• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.5
• /
• pp.90-99
• /
• 1996

To keep up with the regulation of OBD II(on board diagnostics II), many detection methods for engine misfire have been developed. Among them, the method of using the crankshaft speed fluctuation is the most noticeable in the point of view of lower cost and easier installation than any others. On the basis of the results obtained from the previous engine-dynamometer test, the integrating torque index (ITI) has been introduced. In this research, the instrumental and the interfacing systems to engine control unit(ECU) are developed for the vehicle test. Therefore, the vehicle and chassis-dynamometer test can be carried out in addition to the rough road test. From this test, the previousproposed method proved that it can be applied to the real vehicle.

• International Journal of Precision Engineering and Manufacturing
• /
• v.5 no.2
• /
• pp.46-52
• /
• 2004

Numerous connectors are used in automobiles for transmission of electrical signals across various electro-mechanical components. The connectors must operate with high reliability in order to minimize failures due to signal degradation. In this work, the effects of contamination at the contact interface of connectors used fur automobile crankshaft position sensor on the impedance change were investigated. An experimental set-up was built to simulate the electrical signal transmitted from the sensor to the engine control unit through a connector. Output from the connector was investigated using connectors contaminated with engine block residues and water droplets. It was found that slight contamination of the connectors could lead to significant signal degradation which can lead to engine failure. Also, the effect of water in the connector altered the signal severely. However, the signal gradually regained the original state as the water evaporated from the interface.

• Journal of the Korean Institute of Gas
• /
• v.19 no.6
• /
• pp.22-27
• /
• 2015

Hydrogen features highest energy density per mass and is expected to be desirable as a fuel of HALE(High altitude long endurance) UAV(Unmanned aerial vehicle). A reciprocating internal combustion engine is known to be a reliable and economic power source for this kind of UAV. Therefore, the combination of hydrogen and engine is worth of doing research. Test bench with 2.4L Spark-Ignited engine was prepared for the experiment in which start and combustion characteristics at idle condition were examined in this study. Stable hydrogen supply system and a universal ECU(Engine control unit) were also utilized for the test engine. Equivalence ratio and spark timings at idle operation were investigated and compared to the data of gasoline engine. The results will be a starting point for full-scale research of hydrogen engine for HALE UAV.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.31-35
• /
• 2008

This test cell is developed to provide the fundamentals of operational mechanism and structural configuration, and further to verify thermodynamic calculation with this test data to the institutes or laboratories research and study gas turbine engine for academic purpose. The test cell is installed to monitor and collect real-time data as to temperature, pressure, thrust, fuel flow, and air flow etc. using by NI DAQ(Data acquisition)device and LabVIEW program based on 30lbf-micro turbojet engine.

• Journal of Korea Multimedia Society
• /
• v.11 no.10
• /
• pp.1436-1445
• /
• 2008

Currently, mobile handset embeds many communication modules including CDMA and Bluetooth, and many applications are developed based on these modules. In this paper, we study about wireless vehicle diagnosis software and user interface based on bluetooth system on mobile handset. We developed Bluetooth communication system on protocol converter between OBD(On Board Diagnostics)-II system. Based on this system, we can communicate ECU(Engine Control Unit) and mobile device based on windows .NET compact framework platform. Therefore we can easily diagnose vehicle state and obtain engine data. All user interface and vehicle diagnosis systems on mobile handset are developed under windows .NET compact framework platform. Using this system we achieved several improvements over existing vehicle diagnostic system; 1) the software download and upgrade can be achieve on wireless environment, 2) no additional diagnostic devices are requires, which saves additional cost and we can diagnose the vehicle easily, 3) we can easily port our system on many embedded systems including PDA and navigator, etc.

• Journal of Aerospace System Engineering
• /
• v.17 no.6
• /
• pp.144-148
• /
• 2023

Aircraft battery is the core equipment of an aircraft that supplies engine starting power and emergency power, and it must be charged to ensure sufficient capacity at all times and maintain high reliability to ensure stable power supply. The battery of the T-50 series aircraft is designed to enable the engine to start up to two times in temperatures as low as -18℃ and above. However, intermittent failures in engine starting have been observed during winter. In this paper, we analyze the failure phenomena occurring during low-temperature charging of the battery and improve the charging algorithm based on the analysis and test. Additionally, the results of start simulation tests show that the battery charging defects at low temperatures are resolved, and an improvement in the charging performance is confirmed; thus, validating the effectiveness of the new algorithm.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.3
• /
• pp.20-28
• /
• 2007

The easiest way to see the phenomena of compressor surge is to show the static and dynamic operation characteristic on the map. Its operation zone will be restricted by the surge limit and, static and transient process must have some margin for it. Effect of rotor moment of inertia, air/gas volumes and heat transfer are factors to cause the transition from the static line. In case a large volume such as heat exchanger exists in the system it will exert a substantial influence to dynamic characteristics. In the present paper, influence of air volume bled from the compressor exit on transient process is investigated with an example of an auxiliary power unit micro-turbine engine. Turbine mass, pressure ratio, rotation speed, power and moment are calculated based on mass and work conservation. Result from the present study can give guidance to design the control system. A computer program is developed to calculate the dynamic process using the MathCAD commercial software.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.2
• /
• pp.118-125
• /
• 2009

Calculation of indicated mean effective pressure(IMEP) requires high cylinder pressure sampling rate and heavy computational load. Because of that, it is difficult to implement in a conventional electronic control unit. In this paper, a cylinder pressure based real-time IMEP estimation method is proposed for controller implementation. Crank angle at 10-bar difference pressure($CA_{DP10}$) and cylinder pressure difference between $60^{\circ}$ ATDC and $60^{\circ}$ BTDC($DP_{deg}$) are used for IMEP estimation. These pressure variables can represent effectively start of combustion(SOC) and fuel injection quantity respectively. The proposed IMEP estimation method is validated by transient engine operation using a common-rail direct injection diesel engine.

• Journal of ILASS-Korea
• /
• v.28 no.4
• /
• pp.191-197
• /
• 2023

LPG direct injection (LPDi) technology is a method of improving the weaknesses of existing LPG vehicles by directly injection into the combustion chamber. This study was conducted on the comparison of emissions and fuel efficiency performance of the engine and vehicle by applying LPDi technology. The LPDi hybrid engine's maximum output and maximum torque were measured at an equivalent level of less than 1% compared to conventional gasoline fuel. The fuel amount was corrected using the LCU controller, and the THC, CO, and NOx emissions were reduced to 90% in the operating range of the three-way catalyst through air-fuel ratio control. The analysis of THC+NOx and CO emissions in FTP-75 (CVS-75) driving mode satisfied the US LEV III SULEV30 regulation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.9
• /
• pp.1965-1971
• /
• 2010

A ship propulsion thruster platform which is used by safety sailing takes charge of remote control of a main engine in ship. This system not only guarantees safety and reliable flight sailing but also require remote control technology of a ship. Accordingly, in this paper it deals with a telegraph lever control unit system which is a part of propulsion thruster system as localization technology. Also it makes sure of knowledge and core technology through analysis and designing and developing a telegraph lever control unit system. Moreover, it is sure of acquisition of base technology for integration of a ship propulsion thruster platform.