• Journal of Advanced Marine Engineering and Technology
• /
• v.8 no.2
• /
• pp.74-80
• /
• 1984

In the reduction gears for marine propulsion engine such as turbine or high speed diesel engine, the standard involute double helical gears are generally used. However the addendum modification gear can be used in the reduction gear as it has flexibility for gear design on the tooth strength, scoring and operating noise. In this case, the determination of gear shaft bearing load is difficult by the alternation of operating pressure angle. In this paper, the formulas of bearing load according to the arrangements of the reduction gears are derived and the diagrams of operating pressure angle according to the modification coefficient are presented.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.3
• /
• pp.63-70
• /
• 1998

According to the stringent exhaust emission regulation control of air fuel ratio is one of the most important issues on gasoline engine. Although many researches have been carried out to identify the fuel transport phenomena in a port fueled gasoline engine, complexity of fuel film behavior in the intake port makes it difficult. The fuel film behavior was investigated recently by using visualization method and these gave us qualitative understanding. In this paper, the quantitative measurement method for the port fuel film is studied by using Fast Response Flame Ionization Detector(FRFID). The mass of fuel film on the port wall was measured by using the methods of fuel injection off, injection on and regression. The Fuel film mass was increased with incresing load at the same engine speed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.6
• /
• pp.40-50
• /
• 2000

In this study, as a means of increasing engine power, turbocharging was applied to the gasoline engine of a light passenger car which was originally naturally aspirated. Also the catalytic convertor was applied to improve the exhaust emission characteristics. The comparison of the performance characteristics between the burbocharged engine with catalytic convertor and the naturally aspirated engine was made over the wide range of operating conditions. The results showed considerable increase of the output performances at full load condition by trubocharging while slight losses were observed at part load conditions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.1
• /
• pp.41-49
• /
• 1993

Piston slap is one of the major sources of noise in a 4-cycle diesel engine. Piston slap is not only one of major source mounted near the top and bottom of the piston thrust and antithrust skirts. Effects of engine speed, load and coolant temperature on piston motion were investigated. The measured piston motion showed 6 slapes per cycle resulting from the change of side force. Major piston slap timing was retarded as engine speeds became higher. The increase of engine load made large piston transverse movement toward thrust side of cylinder block. Piston transverse movement was due to reduced piston-liner clearance at higher coolant temperature.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.6
• /
• pp.628-636
• /
• 2005

In this paper. the effects of a WI(Water Injection) in the intake pipe for a 4-cylinder Dl(Direct Injection) diesel engine are investigated experimentally, The WI system was controlled by the duty cycle from the intake manifold's temperature and MAF(Manifold Air Flow) First. effect of EGR on NOx reduction was investigated. Then WI system was applied to reduce NOx As the results. we can make the NOx map and visualize the NOx results by variation of engine speed and engine load It was known that effect of WI system on NOx reduction without the EGR was better than the with EGR base engine except of low load and speed condition.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.7
• /
• pp.1082-1091
• /
• 2004

Analyzed Parametrically was an internal combustion engine combined with gas turbine the cycle of which is splitted into compression side cylinder and expansion side one, and heat adding of which is during constant volume pressure, temperature process. The advantages of each measures were analyzed by means of thermal cycle diagram. The thermal efficiency of partial load cutting off firstly isothermal heat adding and secondly isobaric heat adding also was analyzed The authors suggested some potentials about the performance as for thermal efficiency, mean effective pressure and reducing emissions and noise supposed were the operating parameter of the engine set to some values and were some problems solved.

• Journal of Advanced Marine Engineering and Technology
• /
• v.13 no.3
• /
• pp.26-36
• /
• 1989

Recently digital governor system is commonly adapted for the speed control of the marine diesel engine because of too much fluctuation of rpm resulted by the low speed, long stroke, high efficiency and a small number of cylinder of it, and versatile studies on the development of digital governor system are progressed. On this subject the new control method in which the fuel is controlled by feedforwarding the change of load as well as the feedback of angular velocity in case of disregarding the engine dead time and influence of scavenging air was proposed by the authors, and found the method has shown quite a good control performance in comparision to the conventional control method by the simulation using a digital computer for various load change. In this paper the speed control system of a diesel engine is simulated in case of regarding the engine dead time by the proposed method, and also confirm a good control performance of it under even more realistically simulated environment.

• Journal of Energy Engineering
• /
• v.19 no.1
• /
• pp.32-38
• /
• 2010

The objective of the research was to study the effects a Miller cycle. The engine was dedicated to natural gas usage by modifying pistons, fuel system and ignition systems. The engine was installed on a dynamometer and attached with various sensors and controllers. Intake valve timing, engine speed, load, injection timing and ignition timing are main parameters. Miller Cycle without supercharging can increase brake thermal efficiency 1.08% and reduce brake specific fuel consumption 4.58%. The injection timing must be synchronous with valve timing, speed and load to control the performances, emissions and knock margin. Throughout these tested speeds, original camshaft is recommended to obtain high volumetric efficiency.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.47-56
• /
• 2001

Nitrogen oxides(NOx) and smoke emissions of diesel engine are regarded as a source of air pollution, and there is a global trend to enforce more stringent regulations on these exhaust gas emissions. However, the trade-off relation of NOx and smoke is a main obstacle to reduce both of them simultaneously. In this paper, experiments were conducted with an oxygenated fuel(diethyl ether) as an effective way to improve the trade-off relation of NOx and smoke. Exhaust emissions of diesel fuels with DEE were influenced by the additive content of DEE and the injection timing. Especially, DEE effected more at the high engine speed and load than at the low engine speed and load. Diesel fuel blended with DEE 10% was a desirable blend for the simultaneous reduction of NOx and smoke.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.18 no.5
• /
• pp.492-497
• /
• 2015

Currently, there are many kinds of tracked armored vehicles in service and they have encountered various environment and situations. So there are many obstacles to operate them improperly such as an engine stall. The causes of engine stall are an insufficient fueling, a mixture of air-fuel or vapor lock, and load increment which results from a rapid steering or increasing a viscosity of lubricant by low temperature. In this paper, engine stall by load increment due to a rapid steering or increasing of lubricant viscosity on tracked armored vehicles is analyzed, the ways to prevent it are applied, and their degrees of improvement are evaluated.