O boards to interface actual input and output signals in real-time. The I/O subsystems are designed to imitate real sensor signals with high fidelity as well as to convert the raw data of the I/O boards to the appropriate forms for proper interfaces. A lot of attention is paid to the generation of a precise crank/ earn signal which has the problem of quantization in a conventional fixed time step simulation. The detection of injection! command signal which occurs between simulation time steps are also successfully compensated. In order to prove the feasibility of the proposed environment, a simple PI controller for an air-to-fuel ratio (AFR) control is used. The proposed HILS environment and I/O systems are shown to be an efficient tool to develop various control functions and to validate the software and hardware of the engine control system.

• 한국추진공학회지
• /
• 제23권1호
• /
• pp.124-131
• /
• 2019

가스터빈엔진 고도시험설비 운용특성탐색 및 설비튜닝 연구와 유량/추력 측정방안 검증을 위한 엔진 시뮬레이션덕트 설계 연구를 수행하였다. 설비 운용특성 검증은 배압/추력 제어가 필요하므로 Spikecone type의 가변노즐을 적용하였으며, 유량검증용 ISO 쵸킹노즐의 추가장착이 가능토록 설계하였다. 시뮬레이션덕트 주유로 면적은 1D Sizing으로 결정하고, 노즐면적변화에 따른 시뮬레이션덕트 내부 유동특성은 1D/CFD 해석으로 조사하였으며, 해석결과로부터 설비운용특성 탐색 및 유량/추력 검증시험을 위한 공기공급부 시험조건을 도출하였다. Spike 노즐 구동부는 시험 전운용 구간에서 공력하중조건을 견디도록 모터, 리니어 볼스크류 등의 부품모델을 선정하였으며, 시험 시 10 mm/s의 이송속도가 가능하도록 설계하였다.

• 한국산업경영시스템학회:학술대회논문집
• /
• 한국산업경영시스템학회 2002년도 춘계학술대회
• /
• pp.445-454
• /
• 2002

This article explains the theory of multiple mode/physical coordinate synthesis method in order to analyze the dynamic characteristics for an huge marine engine. The theory leads to make a simulation code. The natural frequencies obtained from the simulation code is compared to those from a commercial analysis software, ANSYS. The simulation code is well reviewed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.208.1-212
• /
• 1997

In this paper, a computer simulation tool for evaluting integrated engine/transmission control system using MATLAB/SIMULINK is investigated. Since a modular programming technique based upon the object-oriented programming is used in the paper, the simulation tool developed reduces the burden of model complexity by dividing engine/transmission systems into hierarchical subsystem. Furthermore, it also provides user -friendly, reusable, and upgradable characteristics of the system. The simulation tool could be useful to the automotive engineers who frequently change models and develop new systems in the automotive powertrain and control area.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2009년도 추계학술대회
• /
• pp.38-39
• /
• 2009

시뮬레이션 가시화 기술은 사용자가 직접 접하게 되는 기술이며, 시뮬레이터 사용자들은 보다 빠르고, 보다 현실적이며 보다 직관적인 영상을 요구하고 있다. 컴퓨팅 기술 및 영상장비 기술 등의 하드웨어는 우수한 성능으로 발전된 반면, 현재 일반적으로 선박 운항 시뮬레이터에 사용되고 있는 그래픽 렌더링 엔진은 그 한계를 나타내고 있다. 이러한 배경에서 본 논문에서는 예부선 시뮬레이션 시스템의 가시화툴 위해 필요한 시스템의 요구사항을 도출하고 상용 및 공개용 그래픽 렌더링 엔진에 대한 조사/검토하고, 시스템 요구사항을 만족시키기 위한 그래픽 렌더링 엔진의 장단점을 분석하여, 향후 그래픽 렌더링 엔진의 활용가능성을 평가하였다.

• 한국시뮬레이션학회논문지
• /
• 제17권2호
• /
• pp.1-12
• /
• 2008

자동차 엔진을 구성하는 주요부품은 실린더블록, 실린더헤드, 크랭크샤프트, 커넥팅로드, 캠샤프트 등으로 구성되는데 이들의 영문명을 따서 5C라고 부른다. 따라서 일반적으로 엔진공장은 5C를 생산하는 라인과, 엔진 조립라인을 포함하는 6개의 라인으로 구성이 된다. 엔진공장은 소품종대량생산의 특성을 가지기 때문에 장비의 배치형태는 흐름라인의 형태를 따른다. 본 논문에서는 국내 자동차 회사 엔진공장의 크랭크샤프트라인 설계를 위한 시뮬레이션 사례를 소개한다. 크랭크샤프트 라인은 기계가공을 중심으로 하는 라인이다. 따라서 라인설계에 영향을 미치는 요인들에 대해 소개하고, 라인 효율에 미치는 영향을 $QUEST^{(R)}$라는 3차원 시뮬레이션 도구를 이용하여 분석하였다. 기술팀에서 제시한 초기배치안에 대해 시뮬레이션 모델을 구축한 후 실험을 통하여 시스템 효율을 개선시키기 위한 방법을 제시하였다.

• 한국자동차공학회논문집
• /
• 제7권7호
• /
• pp.86-93
• /
• 1999

Turbocharger has been used to increase the performance of diesel engine, especially ship engine , for years. Recently, the turbocharger is being adopted not only for an agricultural engine but also for an automobile engine. To improve the performance of diesel engine , the problem of the reduction of A/F ratio in high speed should be solved. Turbocharger is well known for its cost effectiveness, reliability and duration . In this study, an experiment was conducted to verify simulation program . The results for natural aspiration engine and turbocharged engine were compared. In order to estimate the characteristics of exhaust gas, D-13 mode was selected. Power, torque and BSFC of turbocharged engine were increased than those of natural aspiration engine by about 48%, 46% and 5%, respectively . The components in exhaust gas except NOx from turbocharger engine were less than the amount set up for 2000-year regulation.