• Journal of Welding and Joining
• /
• 제31권3호
• /
• pp.22-30
• /
• 2013

Due to ELV banning, automotive electronics cannot use four kinds of heavy metal element (Pb, Hg, Cd, $Cr^{6+}$) from 2016. Therefore, this study was focused on degradation characteristics of Sn-3.0Ag-0.5Cu Lead-free solder joint with OSP and ENIG finsh under various reliability assessment method, as like to thermal shock test and high temeprature/high humidity test with test duration for cabin electronics. Also, we compared bonding strength degradation to other advanced research results of electronic control unit for engine room because of difference service temperature with mount location in automotive. Whisker growth phenomenon and mitigation method which were essentially consideration items for Pb-free car electronics were examined. Conformal coating is a strong candidate for mitigating whisker growth in automotive electronics. Necessary condition to adapt Pb-free in car electronics was shown.

• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.156-165
• /
• 2014

This paper is the first investigation on the effect of flow control methods on the part load performance in a spark ignition engine. For comparison of the methods, two control devices, port throttling and masking, were applied to a conventional engine without any design change of the intake port. Steady flow evaluation shows that steady flow rates per unit opening area and swirl ratio are very low compared with the port throttling and saturated from mid-stage valve lift, however, swirl increases slightly as the lift is higher in case of 1/4 masking control. In the part load performance, the effect of simple port throttling on lean misfire limit expansion is limited and insufficient; on the other hand a masking improves the limit considerably without any port modification for increasing swirl. Also the results show that the intake flow control improves the combustion with following two mechanisms: stratification induced by the combination of the flow pattern and the fuel injection timing attribute to ignition ability and the intensified flow ensure fast burn. In addition fuel consumption reduces under the flow controls and the reduction rate is different according to the operation conditions and control methods. At the Stoichiometric and/or low speed and low load the throttling method is more advantageous; however vice versa at lean and high load condition. Finally, the throttling is more efficient for HC reduction than masking, on the other side the NOx emissions increase under the masking and decrease under the port throttling compared with conventional port scheme.

• International Journal of Automotive Technology
• /
• 제4권1호
• /
• pp.41-45
• /
• 2003

The 42V Mild Hybrid System has been released into market by Toyota for the first time in the world in 2001. The set-up employs an inverter unit to control the motor/generator (MG) electronically. The driving system called such as Toyota Mild Hybrid System (TMHS) has additional new functions to conventional internal combustion engines. When stopping vehicle, the engine stops promptly. When starting vehicle, by releasing the brake pedal MG starts the vehicle at the same time (EV-driving mode). When stepping on the accelerator pedal, or after a given period of time the engine firing occurs and the engine-driving mode starts. When running by motor, the power is supplied to the motor from 36V battery through the inverter. High outputs and instant responses are required for Inverter. At the same time, the compact volume is required to fit into the limited space of the engine room. The compact size and high output are also required to Power Capacitor used for this inverter. The power capacitors has been newly developed, shaped in "flat" type, suitably for the inverter. The points of developments on inverter and power capacitor are described in this paper.his paper.

• 한국통신학회논문지
• /
• 제40권12호
• /
• pp.2503-2510
• /
• 2015

본 논문에서는 전력 정보를 측정하기 위한 단상 에너지 측정용 IC의 구현 방법을 제안한다. 제안된 전력 측정용 IC는 2개의 PGA(Programmable Gain Amplifier), 2개의 ${\sum}{\Delta}$ modulator, reference 회로, LDO(Low-dropout) regulator, 온도 센서, 필터부, 계산 엔진, 보정 제어부, 레지스터, 외부 인터페이스로 구성된다. $0.18-{\mu}m$ CMOS 공정으로 제작되었고, 32-pin QFN package로 제작되었다. 구현된 IC는 3.3V 전원을 공급받아 동작하며, 동작 클럭 주파수는 4,096 kHz이고, IC 동작시 소비 전력은 10 mW이다.

• 한국가스학회지
• /
• 제11권4호
• /
• pp.54-58
• /
• 2007

본 연구에서는 13L급 전자제어식 디젤 엔진을 혼소 엔진으로 개조하여 얻은 결과를 다루고 있다. 혼소 엔진 개조 후 차량의 출력, 연료경제성, 운전성 등을 파악하기 위하여 일정한 경로의 고속도로를 주행하였다. 개조된 차량은 최대 85%의 대체율을 가지며 500 km의 거리를 혼소 모드로 주행하였다. 차량의 주행성능은 디젤 모드의 경우와 거의 동일하였으나, 추월 가속성능이 약간 떨어지는 경향이 있었다. 엔진의 최대출력, 열효율, 배기가스 측정을 위하여 차량 시험과는 별도로 엔진 시험도 동시에 수행하였다. ND-13모드에서 배출가스 배출량 측정 실험을 수행한 결과, 산화촉매를 장착한 혼소모드에서의 배출가스 배출량은 디젤모드에서와 출력은 동일하게 유지하면서 K2006 규제를 만족함을 알 수 있었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 D
• /
• pp.2380-2382
• /
• 2004

In this paper, Web server is built up using PXA255, 32bit RISC processor with porting Embedded Linux and GoAhead, HTTP(Hyper Text Transfer Protocol) web server, and the system with can monitor and control the environment and condition for AICC(Automatic Intelligent Cruise Control) is realized. For sending the operation condition and change of vehicle the desired data is derived by interacting ECU(Electric Control Unit) and Embedded system and the rpm of engine is controlled by step motor connected to throttle value.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.211-217
• /
• 2007

The Diesel Multiple Units (DMU) is a successful mass transportation system, that is being, continuously, on demand by train operators and railway authorities around the globe. One of its advantages is the fact that a diesel engine, along with the correct propulsion and control equipment. This paper describes a study on the Power Pack developed for Ireland DMU to help comprehensive concept of Diesel Propulsion System.

• International Journal of Reliability and Applications
• /
• 제12권2호
• /
• pp.79-94
• /
• 2011

Redundancy-reliability allocation problems in multi-stage series-parallel systems are addressed in this study. Fuzzy programming techniques are proposed for finding satisfactory solutions. First, a multi-objective programming model is formulated for simultaneously maximizing system reliability and minimizing system total cost. Due to the nature of uncertainty in the problem, the fuzzy set theory and technique are used to convert the deterministic multi-objective programming model into a fuzzy nonlinear programming problem. A heuristic method is developed to get satisfactory solutions for the fuzzy nonlinear programming problem. A Pareto optimal solution is found with maximal degree of satisfaction from the interception area of fuzzy sets. A case study that is related to the electronic control unit installed on aircraft engine over-speed protection system is used to implement the developed approach. Results suggest that the developed fuzzy multi-objective programming model can effectively resolve the fuzzy and uncertain problem when design goals and constraints are not clearly confirmed at the initial conceptual design phase.

• 한국자동차공학회논문집
• /
• 제23권2호
• /
• pp.153-160
• /
• 2015

Hybrid Electric Vehicles(HEVs) have seriously come into prevalence recently as car manufacturers and consumers have become more aware of the environmental and economic problems of conventional vehicles. For the alternative power-train and battery cooling systems in HEVs, an effective thermal management system is required, and many automakers are interested in using Brushless DC(BLDC) motors for cooling fans for the overall traction unit's performance and energy saving capability. This paper presents the development status of BLDC motors as major parts of the power-train, i.e. the engine cooling and battery cooling fans of HEVs. A design that uses BLDC motors for the power-train and each battery cooling fan, is successfully implemented through using electro-magnetic analysis, and prototype BLDC motors are examined. As experimental results, the BLDC motors achieved an efficiency of 85% as engine cooling fans and 72% as a battery thermal management fan motor. The electric cogging noise is significantly reduced by changing the skew of the slot pitch angle and optimizing the magnetic shape.

• 대한기계학회논문집A
• /
• 제27권4호
• /
• pp.531-536
• /
• 2003

In order to control the railway noise. we should know the radiation characteristic of the noise during the train passage Generally, the railway noise sources for conventional trains are classified by the rolling noise and power unit noise in tangent track. In this Paper. we describe on a train model that is considered to be a row of point sources to calculate the radiation characteristic The calculation results are compared with short distance measurement of three kinds of trains (EMU, Mookungwha, Saemaul). It is shown that the radiation characteristic of the rolling noise that is major noise source of electric multiple unit is dipole type. We know that characteristic of the engine noise is radiated as the cosine type.